NEC Xl 6500 Projector User Manual

61
SLOT–01
SLOT–02
SLOT–03
SLOT–04
SLOT–05
SLOT–06
SLOT–07
SLOT–08
SLOT–09
SLOT–10 MASTER
3Use the CURSORorbutton to select an input and then
press the ENTER button.
When used in stand alone operation:
The default input screen will be displayed.
Use the CURSOR
orbutton to select  an input and press
ENTER.
When used with a single Switcher:
The ÒMASTERÓ slot menu will be displayed.
Use the CURSOR
orbutton to select the desired slot
number Ò1Ó through Ò10(0)Ó and then press ENTER.
When used with two or more...

62 3.OPERATION
]
This function is used to select the S-video signal detection mode.
This  allows identifying of the S-video signals with different aspect
ratio: squeeze or  full mode(16 : 9) and letter box (4 : 3) signals.
To set, proceed as follows:
1Use the CURSOR
orbutton to select the ÒS-Video Mode
SelectÓ item, then press ENTER to display the ÒS-Video Mode
SelectÓ menu.
n S-Video Mode Select
-Setting Mode-
1. PJ Orientation
2. Default Source Select
3. S-Video Mode Select
4. Video System Select
5....

63 This function is used to select the NTSC 3.58, NTSC 4.43, PAL or
SECAM video standard.
To select any one of the video standards, proceed as follows:
1Use the CURSOR
orbutton to select the ÒVideo System
Select Ó item, then press ENTER to display the ÒVideo System
Select Ó menu.
n Video System Select
-Setting Mode-
1. PJ Orientation
2. Default Source Select
3. S-Video Mode Select
4. Video System Select
5. Auto Data Store
6. Option Terminal Speed
7. Uniformity Switching
Setting Mode
PJ Orientation...

64 3.OPERATION
This feature allows you to select two ways to store settings; auto-
matically and manually.
After ÒEnableÓ is selected in the Auto Data Store menu, all projector
settings are stored in the projectors memory automatically. To set
this feature, proceed as follows:
1Use the CURSOR
orbutton to select the ÒAuto Data StoreÓ
item on Page 2, then press ENTER to display the ÒAuto Data
StoreÓ menu.
n Auto Data Store
-Setting Mode-
1. PJ Orientation
2. Default Source Select
3. S-Video Mode Select
4....

65
n Option Terminal Speed
This feature allows you to set baud rate of the OPTION terminal
from 4800 to 38400 bps.
NOTE:
¥ The baud rate of the OPTION terminal defaults to 38400 bps at the
factory.
¥ Make sure that the baud rate of the OPTION terminal matches that
of operating of the connected equipment.
To change the baud rate of the OPTION terminal, proceed as follows:
1Use the CURSOR 
 or  button to select the ÒOption
Terminal SpeedÓ item, then press ENTER to display the ÒOption
Term Boad RateÓ menu....

66 3.OPERATION
n Uniformity Switching
Enables you to enable or dasable the uniformity white and edge
blending features.
1Use the CURSOR 
 or  button to select the ÒUniformity
SwitchingÓ item, then press ENTER.
2Use the CURSOR 
 or  button to select the ÒWhite Unifor-
mity or Edge Blend.Ó item, and select Disable or Enable, then
ENTER.
-Setting Mode-
1. PJ Orientation
2. Default Source Select
3. S-Video Mode Select
4. Video System Select
5. Auto Data Store
6. Option Terminal Speed
7. Uniformity Switching...

67
There are two modes of operations for the on-screen display. With
AUTO mode, the on-screen display will automatically switch off
after three through ten seconds. In the MANUAL mode, the display
must be manually turned off with the DISPLAY button on the full
function remote control each time it appears.
NOTE: Pressing DISPLAY with CTL will select the non on-screen
mode; pressing DISPLAY with CTL again will cancel this mode.
Even if the on-screen display may be turned off with CTL and
DISPLAY, any...

68
3.OPERATION
2Use the CURSOR
orbutton to select either ÒAutoÓ or
ÒManualÒ and press ENTER.
Items to select
¥ Auto ......... The on-screen menu display appears when the
buttons on the remote control, or the controls on
the rear panel are pressed. The on-screen display
will turn off at a preselected time.
The OFF TIME is specified in seconds up to a
maximum of 30 seconds.
Select your desired time (3-30 seconds) from the
OFF TIME menu.
¥ Manual .... The on-screen menu display appears when the
buttons on...

69 The current year, month, date and time are displayed on the top of
the screen.
Proceed as follows:
1Use the CURSOR
orbutton to highlight the ÒDate, Time,
PresetÓ item. Press ENTER to display the ÒDate, Time PresetÓ
menu.
2Use the CURSOR
orbutton to select any one of the two
items: Date, and Time.
3Type the date and time. Then press OK.
n Date, Time Preset
-Menu Mode-
1. Message Time
2. Date, Time Preset
3. Display Item Set
Menu Mode
Message Time
Date, Time Preset
Display Item Set 
Date [Off   ]
[Off...

70 3.OPERATION
This feature allows you to display the items : date, time, input signal,
source name, address, and new signal on the top of the screen.
1Use the CURSOR
orbutton to highlight the ÒDisplay Item
SetÓ menu. Press ENTER.
n Display Item Set
Menu Mode
Message Time
Date, Time Preset
Display Item Set 
Date [Off   ]
[Off   ]
[Off   ]
[Off   ]
[Off   ]
[Off   ]
New SignalTime
Input Signal
Soutce Name
Address[Auto 10 Sec     ]
 Jan/DD/YYYY
 HH:MM:SS
-Menu Mode-
1. Message Time
2. Date, Time Preset
3....