NEC Neax 2400 Imx System Operations And Maintenance Manual

CHAPTER 6 NDA-24238
Page 434
Revision 3.0
SYSTEM OPERATIONS
9.3 Office Data Management Procedure
The procedure generally taken when changing the office data is shown below. If your system uses software
Release 1 or 2, refer to Figure 6-25. If the software is Release 3 or later, refer to Figure 6-26.
For systems using software Release 1 or 2
Figure 6-25   Office Data Change Procedure (for Release 1 or 2)
HDD_MAT command Note
Direction Select : Verify HDD against MAT
Data Type Select : Data Memory, etc....

NDA-24238 CHAPTER 6
Page 435
Revision 3.0
SYSTEM OPERATIONS
For systems using software Release 3 or Later
Figure 6-26   Office Data Change Procedure (for Release 3 or Later)
HDD_FDD command Note
System Select : HFD0/HFD1
Direction Select : Verify HDD against FDD
Data Type Select : Data Memory, etc.
MEM_HDD command Note
Direction Select : Verify HDD against MEM
Data Type Select : Data Memory, etc. Entry Into Office Data Programming Sheets
MEM_HDD command Note
Direction Select : Memory to Hard Disk
Data...

CHAPTER 6 NDA-24238
Page 436
Revision 3.0
SYSTEM OPERATIONS
Figure 6-27 shows the function of three backup commands: HDD to FDD, HDD to MAT, and MEM to
HDD.
Figure 6-27   Backup Commands
NECNEAX 2400 IMS
MAT
HDD
FD FDDFDDMEMPBX
HDD_FDD
DM:	Data Memory
NDM:	Network Data Memory
LDM: 	Local Data Memory
ND: 	Name Display Data
RCF:	Wireless Call Forwarding Data
CF:	Call Forwarding Data
SPD:	Speed Calling-System Data
USK:	User Assign Soft Key Data  (for Release 3 or later)
NS:	Number Sharing Data  (for...

NDA-24238 CHAPTER 6
Page 437
Revision 3.0
SYSTEM OPERATIONS
9.4 Call Forwarding Data/Individual Speed Calling Data Management
Call Forwarding Data and Individual Speed Calling Data are changed at any time because these services
are set/cancelled from the station involved. In the PBX, these data are backed up by FD.
Call Forwarding Data:  HDD_MAT command
Individual Speed Calling Data: HDD_MAT command
9.5 One-Touch Speed Call Memory Data Management
One-Touch Speed Call Memory data of D
term is destroyed...

CHAPTER 6 NDA-24238
Page 438
Revision 3.0
SYSTEM OPERATIONS
10. TEST OPERATIONS OF VARIOUS KINDS
This section explains the methods of test operations (shown in Figure 6-28) to be performed in case a fault
recovery occurs.
Figure 6-28   Test Operation Method Examples
COMMAND COMMAND FULL NAME
DCON Display of Connection Status Display of connection status of designated station/trunk
Test connection by designating trunks, tones, and ringback tone from test station
10.1  Designated Connection Test (Station)...

NDA-24238 CHAPTER 6
Page 439
Revision 3.0
SYSTEM OPERATIONS
10.1 Designated Connection Test (Station)
(1) General
The purpose of this test is to confirm the operations related to a trunk or tone that is designated from the
test station. Refer to Ta b l e  6 - 6. The test result displays on the MAT screen as system message [6-I].
(2) Precaution
Designated connection to a trunk—A designated connection to trunk is limited only to an individual line
of either 2nd DT system or sender system.
Table 6-6...

CHAPTER 6 NDA-24238
Page 440
Revision 3.0
SYSTEM OPERATIONS
(3) Designated Connection Test Procedure
(a) Register Test Procedure
Figure 6-29   Register Test Procedure/Connection Diagram
 Access code is assigned by ASPA command, CI=N,
SRV=SSC, SID=17
 Route numbers to be designated are as follows.:
 If any of the dialed numbers are not received correctly, a
Reorder Tone (ROT) is heard.
RT NUMBER
902
903
TRUNK NAME
Originating Register Trunk
Incoming Register Trunk
Hang Up
TRUNK DESIGNATIONTEST IN...

NDA-24238 CHAPTER 6
Page 441
Revision 3.0
SYSTEM OPERATIONS
(b) Sender Test Procedure
Figure 6-30   Sender Test Procedure/Connection Diagram
 Access code is assigned by ASPA command, CI=N,
SRV=SSC, SID=17
 Route number to be designated is as follows:
 If any of the dialed numbers are received correctly, a Reorder
Tone (ROT) is heard.
RT NUMBER
905
TRUNK NAME
Sender Trunk DP/PB
Hang Up
Note 1:
After the sender to be tested is connected to the register, the sender sends out 1 ~ 9, 0 by DP
signals and 1...

CHAPTER 6 NDA-24238
Page 442
Revision 3.0
SYSTEM OPERATIONS
(c) 3-Party Conference Trunk Test Procedure
Figure 6-31   3-Party Conference Test Procedure
Note:If the trunk number of the next 3-Party Conference Trunk is not assigned, the test ends.
 Access code is assigned by ASPA command, CI=N,
SRV=SSC, SID=17
  Route numbers to be designated are as follows:
RT NUMBER
909
913
TRUNK NAME
3-party conference trunk
(for station, ATTCON, trunk)
3-party conference trunk
(only for ATTCON)
+ “9xx”
RT No.“xxx”...

NDA-24238 CHAPTER 6
Page 443
Revision 3.0
SYSTEM OPERATIONS
Figure 6-32   3-Party Conference Test Connection Diagram
TSTT TSTT TSTTTSTT TSTT TSTT ORTSST TRUNK DESIGNATION TEST IN PROGRESS
1 SEC.1 SEC.1 SEC.1 SEC.
1 SEC.
1 SEC.
1 SEC. 1 SEC.
(DT) (SST) (DT)
(SST) (DT) (SST)