NEC Xl 6500 Projector User Manual

71
Execute Mode
Enables you to select connecting with the switcher ISS-6020 and
view the projector address on the screen.
To do, follow the steps below.
1. Press the ADJUST button to display the Adjustment menu.
2. Use the CURSOR 
or button to select Ò8. Set OptionÓ menu.
Press ENTER.
3. Use the CURSOR 
or button to select Ò4. Execute ModeÓ
menu. Press ENTER.
Proceed to the following steps.
This setting explains how the projector is used with the ISS-6020/
ISS-6020G Switcher.
1Use the CURSOR
orbutton to...

72 3.OPERATION
Each projector needs its own unique address in the case of a serial
connection of projectors. Up to 64 addresses can be set.
Proceed as follows:
1Use the CURSOR
orbutton to highlight the Ò2/PJ AddressÓ
line. Press ENTER to display the ÒAddressÓ menu.
2Enter the address number using the INPUT button and press
ENTER.
¥ If you have made a mistake, press END to return to the ÒOP-
TIONÓ menu, then start again.
NOTE: Enter the address number Ò01Ó when only one projector
is used.
n PJ Address...

73
m  Addressing the Remote Control Unit
When changing the projector address, ensure that the projector
address respond to the remote control address, otherwise you cannot
operate the projector using the remote control.
To specify the remote control address, proceed as follows:
1) Press and hold the CTL button then press the ADDRESS button
to access the RC UNIT address mode.
¥ The current remote control address is displayed on the remote
control address screen. (When the current remote control
address is...

74
3.OPERATION
Help Menu
Provides information about operation and adjustment procedures or
the set information.
To view the information:
Press OPERATE or ADJUST button then select ÒHelpÓ from the
Task bar and press ENTER. The Help menu will be displayed.-Help-
1. Help
2. Topics
3. Set Information
n Help
Provides information how to use the Help.
To view the Help menu, use the CURSOR 
or button to select
Ò1. HelpÓ menu and press ENTER.
n Topics
Provides you information of a various items explaining...

75
Others
n Test Patterns
Test Pattern
Off
Flat Field
Ramp
Contrast Checkerboard
Cross Hatch
Gray Bars
Small Checkerboard
Black Flat Field
This projector will generate a selection of test signals.
Seven kinds of internal test patterns can be selected from the Test
Pattern menu.
To display the Test Pattern menu, proceed as follows:
1. Press the TEST button on the remote control.
¥ The Test Pattern menu will be displayed.
¥ When END is pressed, the Test Pattern menu will disappear.
2 User the CURSOR 
or...

76 3.OPERATION
n Normal, Load, and Cancel Function
Adjustment settings can be returned to the factory preset level,
previously stored level, or can be canceled.
To return to the standard level (Normal):
1. Press the NORMAL button.
The confirmation message is displayed.
2. Use the CURSOR 
or button to select Yes.
A confirmation message is displayed.
3. Press ENTER.
The Normal function is performed.
If you select ÒNoÓ, you will exit this mode suspending current
status.
Test Pattern
YesNoWhite Balance...

77
n To cancel the adjustment data (Cancel):
Memory
LoadCancel
Cancel
YesNoWhite Balance
-  Color Temperature -
Data Cancel?
1. Press and hold the CTL button then press the NORMAL button.
¥ The Memory menu is displayed.
2. Use the CURSOR 
or button to select Cancel.
¥ A confirmation message is displayed.
3. Use the CURSOR 
or button to select Yes.
¥ If you select No, you will exit this mode suspending current
status.
4. Press ENTER.
¥ The CANCEL function is performed.3.OPERATION 

78
1234567
1234567
1234567
1234567
1234567
1234567
1234567 4.SPECIFICATIONS
Projection Type : 3Chip DMD TM High light output projector.
Projection System : 3chip DMD TM , 1 Lens
Display Orientation : Front Floor , Rear Floor ,
Front Ceiling , Rear Ceiling
Lamp Type : Bulb type 1.6 KW Xenon Lamp
Shooting offset : Common lens for both XL-3500 and XL-6500
Fixed lens ........................................... 0±150 pixels
Zoom lens .......................................... 0
Lens for XL-6500 only...

79
Convergence limits : Within one pixel
Set-up signal : Gray bars signal , Cross hatch signal , Flat field ,
Black flat field, Contrast checker board, Small checker board, and Ramp
Power supply : AC 200V - 240V
Power consumption : 2.4KW ( MAX)
Input current : 13.0 A(MAX)
Safety and regulation
UL : Meet UL 1950
CSA : Meet CSA 950
FCC : Meet FCC class A
DHHS : Approved
DOC : Meet
Meet EMC Directive
  EN55022  : Meet(Radiation)
  EN55082-2  : Meet(Immunity)
  EN61000-3-2, EN61000-3-3  : Meet(Disturbance)...

80
Code                       Message
1234567
1234567
1234567
1234567
1234567
1234567 5.APPENDIX
Message List
A1PS PROTECT ERROR (Overload or failure in the mains power supply)
A2POWERGOOD ERROR (Insufficient voltage of +5V(D) or DLP5V in the mains power supply)
C0~CFCOMUNICATION ERROR (Communication setting errors in conjunction with switcher and PC control)
D0SIGNAL UNLOOK (Instability or failure in synchronization)
E0FAN STOP ERROR (Fan stoppage)
ECFLASH MEMORY ERASE ERROR (Error in system PWB)...