NEC Neax2000 Ivs Circuit Card Manual

ND-45504 (E) CHAPTER 2
Addendum-002 Page 3
OCTOBER, 1998 Revision 2.2
CHAPTER 2 FUNCTIONAL OUTLINE OF CIRCUIT CARDS
This chapter explains the functional outline of various circuit cards used in the NEAX2000 IVS. Explanations are
given in alphabetical order of the circuit card names for each kind (Control, Application, and Line/Trunk) of circuit
cards.
1. CONTROL CIRCUIT CARDS
Table 2-1 shows the functional outline of each control circuit card.
Table 2-1  Functional Outline of Control Circuit Cards
CARD...

CHAPTER 2  ND -4 5504 ( E)
2. APP LIC ATIO N CIRCUI T CARDS 

ND-45504 (E) CHAPTER 2
Addendum-001 Page 5
JULY, 1998 Revision 2.1
PN-CC01 ETHEREthernet Control card.
This card is used with the PN-AP01 card to accommodate the Ethernet, transmit-
ting/receiving a signal of TCP/IP protocol.
10 BASE-T twisted pair cable can be connected directly to this card.
PN-CK00 PLOPhase Locked Oscillator card.
This card is a phase locked oscillator for providing a synchronized clock signal 
with the network.
This card is used when the PBX is a master office or when the PBX...

CHAPTER 2 ND-45504 (E)
Pag e 6
Revision 2.0
3. LINE/TRUNK CIRCUIT CARDS
Table 2-3 shows the functional outline of each line/trunk circuit card.
Table 2-3  Functional Outline of Line/Trunk Circuit Cards
CARD NAMEFUNCTIONAL 
NAMEFUNCTIONAL OUTLINE
PN-2AMPA AMP2-line Amplifier Trunk card.
This card is equipped with the functions of Echo Canceller (EC), Automatic Gain 
Controller (AGC) and Tone Disabler (TD).
PN-AUCA AUC2-line Long-Line circuit card provided with the Power Failure Transfer (PFT) 
function....

ND-45504 (E) CHAPTER 2
Page 7
Revision 2.0
PN-4DLCA DLC4-line Digital Line Circuit card for D
term Series E/Series III/ElectraPro/DSS Con-
sole.
[–27 V Version, 2-wire type, line length: max. 200 m (656 ft.)]
This card is equipped with quick diagnostics to detect short line conditions and 
the normality (Synchronous/Asynchronous) of the terminal.
PN-4DLCD DLC4-line Digital Line Circuit card exclusively used for D
term Series E/Series III.
[-27 V Version, 2-wire type, line length: max. 200 m (656 ft.)]...

CHAPTER 2 ND-45504 (E)
Pag e 8
Revision 2.0
PN-4LCJ LC4-line Analog Line Circuit card for single line telephones.
This card provides 4 circuits with Disconnect Supervision.
Loop resistance: Max. 600 ohms.
This card is equipped with quick diagnostics to detect short and open line condi-
tions.
PN-M03 M03V.35 DTE interface card.
This card is used together with the PN-2DPCB card to provide the V.35 interface.
PN-2ODTA ODT2-line OD Trunk card.
This card can be used as either a 2-wire E&M trunk or a 4-wire...

ND-45504 (E) CHAPTER 3
Addendum-002 Page 9
OCTOBER, 1998 Revision 2.2
CHAPTER 3 CIRCUIT CARD INSTALLATION CONDITIONS
This chapter explains the conditions for installing various kinds of circuit cards used in the PBX.
1. CIRCUIT CARD MOUNTING SLOTS
Figure 3-1 below shows circuit card mounting slots allocated in the PIM based on circuit card type.
Figure 3-1   Circuit Card Mounting Slots
FP/AP6 MP/FP/AP7
LT05
LT04
LT03
LT02
LT01 LT06 LT07
LT00 - LT15  : Line/trunk circuit card mounting slots
AP0 - AP8 :...

CHAPTER 3 ND-45504 (E)
Page 10 Addendum-002
Revision 2.2 OCTOBER, 1998
Figure 3-1   Circuit Card Mounting Slots (Continued)
LT00 - LT15  : Line/trunk circuit card mounting slots
AP0 - AP8 : Application circuit card mounting slots
MP0, MP1 : PN-CP02/PN-CP02-C mounting slot
FP : PN-CP01 mounting slots
BUS : PN-BS00-A/PN-BS00-B, PN-BS01-A/PN-BS01-B mounting slot
PWR : PZ-PW86/PZ-PW86-A/PZ-PW86 (C)/(D) mounting slot
*1Either line/trunk circuit cards or application circuit cards can be mounted in these...

ND-45504 (E) CHAPTER 3
Addendum-002 Page 11
OCTOBER, 1998 Revision 2.2
2. INSTALLATION CONDITIONS FOR CONTROL CIRCUIT CARDS
2.1 PN-CP00/PN-CP00-B/PN-CP00-C (MP)
Mount the PN-CP00/PN-CP00-B/PN-CP00-C in the MP slot of PIM0.
2.2 PN-CP01 (FP)
1. The PN-CP01 is required only if any of the following is true.
• More than one PIM is used.
• A PN-2DLCC is used.
• A PN-AP01 is used.
• OAI, ACD, No. 7 CCIS or ISDN is used.
2. When the system is equipped with two PIMs, mount one PN-CP01 in the FP slot of PIM0. When...

CHAPTER 3 ND-45504 (E)
Page 12 Addendum-002
Revision 2.2 OCTOBER, 1998
2.3 PN-CP02/PN-CP02-C (MP)
Mount the PN-CP02/PN-CP02-C in the MP0 and MP1 slot of PIM(H)0.
This card is used only for Back up MP system.
Figure 3-3   MP/FP Card Mounting Slots for Back up MP System
PIM3PIM7
PIM2PIM6F
PF
P
PIM1PIM5
PIM(H)0PIM4F
PM
PF
PP M
0 1