NEC Projector PH1202HL User Manual

126
[SOURCE(2)]
SIGNAL	TYPE	VIDEO	TYPE	
BIT	DEPTH	 VIDEO	LEVEL	
LINK	RATE	LINK	LANE
3D	FORMAT
[SOURCE(3)]
INPUT	TERMINAL	RESOLUTION	
HORIZONTAL	FREQUENCY	VERTICAL	FREQUENCY	
SYNC	TYPE	 SYNC	POLARITY	
SCAN	TYPE	SOURCE	NAME	
ENTRY	NO.
[SOURCE(4)]
SIGNAL	TYPE	VIDEO	TYPE	
BIT	DEPTH	 VIDEO	LEVEL	
LINK	RATE	LINK	LANE
3D	FORMAT
5. Using On-Screen Menu  

127
[WIRED LAN]
IP	ADDRESS	SUBNET	MASK	
GATEWAY	 MAC	ADDRESS
[VERSION(1)]
FIRMWARE	DATA	
SUB-CPU
[VERSION(2)]
FIRMWARE3
5. Using On-Screen Menu  

128
[OTHERS]
DATE	TIME	PROJECT OR	NAME	
MODEL	NO.	SERIAL	NUMBER	
CONTROL	ID	(when	[CONTROL	ID]	is	set)
[CONDITIONS]
INTAKE	TEMPERATURE	 EXHA UST	TEMPERATURE	
ATMOSPHERIC	PRESSURE
[HDBaseT]
SIGNAL	QUALITY	OPERATION	MODE	
LINK	STATUS	 HDMI	ST ATUS
5. Using On-Screen Menu  

129
❶ Connecting a computer
A	computer	cable,	BNC	cable	(5-core	type),	HDMI	cable ,	or	a	DisplayP ort	cable	can	be	used	to	connect	to	a	computer.
The	connection	cable	is	not	enclosed	with	the	projector.	Please	get	ready	a	suitab le	cab le	f or	the	connection.
Analog RGB signal connection
•	 Connect	the	computer	cable	to	the	display	output	terminal	(mini	D-sub	15	pin)	on	the	computer	and	the	COMPUTER	
IN	terminal	on	the	projector.	Please	use	a	computer	cable	attached	with	a	f errite	core .
•	 When...

130
Digital RGB signal connection
•	 Connect	a	commercially	available	HDMI	cable	between	the	computer’s	HDMI	output	terminal	and	the	projector’s	
HDMI	IN	terminal.
•	 Connect	a	commercially	available	DisplayP ort	cable	between	the	computer’s	DisplayP ort	output	terminal	and	the	
projector’s	DisplayPort	IN	terminal.
•	 Select	the	source	name	for	its	appropriate	input	terminal	after	turning	on	the	projector.
Input	terminalSOURCE	button	on	the	projector	
cabinetButton	on	the	remote	control
HDMI	IN	HDMIHDMI...

131
Cautions	when	connecting	an	HDMI	cable
•	 Use	a	certified	High	Speed	HDMI®	Cable	or	High	Speed	HDMI®	Cable	with	Ethernet.
Cautions	when	connecting	a	DisplayPort	cable
•	 Use	a	certified	DisplayPort	cable.
 
•	 Depending	on	the	computer,	some	time	may	be	required	until	the	image	is	displayed.
•	 Some	DisplayPort	cables	(commercially	available)	have	locks.
•	 To	disconnect	the	cable,	press	the	button	on	the	top	of	the	cable’s	terminal,	then	pull	the	cable	out.
•	 Power	can	be	supplied	to	the	connecting...

132
Cautions	when	using	a	DVI	signal
•	 When	the	computer	has	a	DVI	output	terminal,	use	a	commercially	available	conv erter	cable	to	connect	the	com-
puter	to	the	projector’s	HDMI	IN	terminal	(only	digital	video	signals	can	be	input).	
HDMI IN
NOTE:	When	Viewing	a	DVI	Digital	Signal
•	 Turn	off	the	power	of	the	computer	and	projector	before	connecting	devices.
•	 When	a	video	deck	is	connected	via	a	scan	converter,	etc.,	the	display	may	not	be	correct	during	fast-forwarding	and	rewinding.
•	 Use	a...

133
HDMI IN
HDMI OUTHDMI IN
❷ Connecting an External Monitor
As	shown	in	the	figure,	when	the	projector	is	connected	to	a	computer,	the	same	content	from	the	HDMI	input	signal	
is	displayed	on	the	monitor	for	confirmation.
•	 The	HDMI	OUT	terminal	cannot	send	analog	signals	(COMPUTER	IN	terminal,	BNC	terminal).
•	 Please	refer	to	Page	58	when	displaying	the	PIP/PBP	screen.
NOTE:
•	 When	outputting	HDMI	signals,	turn	on	the	power	of	the	video	device	on	the	output	side	and	keep	it	connected	before...

134
❸ Connecting Your Blu-ray Player or Other AV Equipment
Component	video	signal/S-video	signal	connection
•	 Select	the	source	name	for	its	appropriate	input	terminal	after	turning	on	the	projector.
Input	terminalSOURCE	button	on	the	projector	
cabinetButton	on	the	remote	control
BNC(CV)	BNC(CV)VIDEO
BNC(Y/C)
	BNC(Y/C)S-VIDEO
CV YC
BNC¢CV£
BNC
¢Y£
BNC¢C£
If	the	signal	is	a	composite	video	signalBNC	cable	(not	supplied)If	the	signal	is	an	S-video	signalBNC	cable	(not	supplied)
Audio	equipment
6....

135
Connecting Component Input
Connect	the	Blu-ray	player’s	audio	to	the	audio	device.
•	 Select	the	source	name	for	its	appropriate	input	terminal	after	turning	on	the	projector.
Input	terminalSOURCE	button	on	the	projector	
cabinetButton	on	the	remote	control
COMPUTER	IN	COMPUTERCOMPUTER	1
BNC	BNCCOMPUTER	2
NOTE:
•	 When	the	signal	format	is	set	to	[AUTO]	(default	factory	setting	when	shipped),	the	computer	signal	and	component	signal	are	
automatically	distinguished	and	switched.	If	the	signals	cannot...