NEC Neax 2400 Ipx Hotel Office Data Specification

							NDA-24315 COMMAND LIST
Page v
Issue 1
HOTEL COMMAND LIST IN ALPHANUMERIC ORDER
COMMAND 
NAMEFULL COMMAND NAMEPA G E
AACLAssignment of Administration Station Class244
AANPAssignment of Administration Numbering Plan91
AASNAssignment of Alternated Administration Station Number243
AASPAssignment of Administration Special Access Code101
AASTAssignment of Administration Station Data237
ADNRAssignment of Day/Night Restriction235
ADSSAssignment of Direct Station Select253
AGCLAssignment of Guest Station Class247
AGNPAssignment of Guest Numbering Plan94
AGN PLAssignment of Guest Numbering Plan for LDM96
AGNPNAssignment of Guest Numbering Plan for NDM99
AGSNAssignment of Alternated Guest Station Number246
AGSPAssignment of Guest Special Access Code129
AGS PLAssignment of Guest Special Access Code for LDM155
AGSPNAssignment of Guest Special Access Code for NDM180
AGS TAssignment of Guest Station Data240
AHSUAssignment of Suite Room Station Number249
AHSYAssignment of Hotel System Parameter52
ASCRAssignment of Station Connection Restriction231
ASPFAssignment of Special Access Code Floor255
ASPSAssignment of Special Access Code for Split Access205
AT C RAssignment of Telephone Class Restriction233 
						

							COMMAND LIST NDA-24315
Pag e vi
Issue 1
This page is for your notes. 
						

							NDA-24315 CHAPTER 1
Page 1
Issue 1
CHAPTER 1 INTRODUCTION
1. General
This manual describes how to operate the Maintenance Administration Terminal (MAT) and plan the office
data. It also contains descriptions of the parameters for the NEAX2400 IPX.
2. How to Follow This Manual
The contents of this manual are:
• CHAPTER 1 INTRODUCTION
This chapter explains how to use this manual.
CHAPTER 2 ASSIGNMENT
This chapter explains the system configuration and system specifications required to install and run the
MAT. It contains installation instructions and information about accelerator keys and navigation keys used
by MAT.
CHAPTER 3 OFFICE DATA DESIGN SHEET
This chapter contains the office design sheets used to design the configuration and specification of IPX.
CHAPTER 4 HOTEL SYSTEM COMMAND DESCRIPTIONS AND DATA SHEETS
This chapter explains the Hotel system command parameters of the NEAX2400 IPX.
3. Reference Manuals
When installing MAT and assigning the relevant system data, refer to the following manuals in addition to this
manual:
 Feature Programming Manual
 Fusion Network System Manual
 Office Data Specification (for Business system commands)
Note:The NEAX2400 IPX Office Data Specification for Business systems contains Hotel system-related
command information in the following sections:
• AAEDAKYDASPA
 AAKPALRNNASPAL
 AASPANPNASPAN
 AAST ARTDASYD
AGST ARTDNATIM
AIOCASFCATIMN 
						

							CHAPTER 1 NDA-24315
Page 2
Issue 1
This page is for your notes. 
						

							NDA-24315 CHAPTER 2
Page 3
Issue 1
ASSIGNMENT
CHAPTER 2 ASSIGNMENT
1. General
This chapter describes the information needed to install and operate the Maintenance Administration Terminal
(MAT) software.
The IPX MAT software has the following functions:
 Allows user-friendly Graphical User Interface (GUI) with Microsoft Windows 95/NT.
 Provides both an Ethernet interface and a RS232C interface.
 Allows access to a node within the Fusion Link network using a simple Login operation,
 Supports remote maintenance capabilities through a dialup connection.
 Dumps the PBX data into a data file using of the LIST UP command.
Note:The recorded log file is a simple text file that can be printed or edited using any Windows application that
supports text file editing.
Since the IPX MAT runs on Microsoft’s 32 bit Windows plug-and-play operating system, peripheral hardware
(network, remote access, modems, printers, etc.) is easy to configure. IPX MAT does not require a dedicated
printer. Any printer supported by the operating system, including shared LAN printers, can be used.
2. Getting Started-Hardware
The IPX MAT PC should conform to the specifications explained in this section. The cables, modems, and
HUBs required depend on the connection type.
The IPX MAT allows you to access IPX using the following connection types:
 Serial/direct
 Serial/dialup
TCP/IP
2.1 PC Specifications
The IPX MAT software requires a PC with the following minimum specifications:
Table 2-1 PC Requirements to Run IPX MAT
CPU TYPEPentium 166 or higher
Memory32 MB or more for WIN 95 and NT
Hard Disk500 MB of free space
Video Card and MonitorAny Microsoft Windows compatible video card
(256 colors or more, screen size 800 X 600 resolution
ModemAny OS supported device; Required when IPX MAT is used for remote dialup access 
						

							CHAPTER 2 NDA-24315
Page 4
Issue 1
ASSIGNMENT
2.2 IPX MAT and IPX Connection
Figure 2-1 shows a serial/direct connection to the IOC card of IPX. The serial/direct connection allows you
to access the IPX and the different nodes via the Fusion Link.
Figure 2-1   Serial/Direct Connection to IPX
IPX MAT software supports serial/direct connection to the target IPX. As seen in Figure 2-2, a modem is
required at both the remote maintenance center and the IPX site. The LINE port of the modem located at
the IPX site should be connected to the dedicated Line Circuit (LC), and the DATA port should be directly
connected to the IOC card. The serial/dialup connection allows you to access both the first node (IPX) of
the Fusion Link network and all other nodes within the Fusion Link network.
CD-ROM DriveAny OS supported device
NetworkAny 10 BASE-T Network Interface Card when IPX MAT is connected across TCP/IP
Communication PortCOM1-COM4 when IPX MAT is connected across serial RS-232C port.
MouseAny Microsoft compatible mouse.
Operating SystemMicrosoft Windows 95 or Microsoft Windows NT
Be sure to set “small fonts” in the property of the screen. Table 2-1 PC Requirements to Run IPX MAT (Continued)
FUSION LINK
IPX
IPX NEAX 2400 TTY CABLE   1
IPX MATIPX MAT PRINTER
IOC
68PH S 2 PORTS CA - A
 
  
						

							NDA-24315 CHAPTER 2
Page 5
Issue 1
ASSIGNMENT
2.3 Serial/Dialup Connection to IPX
Figure 2-2   Serial/Dialup Connection to IPX
The IPX MAT software provides an advanced communication software for IPX. IPX is maintained via the
LAN, WAN, or TCP/IP network on which it is running. Figure 2-3 shows the simple configuration of the
TCP/IP connection. Using this connection, any node within the Fusion Link network can be accessed from
IPX MAT.
Figure 2-3   TCP/IP Connection to Dual CPR of IPX
FUSION LINK
IPX
IPX
IPX MATIPX MAT PRINTER
IOC
NEAX2400 TTY CABLE 368PH S 2 PORTS CA - A
LC
TRK
MODEM
MODEMTELECOMMUNICATION  
 
NETWORK
   
FUSION LINK 10 BASE -T  straight cable
HUB
IPX MAT
IPX MAT PRINTER
LANI
LANI
IPXIPX 
						

							CHAPTER 2 NDA-24315
Page 6
Issue 1
ASSIGNMENT
Figure 2-4 shows the configuration of the PBX and IPX MAT when connecting to an existing LAN. In most
cases you should use a network device such as a HUB or bridge to provide isolation from excessive network
traffic.
Figure 2-4   TCP/IP Connection (IP Address over the External LAN)
3. TCP/IP Considerations
The IPX MAT can communicate with the IPX via an Ethernet TCP/IP connection. In order for the IPX MAT to
communicate via TCP/IP, the PC must have its network software, including the TCP/IP drivers, installed and in
operation prior to installing the IPX MAT software.
SERVER PC
LAN MATHUB MAT PRINTER10BASE-T straight cable
PC
IPX
LANI
LANI 
						

							NDA-24315 CHAPTER 2
Page 7
Issue 1
ASSIGNMENT
If the PC does not have the network software installed and configured, a message indicating that the WINSOCK
2 setup has failed displays during the IPX MAT installation. This message is an expected response since the IPX
MAT installation program attempts to upgrade the TCP/IP WINSOCK drivers to the latest version. If these
drivers are not already installed, the upgrade process fails. The failure does not affect the successful installation
and operation of the IPX MAT, but the TCP/IP interface cannot be used.
It is always best to install the IPX MAT software after all network software is installed. Although it is not
recommended, it is possible to install the PC’s standard network software after the IPX MAT software has been
installed. If the IPX MAT software is installed prior to installing the network software, it will be necessary to
run the WINSOCK setup program from the IPX MAT CD after installing the network software.
To run the WINSOCK setup program:
1. Insert the IPX MAT CD into the CD-ROM drive.
2. The IPX MAT setup program starts automatically.
3. Terminate (Cancel) the IPX MAT setup program on the Welcome Screen.
Figure 2-5   IPX MAT Welcome Screen
4. Select the appropriate CD-ROM drive in Windows Explorer.
5. Double-click the file named WS2SETUP.EXE.
For more information about configuring TCP/IP connections, see Section 6.2, TCP/IP Connection.
4. Installing IPX MAT Software
The following provides step-by-step instructions for installing the IPX MAT software for Windows 95/NT onto
your hard disk.
1. Terminate all applications, prior to starting the installation process.
2. Insert the CD-ROM into the CD-ROM drive. (The IPX MAT installation program starts automatically.)
NEAX2400IPX
NEAX2400IPX 
						

							CHAPTER 2 NDA-24315
Page 8
Issue 1
ASSIGNMENT
3. Enter your name and your company name on the User Information dialog box. Then, click Next.
Figure 2-6   IPX MAT User Information Dialog
4. Click Next on the Choose Destination Location dialog box to install the IPX MAT software in the default
directory.
Note:If you wish to install the software in another directory, you can click Browse to display a dialog box that
allows you to select or create another directory.
Figure 2-7   Choose Location Destination Screen
IPXMAT