NEC Neax 2400 Ipx System Operations And Maintenance Manual
Here you can view all the pages of manual NEC Neax 2400 Ipx System Operations And Maintenance Manual. The NEC manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 81
NDA-24307 CHAPTER 3 Page 53 Issue 1 SYSTEM MESSAGES 6-M Emergency Control Stop 129 6-N Abnormal Call Duration Data 130 6-O SMDR Output Buffer Overflow Alarm 133 6-P SMDR Output Buffer Overflow Release 136 7-A System Initialize With Data Load 137 7-B System Initialize 139 7-C CPU MBR Key Turn ON 140 7-D CPU MBR Key Turn OFF 141 7-E TSW MBR Key Turn ON 142 7-F TSW MBR Key Turn OFF 143 7-I ALMC MB Key Turn ON 144 7-J ALMC MB Key Turn OFF 145 7-K PM MB Key Turn ON 146 7-L PM MB Key Turn OFF 147 7-M NCU MB...
Page 82
CHAPTER 3 NDA-24307 Pag e 5 4 Issue 1 SYSTEM MESSAGES 13-P Digital Line Restore 198 13-Q DAU Battery Operation 199 13-R DAU Line Operation 200 13-Z Power Failure 201 15-A VPS Failure (Temporary) 202 15-B VPS Failure (Permanent) 203 15-C VPS Restore 204 16-A Inside Trunk All Busy 205 16-B Virtual Tie Line Set Report 207 16-C Virtual Tie Line Cancel Report 208 16-E Virtual Tie Line Set Time Out 209 16-F Sender Start Time Out 212 16-K I/O Port Line OFF 219 16-L I/O Port Line Restore 220 16-M Hard Clock...
Page 83
NDA-24307 CHAPTER 3 Page 55 Issue 1 SYSTEM MESSAGES Note 1: Refer to “Fusion Network System Manual.” Note 2:Refer to the manual related to ATM. Note 3:Refer to “Wireless System Manual.” Note 4:Refer to the manual related to OAI. 23-P Dch Back-Up Automatic Change Start/End 240 23-Q Dch Back-Up Manual Change Start/End242 23-R ATM Interface Change Report Note 2- 23-S FCCH Failure Note 1- 23-T FCCH Failure Recovered Note 1- 23-U FCCH Status Notice Note 1- 23-W FCCH Advancing Start Note 1- 23-X FCCH Advancing...
Page 84
CHAPTER 3 NDA-24307 Pag e 5 6 Issue 1 SYSTEM MESSAGES This message displays when the processor is reset due to a failure in the system. ➀ Self-CPU Restart Information ➁ Mate-CPU Restart Information (FF H: not mounted) ➂ Related-call Release Result See Chapter 5 for repair procedure. 1: XXXX XX00 XXXX 0000 2: 0000 0000 0000 0000 3: 0000 0000 0000 0000 ➀ ➁ ➂ ➃ 4: 0000 0000 0000 0000 5: 0000 0000 0000 0000 6: 0000 0000 0000 0000 7: 0000 0000 0000 0000 8: 0000 0000 0000 0000 9: 0000 0000 0000 0000 b7 b6 b4...
Page 85
NDA-24307 CHAPTER 3 Page 57 Issue 1 SYSTEM MESSAGES ➃Data Load Result after restart processing Note 1:Phase 1 Restart is executed when initializing the system without disrupting the following two-way connections that have already been established: Basic two-way connections (STN-STN, STN-TRK, TRK-TRK) Fixed connections Two-way connections established on a Fusion link For more details, see Chapter 6, Section 12. Note 2:The number sharing data load also affects the data load of Dual Station Calling...
Page 86
CHAPTER 3 NDA-24307 Pag e 5 8 Issue 1 SYSTEM MESSAGES This message displays when a fault has occurred to the clock oscillator in the CPU. ➀ Self-CPU Restart Information ➁ Mate-CPU Restart Information (FF H: not mounted) ➂ Related Call Information See Chapter 5 for repair procedure. 1: XXXX XX00 0000 0000 2: 0000 0000 0000 0000 3: 0000 0000 0000 0000 ➀ ➁ ➂ 4: 0000 0000 0000 0000 5: 0000 0000 0000 0000 6: 0000 0000 0000 0000 7: 0000 0000 0000 0000 8: 0000 0000 0000 0000 9: 0000 0000 0000 0000 b7 b5 b4 b3...
Page 87
NDA-24307 CHAPTER 3 Page 59 Issue 1 SYSTEM MESSAGES C-level infinite loop is a state where a clock-level program, running under clock interrupt disable state, is in an infinite loop. This message displays when the counter value to check the normality of the processing has become abnormal. ➀ Self-CPU Restart Information after clock fault occurrence ➁ Mate-CPU Restart Information ➂ NMI Factor See Chapter 5 for repair procedure. 0-E C-level Infinite Loop 1: XXXX XXXX XXXX XXXX 2: XXXX XXXX XXXX XXXX 3:...
Page 88
CHAPTER 3 NDA-24307 Pag e 6 0 Issue 1 SYSTEM MESSAGES ➃ System Controlling Port B ➄ CPU Alarm ➅ CPU Changeover Factors ➆ System ALM ➇ Data to be Analyzed by NEC Engineers b7 b6 b5 b4 b3 b2 b1 b0 b7 b6 b5 b4 b3 b2 b1 b0 b7 b6 b5 b4 b3 b2 b1 b0 b7 b6 b5 b4 b3 b2 b1 b0 b7 b6 b5 b4 b3 b2 b1 b0 b0: 0/1 = Timer 2 Gate ON/OFF b1: 0/1 = Speaker Gate ON/OFF b2: 0/1 = Parity Check Enable/MASK b3: 0/1 = Channel Check Enable/MASK b4: 0/1 = -/RAM Refresh Pulse Output State b5: 0/1 = -/Timer 2 Output State b6: 0/1 =...
Page 89
NDA-24307 CHAPTER 3 Page 61 Issue 1 SYSTEM MESSAGES This message displays when a CPU memory read/write error occurs. ➀Information on Self-CPU Restart after detection of a clock fault ➁ Mate-CPU Restart Information ➂ NMI Factor See Chapter 5 for repair procedure. 0-F Memory Failure 1: XXXX XXXX XXXX XXXX 2: XXXX XXXX XXXX XXXX 3: XXXX XXXX XXXX XXXX ➀ ➁ ➂ ➃ ➄ ➅ ➆ ➇ 4: XXXX XXXX XXXX XXXX 5: XXXX XXXX XXXX XXXX 6: XXXX XXXX XXXX XXXX ➇ 7: XXXX XXXX XXXX XXXX 8: XX00 0000 0000 0000 9: 0000 0000 0000...
Page 90
CHAPTER 3 NDA-24307 Pag e 6 2 Issue 1 SYSTEM MESSAGES ➃ System Controlling Port B ➄ CPU Alarm ➅ CPU Changeover Factors ➆ System ALM ➇ Data to be Analyzed by NEC Engineers b7 b6 b5 b4 b3 b2 b1 b0 b7 b6 b5 b4 b3 b2 b1 b0 b7 b6 b5 b4 b3 b2 b1 b0 b7 b6 b5 b4 b3 b2 b1 b0 b7 b6 b5 b4 b3 b2 b1 b0 b0: 0/1 = Timer 2 Gate ON/OFF b1: 0/1 = Speaker Gate ON/OFF b2: 0/1 = Parity Check Enable/MASK b3: 0/1 = Channel Check Enable/MASK b4: 0/1 = -/RAM Refresh Pulse Output State b5: 0/1 = -/Timer 2 Output State b6: 0/1 =...