NEC Neax 2400 Ipx Installation Manual

NDA-24306 CHAPTER 7
Page 373
Revision 1.0
CHAPTER 7 WORK AFTER INSTALLATION TESTS
This chapter explains various kinds of work and site cleaning, etc. which the installer must perform after com-
pletion of installation tests so that the system can be cut over normally.
Upon completion of all the required tests, the technician must confirm or perform the following.
1. Office Data Management
2. Preparation of Test Result Reports
3. Mounting of the Front and Rear Covers
4. Attachment of Inter-frame Brackets...

CHAPTER 7 NDA-24306
Page 374
Revision 1.0
WORK AFTER INSTALLATION TESTS
Note:
Cautions pertaining to Floppy Disks.
(1) Do not place a heavy object on an FD or the FD will be damaged.
(2) When taking an FD out of its protective envelope, hold the top edge of the disk and gently pull it out.
(3) Do not expose the FD to direct sunlight or to a high temperature (above 65°C (150°F)).
(4) Do not pinch the FD with a clip.
(5) Do not touch the recorded surface of the floppy disk with bare hands; fingerprints...

NDA-24306 CHAPTER 7Page 375
Revision 1.0
WORK AFTER INSTALLATION TESTS
3. MOUNTING OF THE FRONT AND REAR COVERS
When mounting the front cover and the rear cover of the PBX, follow the procedure below.
START Inspection Set all MB switches back to their positions  prior to the installation tests.
Confirm that all circuit cards are mounted in 
the proper slots according to the Bayface 
Layout.
M oun ting  of  Si de Cov ers   Referrin g  to  Figu res  7 -1  t h rough  7 -4 , m ount  
the side covers onto the...

CHAPTER 7 NDA-24306
Page 376
Revision 1.0
WORK AFTER INSTALLATION TESTSFigure 7-1   Mounting of the Covers in a Full System
FRONT  
COVER FRONT
SIDE COVERS
REAR COVERS
SIDE COVERS 

NDA-24306 CHAPTER 7
Page 377
Revision 1.0
WORK AFTER INSTALLATION TESTS
Figure 7-2   Mounting of the Covers 

CHAPTER 7 NDA-24306
Page 378
Revision 1.0
WORK AFTER INSTALLATION TESTS
Figure 7-3   Side Cover Mounting Method (BASEU+LPM+PIM0)
SCREWFRONT
REAR
SIDE COVER 

NDA-24306 CHAPTER 7
Page 379
Revision 1.0
WORK AFTER INSTALLATION TESTS
Figure 7-4   Side Cover Mounting Method (PIM)
Note: The cover can also be mounted upside-down, so confirm the upper and lower sides.
 The side covers included with the Top Unit (TOPU) are different from the module covers shown here. 

CHAPTER 7 NDA-24306
Page 380
Revision 1.0
WORK AFTER INSTALLATION TESTS
Figure 7-5   Rear Cover Mounting Method (BASEU+LPM+PIM0)
SCREW
SCREW
SCREW SCREW
SCREW
SCREW REAR SIDE
REAR COVER
SIDE VIEW
REAR COVER 

NDA-24306 CHAPTER 7
Page 381
Revision 1.0
WORK AFTER INSTALLATION TESTS
Figure 7-6   Rear Cover Mounting Method (PIM)
MODULE
REAR SIDE
REAR COVER SCREWSCREW
MODULE
REAR COVER
SIDE VIEW 

CHAPTER 7 NDA-24306
Page 382
Revision 1.0
WORK AFTER INSTALLATION TESTS
Figure 7-7   Rear Cover Mounting Method (FANU)
FA N U
REAR COVER
SCREW
SCREW
FA N U
REAR COVER