Netgear Netgar VPN FIrewall FVS336Gv2 Reference Manual

Set Up Virtual Private Networking With IPSec Connections 
339  ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2
8. Click the Apply button.
Your settings are saved. The VPN Policies screen displays the IPv4 settings with the 
new, automatically generated VPN policy in the List of VPN Policies table.
9. On the remote gateway, configure a VPN policy that allows connection to the VPN firewall.
This VPN tunnel will use the 
following local WAN InterfaceSelect a WAN interface from the menu.
The VPN...

Set Up Virtual Private Networking With IPSec Connections 
340 ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2 
The configuration steps depend on the remote gateway.
10. On the VPN firewall, activate the IPSec VPN connection:
a.Select VPN > Connection Status.
b. Locate the policy in the table and click the Connect button.
The IPSec VPN connection becomes active.
Note:If you use an FQDN as the tunnel endpoint address on the VPN firewall, 
if the Dynamic DNS service is slow to update its servers...

Set Up Virtual Private Networking With IPSec Connections 
341  ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2
To set up an IPv6 gateway-to-gateway VPN tunnel using the VPN Wizard:
1. On your computer, launch an Internet browser.
2. In the address field of your browser, enter the IP address that was assigned to the VPN 
firewall during the installation process.
The VPN firewall factory default IP address is 192.168.1.1.
The NETGEAR Configuration Manager Login screen displays.
3. In the Username...

Set Up Virtual Private Networking With IPSec Connections 
342 ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2 
8. Enter the settings as described in the following table.
SettingDescription
About VPN Wizard
This VPN tunnel will connect 
to the following peersSelect the Gateway radio button. 
The local WAN port’s IP address or Internet name displays in the End Point 
Information section.
Connection Name and Remote IP Type
What is the new Connection 
Name?Enter a descriptive name for the connection....

Set Up Virtual Private Networking With IPSec Connections 
343  ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2
9. Click the Apply button.
Your settings are saved. The VPN Policies screen displays the IPv6 settings with the 
new, automatically generated VPN policy in the List of VPN Policies table.
10. On the remote gateway, configure a VPN policy that allows connection to the VPN firewall.
The configuration steps depend on the remote gateway.
This VPN tunnel will use the 
following local WAN...

Set Up Virtual Private Networking With IPSec Connections 
344 ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2 
11. On the VPN firewall, activate the IPSec VPN connection:
a.Select VPN > Connection Status.
b. Locate the policy in the table and click the Connect button.
The IPSec VPN connection becomes active.
Note:If you use an FQDN as the tunnel endpoint address on the VPN firewall, 
if the Dynamic DNS service is slow to update its servers when your 
DHCP WAN address changes, the VPN tunnel fails...

Set Up Virtual Private Networking With IPSec Connections 
345  ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2
Figure 10. Example of an IPv4 client-to-gateway IPSec VPN connection
The VPN firewall supports client connections with the NETGEAR ProSAFE VPN Client, which is 
an application that you can install on a computer.
The VPN firewall is bundled with a single-user license of the NETGEAR ProSAFE VPN Client 
software (VPN01L). For information about the NETGEAR ProSAFE VPN Client, including...

Set Up Virtual Private Networking With IPSec Connections 
346 ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2 
To set up the VPN firewall for a client-to-gateway VPN tunnel using the VPN Wizard:
1. On your computer, launch an Internet browser.
2. In the address field of your browser, enter the IP address that was assigned to the VPN 
firewall during the installation process.
The VPN firewall factory default IP address is 192.168.1.1.
The NETGEAR Configuration Manager Login screen displays.
3. In...

Set Up Virtual Private Networking With IPSec Connections 
347  ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2
7. Enter the settings as described in the following table.
SettingDescription
About VPN Wizard
This VPN tunnel will connect 
to the following peersSelect the VPN Client radio button. 
The default remote FQDN (remote.com) and the default local FQDN 
(local.com) display in the End Point Information section.
Connection Name and Remote IP Type
What is the new Connection 
Name?Enter a...

Set Up Virtual Private Networking With IPSec Connections 
348 ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2 
8. Click the Apply button.
Your settings are saved. The VPN Policies screen displays the IPv4 settings with the 
new, automatically generated VPN policy in the List of VPN Policies table.
This VPN tunnel will use the 
following local WAN InterfaceSelect a WAN interface from the menu.
The VPN tunnel uses the WAN interface as the local endpoint.
To enable VPN rollover, select the Enable...