Home > Netgear > Router > Netgear Wndr3400v3 N600 Wireless Dual Band Router User Manual

Netgear Wndr3400v3 N600 Wireless Dual Band Router User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Netgear Wndr3400v3 N600 Wireless Dual Band Router User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 137 Netgear manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Hardware Setup 11
     N600 Wireless Dual Band Router WNDR3400v3
    Hardware Features
    Before you cable your router, take a moment to become familiar with the \
    label and the front 
    and back panels. Pay particular attention to the LEDs on the front panel\
    .
    Front Panel
    The router front panel has the status LEDs and icons shown in the follow\
    ing figure.
    WPS button
    Wireless On/Off button
    WPS LED
    USB LED
     
    LAN Ports 1
    –4 LEDs
     
    Internet LED
    5 GHz Wireless LED 
    2.4 GHz Wireless LED 
    Power/Test LED 
    						
    							Table 1.  Front panel LED descriptions  
    LEDDescription
    WPS
    •  Solid green . Wireless security is enabled.
    •  Blinking green . 
     The router is using WPS to add a wireless device to the network.
    •  Off. No WPS connection exists.
    USB
    •  Solid green . USB drive is properly mounted.
    •  Off. No USB drive is detected. USB drive is missing or not mounted correctl\
    y
     .
    LAN ports 
    1–4
    •  Solid green . The LAN port has detected a 100 Mbps link with an attached device.
    •  Solid amber . 
     The LAN port has detected a 10 Mbps link with an attached device.
    •  Off. No link is detected on this port.
    Internet
    •  Solid amber . The IP address was not acquired.
    •  Solid green . 
     An IP address was received; ready to transmit data.
    •  Off. No Ethernet cable is connected between the router and the modem.
    5 GHz
    •  Solid blue . The wireless radio is operating.
    •  Off. The 
     wireless radio is off.
    2.4 GHz
    •  Solid green . The wireless radio is operating.
    •  Off. The 
     wireless radio is off.
    Power/Test
    •  Solid amber . The unit is starting up after being powered on.
    •  Solid green . 
     The power is on and the router is ready.
    •  Blinking amber . A 
     firmware  update  is  in  progress.
    •  Blinking green . The 
     firmware is corrupt.
    •  Off. Power is not supplied to the router.
    Hardware Setup 
    12
    N600 Wireless Dual Band Router WNDR3400v3  
    						
    							Hardware Setup 13
     N600 Wireless Dual Band Router WNDR3400v3
    Back Panel
    The back panel has the connections shown in the following figure.
    USB 2.0 port 
    .Restore Factory Settings button. Press and hold this 
    button for about 5 seconds to reset the router to its factory 
    default settings.
     
    Four local area networks (LAN) 10/100 Mbps Ethernet 
    ports for connecting the router to your local computers. 
    Internet/Wide Area Network (WAN) Ethernet port for 
    connecting the router to a cable or DSL modem. 
    AC power adapter outlet for connecting the power adapter.  Power On/Off button 
    See Factory Settings on page  106 for information about restoring factory settings.  
    						
    							Hardware Setup 14
    N600 Wireless Dual Band Router WNDR3400v3 
    Label
    The label on the bottom of the router shows the WPS PIN, login informati\
    on, MAC address, 
    and serial number. 
    Cable Your Router
    Refer to the installation guide that came in the WNDR3400v3 router box f\
    or cabling 
    information. 
    Verify the Cabling
    Verify that your router is cabled correctly by checking the router LEDs. \
    Turn on the router by 
    pressing the On/Off.
    Table 2.  
    LEDDescription
     
    The Power/Test LED is green when the router is turned on.
    The LAN ports are green for each computer cabled to the router by an Eth\
    ernet cable.
    Verify that the LAN LEDs (1 through 4) are lit for any computers cabled\
     to the router by an Ethernet 
    cable. 
    						
    							Hardware Setup 15
     N600 Wireless Dual Band Router WNDR3400v3
     
     
    The Wireless LEDs are lit.
    The Internet LED is lit. If it is not, make sure that the Ethernet cable\
     is securely attached to the  router Internet port and the modem, and that the modem is powered on.
    Table 2.  
    LEDDescription 
    						
    							16
    2
    2.   Getting Started with NETGEAR 
    genie
    Connecting to the router
    This chapter explains how to use NETGEAR genie to set up your router after you complete 
    cabling as described in the installation guide and in the previous chapter in this book.
    This chapter contains the following sections:
    •Router Setup Preparation 
    •Types of Logins and Access 
    •NETGEAR genie Setup 
    •Use NETGEAR genie after Installation 
    •Upgrade Router Firmware 
    •Router Dashboard (Basic Home Screen) 
    •Add Wireless Devices or Computers to Your Network  
    						
    							Getting Started with NETGEAR genie 
    17  N600 Wireless Dual Band Router WNDR3400v3
    Router Setup Preparation
    You can set up your router with the NETGEAR genie automatically, or you can use the Genie 
    menus and screens to set up your router manually. However, before you start the setup 
    process, you need to have your ISP information on hand and make sure the laptops, PCs, 
    and other devices in the network have the settings described here.
    Use Standard TCP/IP Properties for DHCP
    If you set up your computer to use a static IP address, you need to change the settings so 
    that it uses Dynamic Host Configuration Protocol (DHCP). 
    Gather ISP Information
    If you have DSL broadband service, you might need the following information to set up your 
    router and to check that your Internet configuration is correct. Your Internet service provider 
    (ISP) should have provided you with all of the information needed to connect to the Internet. 
    If you cannot locate this information, ask your ISP to provide it. When your Internet 
    connection is working, you no longer need to launch the ISP login program on your computer 
    to access the Internet. When you start an Internet application, your router automatically logs 
    you in.
    •The ISP configuration information for your DSL account
    •ISP login name and password
    •Fixed or static IP address settings (special deployment by ISP)
    Wireless Devices and Security Settings
    Make sure that the wireless device or computer that you are using supports WPA or WPA2 
    wireless security, which is the wireless security supported by the router. See 
    Basic Wireless 
    Settings on page 29 for information about the router’s preconfigured security settings.
    Types of Logins and Access
    There are two separate types of logins that have different purposes. It is important that you 
    understand the difference so that you know which login to use when.
    •Router login logs you in to the router interface from NETGEAR genie. See Use 
    NETGEAR genie after Installation on page 18 for details about this login.
    •ISP login logs you in to your Internet service. Your service provider provided you with 
    this login information in a letter or some other way. If you cannot find this login 
    information, contact your service provider.
    •Wireless network key or password. Your router is preset with a unique wireless 
    network name (SSID) and password for wireless access. This information is on the label 
    at the bottom of your router. 
    						
    							Getting Started with NETGEAR genie 
    18 N600 Wireless Dual Band Router WNDR3400v3 
    NETGEAR genie Setup
    NETGEAR genie runs on any device with a web browser. It is the easiest way to set up the 
    router because it automates many of the steps and verifies that those steps have been 
    successfully completed. It takes about 15
     minutes to complete. 
    Using NETGEAR genie to set up your router:
    1. Turn on the router by pressing the On/Off button. 
    2. Make sure that your device is connected with an Ethernet cable to your router.
    3. Launch your Internet browser.
    •The first time you set up the Internet connection for your router, the browser 
    automatically goes to http://www.routerlogin.net, and the NETGEAR genie screen 
    displays.
    •If you already used the NETGEAR genie, type http://www.routerlogin.net in the 
    address field for your browser to display the NETGEAR genie screen. See 
    Use 
    NETGEAR genie after Installation on page 18.
    4. Follow the instructions on the screen to complete the NETGEAR genie setup. NETGEAR 
    genie guides you through connecting the router to the Internet. 
    If the browser cannot display the web page: 
    •Make sure that the computer is connected to one of the four LAN Ethernet ports, or 
    wirelessly to the router.
    •Make sure that the router is up and running. Its Wireless LEDs should turn on.
    •Close and reopen the browser to make sure that the browser does not cache the previous 
    page.
    •Browse to http://www.routerlogin.net.
    •If the computer is set to a static or fixed IP address (this is uncommon), change it to 
    obtain an IP address automatically from the router.
    If the router does not connect to the Internet :
    1. Review your settings to be sure that you have selected the correct options and typed 
    everything correctly. 
    2. Contact your ISP to verify that you have the correct configuration information.
    3. Read Chapter 9, Troubleshooting. If problems persist, register your NETGEAR product and 
    contact NETGEAR technical support.
    Use NETGEAR genie after Installation
    When you first set up your router, NETGEAR genie automatically starts when you launch an 
    Internet browser on a computer that is connected to the router. You can use NETGEAR 
    Genie again to view or change settings for the router. 
    						
    							Getting Started with NETGEAR genie 19
     N600 Wireless Dual Band Router WNDR3400v3
    1. 
    Launch your browser from a computer or wireless device that is connected\
     to the router.
    2.  T
    ype  http://www.routerlogin.net  or http://www.routerlogin.com .
    The login window displays:
    admin
    ********
    3.  Enter  admin  for the router  user name and password for the  router password, both in 
    lowercase letters. 
    Note: The router user name and password are different from the user name 
    and password for logging in to your Internet connection. See  Types of 
    Logins and Access  on page
      17 for more information.
    Upgrade Router Firmware
    When you set up your router and are connected to the Internet, the route\
    r automatically 
    checks for you to see if newer firmware is available. If it is, a messag\
    e is displayed on the top 
    of the screen. See  Upgrade the Router Firmware on page  66 for more information about 
    upgrading firmware.
    Click the message when it shows up, and click  Y
     es to upgrade the router with the latest 
    firmware. After the upgrade, the router restarts.
    CAUTION:
    Do not try to go online, turn off the router, shut down the computer, or do 
    anything else to the router until the router finishes restarting and the\
     
    Power LED has stopped blinking for several seconds.
    Router Dashboard (Basic Home Screen)
    The router Basic Home screen has a dashboard that lets you see the statu\
    s of your Internet  connection and network at a glance. You can click any of the six sections of the dashboard to  
    						
    							Getting Started with NETGEAR genie 20
    N600 Wireless Dual Band Router WNDR3400v3 
    view more detailed information. The left column has the menus. At the top is an Advanced 
    tab that is used to access more menus and screens.
    Language
    Dashboard 
    (Click to 
    view 
    details)
    Menus 
    (Click the 
    Advanced  tab to 
    view 
    more)
    Figure 1. Router Basic Home screen with dashboard, language, and online \
    help
    • Home. This dashboard screen displays when you log in to the router. 
    • Internet. Set, update, and check the ISP settings of your router.
    • W
    ireless . View or change the wireless settings for your router.
    • Attached Devices. V
     iew the devices connected to your network.
    • Parental Controls. Download and set up parental controls to prevent objectionable 
    content from reaching your computers. 
    • ReadySHARE. If you connected a USB storage device to the router it is displayed he\
    re.
    • Guest Network. Set up a guest network to allow visitors to use your router’
     s Internet 
    connection.
    • Advanced tab. Set the router up for unique situations such as when remote access by \
    IP 
    or by domain name from the Internet is needed. See Chapter 8, Advanced Settings. 
    Using this tab requires a solid understanding of networking concepts.
    • Help & Support. Go to the NETGEAR support site for information, help, and product 
    documentation. 
    
    These links work once you have an Internet connection.
    Add Wireless Devices or Computers to Your Network
    Choose either the manual or the WPS method to add wireless devices and o\
    ther equipment 
    to your wireless network. For instructions on setting up a guest network\
    , See  Guest Networks 
    on page   32. 
    						
    All Netgear manuals Comments (0)

    Related Manuals for Netgear Wndr3400v3 N600 Wireless Dual Band Router User Manual