NEC Sentry Installation Guide

NDA-30080   Revision 1.0Page 41
Sentry Installation Guide Annoyance Trap
Primary 
Configuration 
ParametersThese parameters are defined automatically if you answered “yes” to the 
autoconfig prompt during installation. On the APM Configuration Entry screen, 
make the entries indicated below for each Annoyance Trap parameter. Entries for 
parameters marked by an asterisk (*) must be made exactly as shown. Other entries 
are examples and are site-dependent. 
Note:
Use the instructions provided for this...

Page 42NDA-30080   Revision 1.0
Annoyance Trap Sentry Installation Guide
OAI FacilitiesThese NEAX 2400 facilities are set up automatically if you answered “yes” to the 
autoconfig prompt during installation. To manually set up the facilities, use the 
Facilities command on the APM Configuration Entry screen and follow the 
instructions in the APM Operations Manual.
ParameterEntryDescription
FacilitiesSCF SMFR SMFN The OAI facilities required by 
Annoyance Trap. 

NDA-30080   Revision 1.0Page 43
Sentry Installation Guide Annoyance Trap
Secondary OAI 
Configuration 
ParametersThese parameters are defined automatically if you answered “yes” to the 
autoconfig prompt during installation. Use the OAI-Conf command on the APM 
Configuration Entry screen to make the entries indicated below for each parameter. 
Entries for parameters marked by an asterisk (*) must be made exactly as shown. 
Other entries are examples and are site-dependent. 
Note:
Use the instructions...

Page 44NDA-30080   Revision 1.0
Annoyance Trap Sentry Installation Guide
User-Defined 
Parameters
Note:The following parameters contain configuration pairs consisting of a keyword, at least one blank space, and an option. Multiple configuration 
pairs may be specified in a single parameter if space permits. Case is ignored for keywords, but options must match exactly. The configuration pairs may 
occur in any order, and the following keywords and options are supported
ParameterEntryDescription
User...

NDA-30080   Revision 1.0Page 45
Sentry Installation Guide Annoyance Trap
Database Requirements
Annoyance Trap requires two databases: the Building database and the Tenant 
database. 
This section contains needed to create Emergency Conference databases. Use this 
information with the procedural instructions in the APM Operations Manual. If 
you encounter messages during this process, refer to the “Process” and “Error 
Messages” chapters of the APM Operations Manual.
Database CreationThe following steps...

Page 46NDA-30080   Revision 1.0
Annoyance Trap Sentry Installation Guide
Building DatabaseThe Building database is shared with other Sentry applications, so you might not 
have to build it for Annoyance Trap. You will receive a message from the APM if 
you try to create the Building database and it already exists.
The Building database contains a list of extensions and the location of each 
extension. A building location can be associated with an individual numeric 
extension or a range of numeric...

NDA-30080   Revision 1.0Page 47
Sentry Installation Guide Annoyance Trap
Tenant Number 
DatabaseThe Tenant Number database is shared with other Sentry applications, so you 
might not have to build it for Annoyance Trap. You will receive a message from 
the APM if you try to build the Tenant database and it already exists.
The Tenant Number database contains a list of extensions and associated tenant 
numbers used by the PBX. A tenant number can be associated with an individual 
numeric extension or a...

Annoyance Trap Sentry Installation Guide
Page 48NDA-30080   Revision 1.0
This Page Left Blank. 

NDA-30080   Revision 1.0Page 49
Sentry Installation Guide Emergency Conference
Chapter 4 Emergency Conference
This chapter describes the field entries to make during the installation and 
configuration of the Emergency Conference software. For information on using 
Emergency Conference, see the Emergency Conference User Guide.
Overview
The Emergency Conference program is an OAI application that allows a user to 
call a designated emergency conference number and to connect to a set of 
predefined...

Page 50NDA-30080   Revision 1.0
Emergency Conference Sentry Installation Guide
Additional Manuals
In addition to this guide, use instructions in the following manuals for this 
installation:
Applications Manager (APM) Installation Manual - Contains step-by-step 
instructions for installing the software from the release media.
Applications Manager (APM) Operations Manual - Explains how applications like 
Emergency Conference are configured in the APM environment and how the 
Emergency Conference databases...