Netgear Dm111pspv2 Adsl2 Plus Ethernet Modem User Manual

Troubleshooting
71  Broadband ADSL2+ Modem DM111PSPv2
-     Make sure that the LAN port LED is on. If the LED is off, follow the instructions in 
Ethernet LED Is Off on page 67.
-     Check that the corresponding link LEDs are on for your network interface card 
and for the hub ports (if any) that are connected to your workstation and modem.
•     Wrong network configuration
-     Verify that the Ethernet card driver software and TCP/IP software are both 
installed and configured on your PC or...

Troubleshooting72
Broadband ADSL2+ Modem DM111PSPv2 
•     
Check the Ethernet connection between the computer and the  modem. The Ethernet LED 
should light up to show your connection.
•     Your computer’s IP address is on the same subnet as the  modem.
  If you are using the 
recommended addressing scheme, your computer’s address should be in t\
he range 
192.168.0.2 to 192.168.0.254.
•     If the computer IP address is 169.254.x.x, recent versions of Windows an\
d Mac OS  generate and assign an IP...

Troubleshooting
73  Broadband ADSL2+ Modem DM111PSPv2
To reload the firmware:
1. If you already have the firmware file on your PC, go directly to step 2. If you do not have 
the firmware file on your PC, obtain the firmware from the NETGEAR support site at 
http://www.netgear.com/support through another working Internet connection.
2. Click Browse.
3. Navigate to the firmware file. 
4. Click Upgrade. A progress bar displays. The reload takes about 5 minutes to complete. 
When the firmware recovery is...

74
A
A.   Technical Specifications
This appendix includes the factory default settings, technical specifications for the modem, 
related documents, and instructions for wall-mounting the unit.
This appendix contains the following sections:
•     Factory Settings 
•     Technical Specifications  

Technical Specifications75
Broadband ADSL2+ Modem DM111PSPv2
Factory Settings
You can return the modem to its factory settings. Use the end of a paper\
 clip or a similar 
object to press and hold the 
Restore Factory Settings button for at least 7 seconds. The 
modem resets, and returns to the factory settings.
 Your device will return to the factory 
settings shown in the following table.
FeatureDefault Behavior
Modem Login User login URL http://www.routerlogin.net or http://www.routerlogin.com
User...

Technical Specifications76
Broadband ADSL2+ Modem DM111PSPv2
Technical Specifications
FeatureSpecification
Data and routing protocols TCP/IP, RIP-1, RIP-2, DHCP, PPPoE or PPPoA, RFC 1483 Bridged or 
Routed Ethernet, and RFC 1577 Classical IP over ATM
Power adapter (North America) 120V, 60 Hz, input
12 V @1.0A output
Dimensions 5.79 x3.76 x 1.2 inches (47 x 95.5 x 30.5 mm)
Weight 0.42 lbs (190 grams)
Operating temperature 0° to 40° C (32º to 104º F)
Operating humidity 10% to 90% relative humidity,...

77
B
B.   Notification of Compliance
NETGEAR Wired Products
Regulatory Compliance Information
This section includes user requirements for operating this product in accordance with National 
laws for usage of radio spectrum and operation of radio devices. Failure of the end-user to 
comply with the applicable requirements may result in unlawful operation and adverse action 
against the end-user by the applicable National regulatory authority.
This products firmware limits operation to only the channels...

Notification of Compliance
78 Broadband ADSL2+ Modem DM111PSPv2
•     This device must accept any interference received, including interference that may cause 
undesired operation.
FCC Radio Frequency Interference Warnings & Instructions
This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. This 
equipment...

Notification of Compliance
79 Broadband ADSL2+ Modem DM111PSPv2
For GNU General Public License (GPL) related information, please visit 
http://support.netgear.com/app/answers/detail/a_id/2649. 

80
Index
A
AC power adapter input 8
accessing remote computer 29
addresses, DNS 23
ADSL microfilters 10
cabling 11
described 10
ADSL port 8
ADSL settings 24
ADSL statistics, viewing 50
alerts, emailing 41
Application Level Gateway (ALG), disabling 55
attached devices, viewing 51
automatic firmware checking 44
automatic Internet connection 20
B
back panel 8
backing up configuration 47
Basic Settings screen
described 22
manual setup 21
blocking
content and services 27
keywords, examples 28
box contents 7...