NEC Visualink 128/384 User Guide

							NDA-24230 Issue 2.0Page 4-23
VisuaLink 128/384 User Guide Chapter 4
4.3 Software Setup
When you first turn on your VisuaLink, there will be an initial configuration 
screen.  These configuration screens will have to be completed before your system 
becomes operational.
Start up configuration screens
The following are the startup screens that will be active on first power up or acti-
vated on demand by the user after choosing the Environmental initialize. 
Welcome Screen:  
This is a welcome screen for the User.
Vi s u a L i n k
Thank you for purchasing one of the most
simple and portable video conferencing systems 
available.
We will now show you how to set up your system.  
This will only have to be done once.
NOTE: If remote controller doesn’t work, make 
sure the switch setting of D30 camera IR 
out is ON.  Switch is located on the 
bottom of the camera.
 Click here to continue
    Configure laters
Note is yellow. 
						

							Page 4-24NDA-24230 Issue 2.0
Chapter 4 VisuaLink 128/384 User Guide
Remote Controller Directions: 
Gives some general directions for configure the VisuaLink system.  Using the 
Remote controller highlight the NEXT option to advance to the configure screen 
or press the lower portion of the CAMERA CONTROL key to highlight the 
Configure Later to advance to the normal ICON screens.  If you choose to 
configure later, the system will have to be programmed with My numbers and 
SPID’s in order to work correctly.
4.4 Setting Up your 
ISDN Line 
InformationThe following is a description of BRI Line setup
Part 1- Remote Controller Location
-  Locate the CAMERA control.
The CAMERA control key  is the BLUE round 
key.  Use this key to move the Cursor 
up/down and Left/Right in the Configuration
Screens.
-  Locate the ENTER key on the Wireless remote
   controller.
Use the ENTER key to confirm selections 
and store information.
   Next screen 
     Prior screen
s
Part 2- Setting up Your ISDN Line 
Introduction:
When ordering BRI service,  you will usually get 
2 My numbers and 2 SPID numbers per BRI.  
A SPID normally consists of the user’s 3 digit  
area code, 7 digit ISDN telephone number, 
followed by a 0101. Ex:
      MY Number 1: 9727195854
      SPID 1:  97271958540101 
Note: The VisuaLink 128 requires 2 My numbers 
and 2 SPID #, while the VisuaLink 384 
requires 6 My numbers and 6 SPID #.
 Next screen
    Prior screen
s
Note is yellow. 
						

							NDA-24230 Issue 2.0Page 4-25
VisuaLink 128/384 User Guide Chapter 4
Video Number 1 Screen’s
Using the number pad of the wireless remote enter My Number with area code 
and SPID numbers associated to Line  (BRI 1).  Each BRI will have My numbers 
labeled #1 and #2 and two SPID’s .  All four numbers must be entered.  Choose 
NEXT when complete.  
Note:
“PROCEED TO STEP 2” will only be shown on the VisuaLink 128 system.  
VisuaLink 384 will show “ Proceed to Line 2 Setup”   
Step 1--Enter My Number and SPID for BRI LINE 1
     My Number 1:
 []
     SPID 1:
    [ ]
    My Number 2:
    [ ]
    SPID 2:
    [ ]
Next screen
Prior screen
Press  ENTER after choosing each item
s
Step 1--Enter My Number and SPID for BRI LINE 1
     My Number 1:
    [9727195854]
     SPID 1:
    [97271958540101]
    My Number 2:
 [9727195855]
    SPID 2:
    [ ]
Next screen
Prior screen
Press  ENTER after choosing each item
s 
						

							Page 4-26NDA-24230 Issue 2.0
Chapter 4 VisuaLink 128/384 User Guide
Video Number 2 Screens:
Using the number pad of the wireless remote enter My Number with area code 
and SPID numbers associated to Line  (BRI 2).  Each BRI will have My numbers 
labeled #1 and #2 and two SPID’s .  All four numbers must be entered.  Choose 
NEXT when complete.
Note:
  This screen will only appear on the VL 384 system.
Step 1--Enter My Number and SPID for BRI LINE 2
    My Number 1:
 []
    SPID 1:
    [ ]
    My Number 2:
    [ ]
    SPID 2:
    [ ]
Next screen
Prior screen
Press  ENTER after choosing each item
s 
						

							NDA-24230 Issue 2.0Page 4-27
VisuaLink 128/384 User Guide Chapter 4
Video Number 3 Screens:
Using the number pad of the wireless remote enter My Number with area code 
and SPID numbers associated to Line  (BRI 3).  Each BRI will have My numbers 
labeled #1 and #2 and two SPID’s .  All four numbers must be entered .  Choose 
NEXT when complete.
Note: 
 This screen will only appear on the VL 384 system.
4.5 Optional User 
Settings:The following is a description for Optional Setting screen.
Step 1--Enter My Number and SPID for BRI LINE 3
    My Number 1:
 []
    SPID 1:
    [ ]
    My Number 2:
    [ ]
    SPID 2:
    [ ]
Next screen
Prior screen
Press  ENTER after choosing each item
s
Part 3 - Optional User Settings
Introduction:
Site Name: Name identification for your 
location.  Name is displayed on 
far-end monitor when site is viewed.
Password: Required to gain access to the 
VisuaLink configuration screens.
Time setting: Sets the internal clock for the 
Vi s u a L i n k .
  Next screen 
     Prior screen
s 
						

							Page 4-28NDA-24230 Issue 2.0
Chapter 4 VisuaLink 128/384 User Guide
Optional information:
You may enter this optional information.  The name you enter makes it easy for 
users to identify this particular VisuaLink.  The name can be up to 20 characters 
long.  The Password is the password needed to be entered when selecting the 
Utilities ICON.  After entering the optional information select the NEXT to 
advance to the next screen.  
Application Screen’s
Using the number pad on the wireless remote controller select the application 
which the VisuaLink is installed.  Your answer to this question will automatically 
configure the internal parameters for the following:
Step 1-  Optional User Settings
Your Site Name        
[                           ]
Password  [          ]
Time Setting 
[12/1/1998   10:50]
Time Display:  
Auto Power Save:  
Next screen
Prior screen
Press ENTER after choosing each items
Item Rollabout/Other Data Conference Gateway Desktop
Serial Port 1 Camera EVI-D30 T.120 Camera Camera
Serial Port 2 Console Console Console Console
Audio Mode G.722 G.728 G.722 G.722
MLP 4.0 24.0 4.0 4.0
Answer Mode Auto Auto Auto Manual
LSD 1.2 Off 1.2 1.2
Ext. Remote Auto Off Off Off
H.263 Off Off Off Off
Lip Sync On On On On 
						

							NDA-24230 Issue 2.0Page 4-29
VisuaLink 128/384 User Guide Chapter 4
Congratulations Screen
The VisuaLink is now setup for the configuration you have entered.  Press the 
ENTER
 button on the REMOTE CONTROLLER
, the VisuaLink will display a 
blue screen and recycle.  The VisuaLink should will power up to a normal state.   
You may begin to use the video conferencing system immediately.
Note:
If there are no My Numbers entered in the configuration the VisuaLink 
will display the Start Up screens.
Step 2—Optional User Settings
Key in the number of one of the following 
applications.
Applications:
1.  Rollabout/Other
2.  Data Conference
3.  Gateway
4.  Desktop
Press CANCEL to page back
Congratulations, you have just finished setting 
up your VisuaLink system.  
For VisuaLink software updates and general 
VisuaLink knowledge, visit the NEC Knowledge 
base web site at : 
http://www.cng.nec.com  or
http://www.ilibrary.com/phoenix/ntachome.nsf 
/homepagenav?opennavigator
- You may begin to use the video conferencing 
system immediately.
- Press ENTER to activate your configuration.  
Press CANCEL to page back 
						

							Page 4-30NDA-24230 Issue 2.0
Chapter 4 VisuaLink 128/384 User Guide
Powering Up Screen
Changing the configuration
It is important that the CODEC is set up with a local number and SPID numbers.  
If the unit is not setup with a local number (my number) and SPID, the unit will 
not allow for dialing and receiving of video calls.  If you have entered these 
numbers in the Start Up configuration, you may ignore this section.  If the 
VisuaLink environment has changed, such as the phone number have changed, 
you must reconfigures the numbers in the VisuaLink.             
America, Inc.
         VisuaLink
Powering Up
Ver .22.02.37 
						

							NDA-24230 Issue 2.0Page 5-1
VisuaLink 128/384 User Guide Chapter 5
Chapter 5  System Parameter/Environment Setting
System parameter sets the operation conditions of the VisuaLink 128 or 
VisuaLink 384.  Environment setting can be set such as camera class, audio 
related, data related, line related and local office status.  Loopback feature can be 
used as a maintenance feature.
Note 1:
Make system parameter changes when the system is not connected.
Note 2:
Depending on the setting for audio, data speed and bit rate, and the video 
has the possibility for not being transmitted.  Please refer to Appendix A: 
Audio/Data/Video Bit Rate Assignment Table
 for bit rate assignment of 
audio, data, video bit rate.
5.1 Environment 
Setting Menu5.1.1  Set an environment
¬
Press the MENU
 button to display the MAIN MENU
.
s
Setting the PIP parameter.MENU 
						

							Page 5-2NDA-24230 Issue 2.0
Chapter 5 VisuaLink 128/384 User Guide
Á
Move the cursor with the CAMERA CONTROL 
button to the 
ENVIRONMENT SETTING
 icon.
Â
Press the ENTER
 button.
The system will not operate correctly if the environment setting are incorrect.  
Therefore, the system has a password so that only the person in charge of 
controlling video conference can change the settings.  Factory default password is 
1234
.
s
Setting environments.
CAMERA
CONTROL
Please input password.
               
          [                   ]
Press ENTER after inputting password.
ENTER