Netgear Netgar VPN FIrewall FVS336Gv2 Reference Manual

Protect Your Network 
330 ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2 
If you did not change the domain or were not assigned a domain, leave the menu 
selection at geardomain.
5. Click the Login button.
The Router Status screen displays.
6. Select Security > Port Triggering. 
The Port Triggering screen displays.
7. Click the Status option arrow in the upper right.
The Port Triggering Status pop-up screen displays.
The pop-up screen displays the status of the port triggering rules.
Enable...

Protect Your Network 
331  ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2
If you did not change the domain or were not assigned a domain, leave the menu 
selection at geardomain.
5. Click the Login button.
The Router Status screen displays.
6. Select Security > UPnP.
The UPnP screen displays.
The UPnP Portmap Table shows the IP addresses and other settings of UPnP devices 
that accessed the VPN firewall and that were automatically detected by the VPN firewall:
•Active. A Yes or No indicates if...

Protect Your Network 
332 ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2 
Click the Refresh button. The content of the UPnP Portmap Table refreshes. Any UPnP 
devices that accessed the VPN firewall and that were automatically detected by the VPN 
firewall display in the UPnP Portmap Table. 

332
8
8.   Set Up Virtual Private Networking 
With IPSec Connections
This chapter describes how to use the IP security (IPSec) virtual private networking (VPN) 
features of the VPN firewall to provide secure, encrypted communications between your local 
network and a remote network or computer. The chapter contains the following sections:
•Dual WAN Port Systems
•Use the IPSec VPN Wizard for Client and Gateway Configurations
•Test the Connection and View Connection and Status Information
•Manage IPSec VPN...

Set Up Virtual Private Networking With IPSec Connections 
333  ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2
Dual WAN Port Systems
If two WAN ports are configured for either IPv4 or IPv6, you can enable either auto-rollover 
mode for increased system reliability or load balancing mode for optimum bandwidth 
efficiency. The selection of the WAN mode determines how you must configure the VPN 
features.
If the WAN ports function in auto-rollover mode, you must use fully qualified domain names...

Set Up Virtual Private Networking With IPSec Connections 
334 ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2 
The following table summarizes the WAN addressing requirements (FQDN or IP address) for 
a VPN tunnel in either dual WAN mode.
Use the IPSec VPN Wizard for Client and Gateway 
Configurations
You can use the IPSec VPN Wizard to configure multiple gateway or client VPN tunnel 
policies.
The following sections provide information about how to create IPSec VPN connections with 
the IPSec VPN...

Set Up Virtual Private Networking With IPSec Connections 
335  ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2
algorithm, and encryption. The settings that the VPN Wizard uses are based on the 
recommendations of the VPN Consortium (VPNC), an organization that promotes 
multivendor VPN interoperability.
Tip:To ensure that VPN tunnels stay active, after completing the wizard, 
manually change the VPN policy to enable keep-alives. The VPN 
firewall periodically sends ping packets to the host on the...

Set Up Virtual Private Networking With IPSec Connections 
336 ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2 
The Router Status screen displays.
6. Select VPN > IPSec VPN > VPN Wizard.
The VPN Wizard screen displays the IPv4 settings.
7. Click the VPN Wizard default values option arrow in the upper right.
The VPN Wizard default values pop-up screen displays. The default values are the same 
for IPv4 and IPv6.
Create an IPv4 Gateway-to-Gateway VPN Tunnel with the 
Wizard
The following figure...

Set Up Virtual Private Networking With IPSec Connections 
337  ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2
Figure 8. Example of an IPv4 gateway-to-gateway IPSec VPN connection
To set up an IPv4 gateway-to-gateway VPN tunnel using the VPN Wizard:
1. On your computer, launch an Internet browser.
2. In the address field of your browser, enter the IP address that was assigned to the VPN 
firewall during the installation process.
The VPN firewall factory default IP address is 192.168.1.1.
The...

Set Up Virtual Private Networking With IPSec Connections 
338 ProSAFE Dual WAN Gigabit WAN SSL VPN Firewall FVS336Gv2 
7. Enter the settings as described in the following table.
SettingDescription
About VPN Wizard
This VPN tunnel will connect 
to the following peersSelect the Gateway radio button. 
The local WAN port’s IP address or Internet name displays in the End 
Point Information section.
Connection Name and Remote IP Type
What is the new Connection 
Name?Enter a descriptive name for the connection....