NEC Neax 2400 Ipx Hotel Office Data Specification

							NDA-24315 CHAPTER 4
Page 99
Issue 1
AGNPN: Assignment of Guest Numbering Plan for NDM
AG N P N: Assignment of Guest Numbering Plan for NDM
1. General
This command assigns the minimum number of digits needed to determine the service required by the first digit
received (pre-translation). The data assigned on this command is written in the Network Data Memory (NDM)
of the Network Control Node (NCN), updating the NDM at each Local Node (LN). 
2. Precautions
1. This command is used for the Hotel Application.
2. If the Guest and Admin. Numbering are separated (the ASYD command, SYS1, INDEX160, bit6 = 0),
use this command for the Guest Numbering plan. For the Admin. numbering plan, use the ANPDN com-
mand.
Note:Hotel features are available in TN1 only. If the AGNPN command is not common for all tenants, tenants
are restricted from calling between each other. Hotel Admin phones must be in tenant 1.
3. The system data assignment (ASYDN, SYS 1, INDEX 514, bit0 = 1) provides the Network Data Memory
(NDM).
3. Data Entry Instructions
TENANT
NUMBER
(TN)1st DIGIT CODE
(1st DC)CONNECTION 
STATUS INDEX
 (CI)
N/H/BNUMBER OF 
NECESSARY DIGITS
(NND)
MAXIMUM 6 DIGITSBUSY LAMP FIELD DISPLAY 
(BLF)
0/1
0
NND
The first digits analyzed, prior to the ASPAN command. To assign a
different number of digits for this, assign the minimum number of dig-
its to be used in this parameter.1st DC
The first digit of access code for Tele-
phone Number.
(0-9,*,#)
CI
The status of the “1st DC” dialed
N = Normal (Idle)
H = Hooking
B = BusyBLF
Not used (Fixed to 0) 
						

							CHAPTER 4 NDA-24315
Page 100
Issue 1
AGNPN: Assignment of Guest Numbering Plan for NDM
4. Data Sheet
TENANT
NUMBER
(TN)
1ST DIGIT
(1ST DC)
CONNECTION
STATUS 
INDEX
 (CI)
NUMBER OF 
NECESSARY DIGITS
(NND)
BUSY LAMP 
FIELD
(BLF)
REMARKS
1
NNormal
HHooking
BBusy
2
NNormal
HHooking
BBusy
3
NNormal
HHooking
BBusy
4
NNormal
HHooking
BBusy
5
NNormal
HHooking
BBusy
6
NNormal
HHooking
BBusy
7
NNormal
HHooking
BBusy
8
NNormal
HHooking
BBusy
9
NNormal
HHooking
BBusy
0
NNormal
HHooking
BBusy
NNormal
HHooking
BBusy
#
NNormal
HHooking
BBusy 
						

							NDA-24315 CHAPTER 4
Page 101
Issue 1
AASP: Assignment of Administration Special Access Code
AASP: Assignment of Administration Special Access Code
1. General
This command determines the kind of service to be executed or the route to be used when a Special Access code
or trunk Access code has been dialed for the Administration Station. 
2. Precautions
1. This command is used for the Hotel Application only.
2. If the Guest and Admin. Numbering are separated (the ASYD command, SYS1, INDEX 160, bit6 = 0),
use this command for the Admin. Special Access code. For the Guest Special Access code, use the AGSP
command.
Note:Hotel features are available in TN1 only. If the numbering plans are separated by tenants, the purpose for
each tenant is completely separated.
The Admin. Station required by the guest room call must be allocated in TN1.
3. If the numbering plan for Admin. and Guest is common (the ASYD command, SYS1, INDEX 160,
bit6=1), this command may be used to assign the Guest Special Access code as well.
4. The applicable Tenant Number (TN) range is designated by the ASYD command, SYS1, INDEX 8. Enter
the Tenant Number this command affects.
If data for this command is common for all tenants (ASYD command, SYS1, INDEX 92, bit1 = 1), assign
TN parameter as data “1” for all tenants.
5. The access code for C.F.-Busy Line and C.F.-Don’t answer service should be assigned by the ASYD
command, SYS1, INDEX 5, bit0 = 0 (Same) or 1 (Separate). 
6. The Access Code for Call Back and OG Trunk Queuing service should be assigned by the ASYD
command, SYS2, INDEX 4, bit0 = 0 (Separate) or 1 (Same).
7. To dial a different number of station number digits, the following programming is required.
Note:For the station number (ex. 200, 20000),
AANP1st.: 2 CI: N & H NND: 3
AASPACC: 200* CI: N & H SRV: SSC SID: 36 STATE: 63 (Dummy STA)
8. The following information states the rules of NND/NND1 data for Speed Calling-System and Call Park
Remote Retrieval.
Service FeatureSRVSIDNNDNND1
Speed Calling - SystemSSC15NND is the number of digits of the 
access code (ACC) NND1 is the number of digits 
abbreviated digits code (ADC)
Call Park Remote Retrieval 
CodeSSC63NND is the number of digits of the 
access code (ACC)– 
						

							CHAPTER 4 NDA-24315
Page 102
Issue 1
AASP: Assignment of Administration Special Access Code
9. For the following service features, the maximum number of digits is to be assigned in the parameter NND.
10. The variable parameter appears on the MAT depending on the data in the parameter SRV.
3. Data Entry Instructions 
SERVICE FEATURESRVSIDMAX. NND
Account Code DialSSC4115
Authorization Code/Forced Account CodeSSC4215
Attendant Manual OverrideSSC605
Access code (Max. 6 digits)
NND1 appears when SID = 15. The number of ADC
(Abbreviation Digit Code) digits should be assigned in NND1. TENANT
NUMBER
(TN)ACCESS CODE
(ACC)
MAX. 6 DIGITSCONNECTION 
STATUS INDEX
(CI) N/H/BKIND OF
SERVICE (SRV)
0-16
ACC
CISRV
NND1
SERVICE INDEX
(SID) 1-63NECESSARY DIGIT
(NND)NECESSARY DIGIT FOR SPEED
CALLING (NND1) 1-24 N = Normal service
H = Hooking service
B = Busy service
When SRV = SSC (Service code except SID36, 
56 and 57)  is assigned
15 (Speed Calling-System;
     Access)
41 (Account Code Dial)
15 (Authorization Code/Forced
      Account Code/Pad Lock)
60 (Attendant Manual Override)
63 (Call Park; Retrieve)NND appears when the following SID is entered.
NND data is variable depending on SID.NND
SIDNumber of digits for NND
Access Code (1-24)
Access Code (1-3) Access Code (1-5) Access Code+ID(1-15) Access Code+Account code
(1-15)
SSC = Service Code SSCA = Service code appendix
OGC = Outgoing call
OGCA = Outgoing call with route advance
LCR = Least cost routing LCRS = Register sender LCR
UNIF = Office termination
ANNC = Announcement service-single announcement
ANNCM = Announcement service-multiple announcement
PAGA = Paging Answer PAGC = Paging cancel 
						

							NDA-24315 CHAPTER 4
Page 103
Issue 1
AASP: Assignment of Administration Special Access Code
         STATE
(Hotel Service Code)
1 To be cleaned without ID code
2 Cleaning Completed without ID code
3 Ready for Occupancy without ID code
4 Use Not Allowed without ID code
 5-8 -
9 Maid Dial Answer Back without ID code-1
10 Maid Dial Answer Back without ID code-2
11 Maid Dial Answer Back without ID code-3
12 Maid Dial Answer Back without ID code-4
13 Maid Dial Answer Back without ID code-5
14 Maid Dial Answer Back without ID code-6
15 Maid Dial Answer Back without ID code-7
16 -
17 To be cleaned with ID code
18 Cleaning Completed with ID code
19 Ready for Occupancy with ID code
20 Use Not Allowed with ID code
21-24 -
25 Maid Dial Answer Back with ID code-1
26 Maid Dial Answer Back with ID code-2
27 Maid Dial Answer Back with ID code-3
28 Maid Dial Answer Back with ID code-4
29 Maid Dial Answer Back with ID code-5
30 Maid Dial Answer Back with ID code-6
31 Maid Dial Answer Back with ID code-7 
32 -
33 Automatic Wake Up Setting, Cancel; Same Special code
34 For Guest Station Secretary Telephone; Boss/Secretary Calling
35 Boss/Secretary Busy out; Set
36 Boss/Secretary Busy out; Cancel 
37  -
38 Automatic Wake-Up-Hotel Attendant Assistance Stop
39 Automatic Wake-Up-Hotel Attendant Assistance Stop Cancel
40 Alert Service Start (Hotel ATT)
41 Alert Service Stop (Hotel ATT)
42 Guest Service Telephone Screen Initialized
43 Guest Service Telephone Guest Room Information Retrieval
44 Direct Data Entry-Station (via Guest Station)
45 Alert Service Start (Special Admin. Station)
46 Alert Service Stop (Special Admin. Station)
47 -
48 2nd Wake-Up Call (Automatic) Set
49 2nd Wake-Up Call (Semi-Automatic) Set
50 2nd Wake-Up Call Cancel
51 Same Special Code Time Zone Connection Change
52 Same Special Code Time Zone Connection Change
53 Same Special Code Time Zone Connection Change
54 Same Special Code Time Zone Connection Change
55 Same Special Code Time Zone Connection Change
56-62 -
63 Dummy Number
Note: STATE=1-15 are used at the time of Maid ID Code Service is not provided;
           (ASYD SYS1 INDEX 164, bit3=0)
           STATE=17-31 are used at the time of Maid ID Code Service is provided;
           (ASYD SYS1 INDEX 164, bit3=1)
SERVICE INDEX
     (SID) 1-63
      STATE
36 
						

							CHAPTER 4 NDA-24315
Page 104
Issue 1
AASP: Assignment of Administration Special Access Code
SERVICE INDEX
    (SID) 1-63     NO.1
56
NO.1
(Kind of Assignment Number)
  Available numbers are 0-15.
  This data is used to assign Floor Service data by the ASPF
  command.
  Note: When programming Floor Service data, ASYD SYS1 
             INDEX 165, bit7=1 must have been assigned.
SERVICE INDEX
    (SID) 1-63NO.2KIND
57
NO.2
This parameter specifies the number (0-63) of the
access code being assigned for mutual access.
This parameter serves as a counter for the access
codes being assigned.
Note: This parameter is used when assigning the
           details of the service by the ASPS command.
KIND: (0-3)
This parameter specifies the Split Access Parameter Classification. The data to
be assigned here depends on how the Guest and Administration stations are
differentiated.
The Guest and Administration stations may be assigned to separate TNs, RSCs,
and/or SFCs, or they may only be differentiated by their respective designations
as Administration or Guest.
      0:    Administration/Guest
             (Assign this if the access code is to be shared between Guest
             and Administration with no correspondence to TN, RSC or SFC.)
      1:    TN
             (Assign this if the access code is to be shared among specified TNs)
      2:    RSC
             (Assign this if the access code is to be shared among specified RSCs)
      3:    SFC
             (Assign this if the access code is to be shared among specified SFCs) When SRV = SSC (Service code), SID56 (Floor Service) is assigned
When SRV = SSC (Service code), SID57 (Split Access) is assigned 
						

							NDA-24315 CHAPTER 4
Page 105
Issue 1
AASP: Assignment of Administration Special Access Code
NND
NND appears when SIDA = 97 (Call Hold Conference).
The number of digits for an access code should be assigned in NND.
SERVICE INDEX A (SIDA) 1-255PNO 1-15A/G
56
PNO
This parameter specifies the Admin./Guest
Numbering Parameter Classification.
After assigning the PNO, go to the AOSP
command to skip this ACC.
After skipping the access code, the system
refers to the numbering data designated in
the next parameter A/G.A/G
Numbering table designation for redevelopment
A: Admin.
G: Guest
When SRV = SSCA (Service code appendix) (except SIDA 56) is assigned
When SRV = SSCA (Service code appendix), SIDA 56 (Guest/Admin. Service) is assigned
SERVICE INDEX A (SIDA) 1-255 NECESSARY DIGIT (NND) 1-6 
						

							CHAPTER 4 NDA-24315
Page 106
Issue 1
AASP: Assignment of Administration Special Access Code
Assign the number of advanced trunk routes.ROUTE NUMBER
(RT)
COUNT
Assign a dummy route number.RT
2nd DTAuthorization code after dialing
ACC (LCR) + Destination number
0 = Out of Service
1 = In ServiceAH
ISDN-Sub Address Dialing
0 = Out of Service
1 = In ServiceSUB ROUTE NUMBER
(RT)SECOND DIAL TONE
(2nd DT) 0/1AUTHORIZATION CODE
(AH) 0/1SUB ADDRESS DIALING
(SUB) 0/1 INDEX COUNTER (COUNT)
INDEX ROUTE NUMBER (RT)
When SRV = OGC (Outgoing call) is assigned
When SRV = PAGA (Paging answer) is assigned
When SRV = PAGC (Paging cancel) is assigned
When SRV = OGCA (Outgoing call with route advance) is assigned
When SRV = LCR (Least cost routing) is assigned
When SRV = LCRS (Register sender LCR) is assigned
INDEX
INDEX is the route advance order.
1
2
3
Second dial tone sending (which is sent when a station has
dialed the digits specified in NND of the AANP command)
0 = Second DT is not send
1 = Second DT is sent 
						

							NDA-24315 CHAPTER 4
Page 107
Issue 1
AASP: Assignment of Administration Special Access Code
SKIP DIGITS
(SKIP) 0-5 When SRV = UNIF (Office termination) is assigned
When SRV = ANNC (Announcement service-Single announcement) is assigned
SKIP
ANNOUNCEMENT EQUIPMENT NUMBER
(EQP) 0-127
EQP
Note:    This data is available for ACIS only. For CCIS, use the AUNE command.Assign the skip digits to terminate the call.
Assign the announcement equipment number.
EQP3 and 5-14 can be used for SRV = ANNC (Single announcement).
Assign the tenant number of
the announcement trunk. When SRV = ANNCM (Announcement service-Multiple announcement) is assigned
TN TENANT NUMBER
(TN) 1-255 ANNOUNCEMENT EQUIPMENT NUMBER
(EQP) 122-125 Assign the announcement equipment number 
range from 122 to 125 (Multi announcement).EQP 
						

							CHAPTER 4 NDA-24315
Page 108
Issue 1
AASP: Assignment of Administration Special Access Code
4. Data Sheet
(a) Service Code (SRV = SSC) 
Note:When Split Call Forwarding is in service (the ASYD command. SYS1 INDEX79 bit2=1), this access code is used for
Split Call Forwarding.
TENANT 
NUMBER
 (TN)
ACCESS CODE
(ACC)MAXIMUM6 DIGITS
CONNECTION STATUS 
INDEX
(CI) N/H/B
KIND OFSERVICE 
(SRV)
SERVICE
INDEX(SID)1 – 63
NUMBER OF 
NECESSARY
DIGITS 
(NND)
NUMBER OF 
NECESSARY
DIGIT FOR 
SPEED 
CALLING
(NND1)
1 – 24
SERVICE CONTENTS
HHookingSSC1Call Hold
NNormalSSC2Dial Access to Attendant 
(Information Service Call)
HHooking
BBusySSC3Call Back; Entry
BBusySSC4Executive Right of Way
NNormalSSC5Call Waiting – OriginatingBBusy
NNormalSSC6Call Back; Cancel
NNormalSSC7Call Pickup – Group
NNormalSSC8
C.F. – All Calls/Split C.F. – 
All Calls (for C.O./Tie);
Entry     Note
NNormalSSC9
C.F. – All Calls/Split C.F. – 
All Calls (for C.O./Tie); 
Cancel   Note
NNormalSSC10
C.F. – Busy Line/Split C.F. – 
Busy Line (for C.O./Tie); 
Entry   Note
NNormalSSC11
C.F. – Busy Line/Split C.F. – 
Busy Line (for C.O./Tie);
Cancel     Note
NNormalSSC12
C.F. – Don’t Answer/Split 
C.F.
 – Don’t Answer
(for C.O./Tie); Entry     Note
NNormalSSC13
C.F. – Don’t Answer/Split 
C.F.
 – Don’t Answer
(for C.O./Tie); Cancel   Note
NNormalSSC14Speed Calling – Station; 
Entry
NNormalSSC15Speed Calling – System; 
Access