NEC Neax 2400 Imx System Operations And Maintenance Manual

CHAPTER 6 NDA-24238
Page 424
Revision 3.0
SYSTEM OPERATIONS
(2) Identifier 2: Sending Data Text
A text for sending billing data in response to “(1) Data Request Text” from the client.
Text sending direction: Client   Server
The number of billing data records is 64 or less.
(3) Identifier 3: Server Response Text
A text to be sent to the client when there is no billing data to send in response to “(1) Data Request Text”
or as a response to a “(5) Status Monitoring Text.”
Text sending direction: Client...

NDA-24238 CHAPTER 6
Page 425
Revision 3.0
SYSTEM OPERATIONS
(5) Identifier 5: Status Monitoring Text
A text for use in monitoring the server status from the client’s viewpoint or the client from the server’s
viewpoint. At the same time, the text is used to notify the server of the client status.
Text sending direction: Client   Server
(6) Identifier 6: Connection Disconnect Text
A text to be sent from the client to the server to disconnect the connection. In response to this text, the
server promptly...

CHAPTER 6 NDA-24238
Page 426
Revision 3.0
SYSTEM OPERATIONS
Note:
Asterisk (*) identifies the traffic measurements that can be saved on the HD of the MAT.
4* ATTCON Peg Count Measurement of the number of each type of call handled at the ATTCON/
DESKCON.
5* Route  Peg  Count Measurement of the number of various types of call connections on a per route basis. 
6 Service Peg Count Measurement of the number of times the following services are operated:
Call Hold
Call Back
Executive Right of Way
Call Waiting...

NDA-24238 CHAPTER 6
Page 427
Revision 3.0
SYSTEM OPERATIONS
8.2 Operating Procedure 
1. Procedure for Set-up and Start
The procedure to set up and start the traffic measurement is as follows:
STEP 1
By using the ASYD/ASYDN command, assign the necessary system data as follows:
When performing traffic measurement on a node basis:
 SYS1, INDEX8 (Number of Tenants)
 SYS1, INDEX9 (Number of Attendant Consoles)
 SYS1, INDEX47, bit 0 (Unit of Traffic Measurement):  0/1 = CCS/Erlang
 SYS1, INDEX47, bit 7...

CHAPTER 6 NDA-24238
Page 428
Revision 3.0
SYSTEM OPERATIONS
Figure 6-21   IMX “MAT Menu” Display Image (Example)
Figure 6-21 shows the IMX “MAT Menu” display image. The display should look similar to the following:
Scan New Alarms/Traffic
Office Name (assigned by ASYD/AOFC command
Collect New Alarms
Collect New Traffic
Abor t Data Collections
View Scanning Log
Major Alarm Indicator
Minor Alarm Indicator
Supervisory Message Indicator
Traffic Data Indicator
About
Log Manager
Log out
Configure
Log in...

NDA-24238 CHAPTER 6
Page 429
Revision 3.0
SYSTEM OPERATIONS
(2) Data Output - Details on DTFD/DTFDN Command
To obtain the collected Traffic data, you can use the “DTFxxx” or “DTFxxxN” command as shown below.
The commands can be activated by your direct log-in operation onto the MAT, but in normal cases, the com-
mands are to be activated automatically at predetermined intervals assigned by the ATRF/ATRFN command.
Also, each command below corresponds to the Traffic Measurement “TYPE” assigned by the...

CHAPTER 6 NDA-24238
Page 430
Revision 3.0
SYSTEM OPERATIONS
Figure 6-22   DTFD Command Display Image (Example)
Figure 6-22 shows the DTFD command display image (example). The DTFD/DTFDN command should look
similiar to this.
Traffic Data
Check box to specify the “Traffic Data” 
TYPE.
Data collecting Log
This area displays the current Traffic 
Measurement data, based on the selected 
“Traffic Data” TYPE.
Tool Buttons
 Collect Data
Used to collect the Traffic report with regard to the selected “Traffic...

NDA-24238 CHAPTER 6
Page 431
Revision 3.0
SYSTEM OPERATIONS
Figure 6-23   “Listup Report” Window when “View Database” is Selected (Example)
Figure 6-24   “Export” Dialog for Traffic Report Text File Saving
Form at:Destination:
OKCancel
Disk fileCharacter separated values
Export
The dialog box, as shown below, appears, if the “Save Text File” button is selected on the “Listup Report” window 
(see Figure 6-23 above). If the file is to be saved:
1.  Select “Character-separated values” on the “Format”
 list...

CHAPTER 6 NDA-24238
Page 432
Revision 3.0
SYSTEM OPERATIONS
(3) Service Conditions (when performing Traffic Measurement via TCP/IP)
(a) The NDM (network-level) data for the traffic measurement order is replaced/updated, at each time
the system is initialized or data change is requested from the ATRFN command.
(b) When the network-level data is once assigned via the ATRFN command, the node-level data for
ATRF command cannot be changed or modified.
(c) When the network-level data is once assigned via the...

NDA-24238 CHAPTER 6
Page 433
Revision 3.0
SYSTEM OPERATIONS
9. OFFICE DATA MANAGEMENT
This section explains how to manage various kinds of data such as Call Forwarding Data, Individual Speed
Calling Data, and Office Data, etc.
9.1 Office Data Stored Locations
The office data is stored in the memory (MEM) and on the Hard Disk (HD). While the system is in service,
it operates by the office data stored in the memory. Should the contents of the office data be destroyed due
to trouble, the system restarts its...