NEC Visualink 128/384 User Guide
Have a look at the manual NEC Visualink 128/384 User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
NDA-24230 Issue 2.0Page 4-13 VisuaLink 128/384 User Guide Chapter 4 4.2.5 VisuaLink System Procedures The following are the steps and procedures for the installation of the VisuaLink 128 or VisuaLink 384. STEP ACTION DRAWING 1. Locate and unpack the Cabinet box. 2. Locate Power Strip at botton-left (looking through the front) of cabinet and feed power cable through the power opening at rear of cabinet. 3. Plug power strip power cable into AC outlet. Make sure the ON/OFF switch on the upper right outside of the cabinet is in the OFF position. Note: The power switch will be lite when in the ON position. Powerstr ip Power Switch
Page 4-14NDA-24230 Issue 2.0 Chapter 4 VisuaLink 128/384 User Guide 4. Remove Monitor from monitor box. 4a. Place TV monitor on top of cabinet. 5. Locate monitor power cable and feed through the cable opening at the top of cabinet. 6. From inside the cabinet, plug the monitor power cable into power strip. STEP ACTION DRAWING 12 VIDE O I NS- VIDEO VI DEO AUDI OL MONO RAUDI O OUT (VAR/FIX) Power Cable Powe r st r i p
NDA-24230 Issue 2.0Page 4-15 VisuaLink 128/384 User Guide Chapter 4 7. Locate the cable bundle and remove from packing box. The cable bundle contains two (2) 5 in. (12 cm.) Velcro strips. Use these strips to mount the camera to the top of the monitor. 8. Locate the camera box and remove camera. 9. Set the IR switch on the Sony D30 camera to the ON position. The IR switch is located on the bottom of the Sony D30 camera. This will allow for the Sony Camera to receive the IR codes from the VisuaLink remote controller and transmit them to the VisuaLink Codec for control. Mount the camera on the top of monitor, using the Velcro strips. Make sure the front of the camera is flush with the front of the monitor and the camera is centered. STEP ACTION DRAWING Foam Inserts Polyethylene Bag Packing Carton Velcro Strips IR OUT Switch
Page 4-16NDA-24230 Issue 2.0 Chapter 4 VisuaLink 128/384 User Guide 10. Locate the camera power cable. Plug the camera power cable into the power strip in cabinet, then feed cable through top of cabinet and plug into the rear of the camera. 11. Locate the VisuaLink 128 or VisuaLink 384 and remove from packing box. 12. Place the VisuaLink 128 or VisuaLink 384 on the second shelf of the cabinet. STEP ACTION DRAWING 12 VIDE O I NS- VI DEO VI DEO AUDI OL MONO RAUDI O OUT (VAR/FIX) Video Power Cable Powe r Cable Hole Polyethylene Bag Foam Inser ts Packing Carton POWER H EADSET POWERLINEB1 B2
NDA-24230 Issue 2.0Page 4-17 VisuaLink 128/384 User Guide Chapter 4 13. Locate the VisuaLink 128 or VisuaLink 384 power cable. Plug cable into power strip at bottom of cabinet and feed cable through cable slot in rear of second shelf. Plug second end of power cable into power input at rear of the VisuaLink 128 or VisuaLink384. 14. The cable bundle is labeled at the ends of the various connectors. Plug these connectors into the appropriate devices (camera/monitor) and feed down through opening at top of cabinet. See Figure 4-1 and Figure 4-2. Note: Connector layout could vary by manufacture. Please consult their documentation if connector layout is different. STEP ACTION DRAWING Power Plug Connection + + ++ +DC I N 5 V+ - Serial1 Serial2/RMT O U T I N VIDEO2 VIDEO1 AUDIO ++TEL S/T LINEMIC1 MIC2 MI C3 VisuaLink 128 Rear + + ++ +DC IN 5V+ - Serial1 Serial2/RMT O U T I N V IDEO2 VIDEO1 AUD IO ++TEL S /T LINE 1 S/T LINE 2 S/T LINE 3MI C1 MIC 2 MIC3 VisuaLink 384 Rear Power Plug Connection VISCA In 12 VIDEO IN S-VIDEO VIDEO AUDIOL MONO RAUDIO OUT (VAR/FIX) Camera Control Sony D30 Camera Vout CAMERA MONITOR VHF/UHF Monitor Vin Monitor Audio L(Cable) (Cable)(Cable) (Cable)
Page 4-18NDA-24230 Issue 2.0 Chapter 4 VisuaLink 128/384 User Guide 15. Inside the cabinet, connect the other ends of the cable bundle to the VisuaLink 128 or VisuaLink 384. See Figure 4-1 and Figure 4-2. 16. Locate and unpack the microphone and connect the 3 1/2 inch plug into the VisuaLink connection marked MIC1. String the MIC cable out of the rear of the cabinet. Connect the other end of the cable into the Microphone and place on table. STEP ACTION DRAWING + + ++ +DC I N 5 V+ - Serial1 Serial2/RMT O U T I N VIDEO2 VIDEO1 AUDIO ++TEL S/T LINEMIC1 MIC2 MI C3 Serial 1VisuaLink 128/384 (Cable) Video In (Cable) VisuaLink 128 Rear Video Out (Cable) Audio Output (Cable) + + ++ +DC IN 5V+ - Serial 1 Serial2/RMT O U T I N VIDEO2 VIDE O1 AUDIO ++TEL S/T LINE 1 S/T LINE 2 S/T LINE 3MIC1 MIC2 MI C3 VisuaLink 384 Rear Video Out (Cable)Audio Output (Cable) Serial 1 (Cable)VisuaLink 128/384 Video In (Cable) + + ++ +DC I N 5 V+ - Serial1 Serial2/RMT O U T I N VIDEO2 VIDEO1 AUDIO ++TEL S/T LINEMIC1 MIC2 MI C3 MIC1 + + ++ +DC IN 5V+ - Serial1 Serial2/RMT O U T I N VIDEO2 VIDE O1 AUDIO ++TEL S/T LINE 1 S/T LINE 2 S/T LINE 3MIC1 MIC2 MI C3 VisuaLink 384 Rear VisuaLink 128 Rear MIC1
NDA-24230 Issue 2.0Page 4-19 VisuaLink 128/384 User Guide Chapter 4 17. If an NT1 device has been purchased, locate the device and unpack. Note 1: If an NT1 was not purchased go to Step 23. Note 2: Three NT1 are used for the VL384. 18. Locate the dip switch on the rear of the NT1 and set all to the ON position. 19. Place the NT1 or the three NT1s on the second shelf, to the right of the VisuaLink 128 or VisuaLink 384. 20. Locate the NT1 power cable. Plug cable into power strip at bottom of cabinet and feed cable through cable slot in rear of second shelf. Plug second end of power cable into power input at rear of the NT1. STEP ACTION DRAWING Polyethylene Bag Foam Inser ts Packing Carton 1 23 45ON 1234 5ONPOWER U NT1 REAR POWER HEADSET POWERLINEB1 B2 NT1 VisuaLink 128/384(one for 128) (three for 384) 1 23 45ONPOWER U Power Connection
Page 4-20NDA-24230 Issue 2.0 Chapter 4 VisuaLink 128/384 User Guide 21. Locate the network cable (RJ45-RJ45) and connect one end to the S/T LINE port of the VisuaLink 128 or VisuaLink 384. Connect the other end of the network cable into the S/T interface of the NT1. Note: RJ45-RJ45 cable that is included with the NT1 unit should be used. 22. Connect the network cable from the U interface on the NT1 to the network jack provided on the room wall. Proceed to Step 24. Note 1: RJ45-RJ45 cable that is included with the NT1 unit should be used. Note 2: If connecting a VisuaLink 384 system, Step 21 will have to be repeated three (3) times. STEP ACTION DRAWING + + ++ +DC IN 5V+ - Serial1 Serial2/RMT O U T I N VIDEO2 VIDEO1 AUDIO ++TEL S/T LINEMIC1 MIC2 MIC3 RJ45 NT1 Cable S/T S/TL-BK LINE PWR DIN INTERFACE ST InterfacesVisuaLink 128 Rear NT1 Front + + ++ +DC IN 5V+ - Serial1 Serial2/RMT O U T I N VIDE O2 VIDEO1 AU DIO ++TEL S/T LIN E 1 S/T LINE 2 S/T LINE 3MIC1 MI C2 MIC3 VisuaLink 384 Rear RJ45 NT1 Cable 1234 5ONPOWER U NT1 Rear U Interface
NDA-24230 Issue 2.0Page 4-21 VisuaLink 128/384 User Guide Chapter 4 23. Locate the network cable (RJ45-RJ45) and connect one end to the S/T LINE port of the VisuaLink 128 or VisuaLink 384. Connect the other end of the network cable into the network interface provided in the room wall. Note 1: If the NT1 or network switch resides 300 feet (91 meters) or more away from the VisuaLink 128 or VisuaLink 384, it is recommended that the TERM switch is set to ON on the VL128. Note 2: In the case a VL384 is being installed, the network interface card must be taken out of the system and the appropriate strap must be set. Note 3: If the VL 384 is being installed, Step 23 must be repeated three (3) times. 24. Locate the ON/OFF switch at the upper right outside of the cabinet. Press the switch to the ON position. STEP ACTION DRAWING + + ++ +DC I N 5 V+ - Serial1 Serial2/RMT O U T I N VIDEO2 VIDEO1 AUDIO ++TEL S/T LINEMIC1 MIC2 MI C3 RJ45 NT1 Cable + + ++ +DC IN 5V+ - Serial1 Serial2/RMT O U T I N VIDE O2 VIDEO1 AU DIO ++TE L S/T LINE 1 S/T LIN E 2 S/T LIN E 3MIC1 MI C2 MIC3 VisuaLink 384 Rear RJ45 NT1 Cable VisuaLink 128 Rear ON/OFF Switch
Page 4-22NDA-24230 Issue 2.0 Chapter 4 VisuaLink 128/384 User Guide 25. Verify that all the equipment plugged into the power strip are turned to the ON position. The VisuaLink 128, VisuaLink 384, camera and monitor have their own power switches. If a device appears to be still in the OFF position, check the power connection from the Power Strip to the device. The NT1 does not have a power switch. The green LED on the front of the NT1 is an indication the unit is powered ON . Note: Make sure the monitor is selected for Video 1. 26. When the VisuaLink 128 or VisuaLink 384 is powered ON , a display of the NEC America, Inc logo, VisuaLink name, POWERING UP and version number will be displayed on the monitor. STEP ACTION DRAWING POWER HEADS ET POWERLI NEB1 B2 Powering Up Ver.22.02.37 Vi s u a L i n k America, Inc.