NEC Neax 2400 Imx Fusion Network System Manual

CHAPTER 8 ND-70185 (E)
Page 176
Revision 3.0
EX- FCCS
EX-FCCS Features
3. The node that requires the data programming or data change for Number Portability depends on the
pattern. See Figure 8-5 and Table 8-2 that explain the eight patterns.
Figure 8-5   Patterns of Number Portability
Note 1:
Destination node
Note 2:Node to be connected to the FUG where the new number is added
Note 3:Node where Telephone Number is located before the Number Portability activation
4. Telephone Numbers used in the other FUG...

ND-70185 (E) CHAPTER 8
Page 177
Revision 3.0
EX- FCCS
EX-FCCS Features
5. Up to a maximum of 120,000 Telephone Numbers may be assigned in the entire Enhanced CCIS/EX-
FCCS network (including Telephone Numbers in the NEAX2000 IVS2) and a maximum of 48,000
per FUG (not to exceed 120,000 per total network). 
3.2 Centralized-MAT for EX-FCCS
[Centralized Maintenance]
(a) NEAX2000 IVS
2
1. MAT software for NEAX2400 IMX system and NEAX2000 IVS2 system are installed on a PC called
the “MAT.” Depending on the...

CHAPTER 8 ND-70185 (E)
Page 178
Revision 3.0
EX- FCCS
EX-FCCS Features
[Centralized Traffic Collecting]
1. The feature to collect traffic information of NEAX2000 IVS
2 system is activated by logging in to the
NEAX2000 IVS2 node with Centralized-MAT for EX-FCCS using the traffic collecting command
dedicated for NEAX2000 IVS2 system.
2. For IMX systems, logging in to the NCN of each FUG with Centralized-MAT activates the feature to
collect traffic information.
[Centralized System Management Report]
1. This...

ND-70185 (E) CHAPTER 8
Page 179
Revision 3.0
EX- FCCS
EX-FCCS Features
7. When the fault information occurring at all FUGs is managed by the Centralized-MAT for EX-FCCS,
the destination for the output of the fault message must be changed to the designated Center Office
(for example, NCN) at each LN (including NEAX2000 IVS
2 System). See Figure 8-6.
Figure 8-6   Centralized Maintenance - EX-FCCS
W hen collecting the fault information of nodes (including the connected NEAX2000IVS ) at each FUG,  
 
When...

CHAPTER 8 ND-70185 (E)
Page 180
Revision 3.0
EX- FCCS
EX-FCCS Features
3.3 CCIS Features Activated with EX-FCCS
1. CCIS features in Table 8-4 are available in EX-FCCS network.
Table 8-4 CCIS Service in EX-FCCS Network
Note:
Telephone Numbers should be used for activating CCIS services through the network.
Note 1:This feature is available on the condition that the NEAX2000 IVS2 is the satellite office.
Note 2:This feature is available for calling number display only
FEATURE
CODEFEATURE NAMENETWORK...

ND-70185 (E) CHAPTER 8
Page 181
Revision 3.0
EX- FCCS
EX-FCCS Features
2. Unique PCs (Point Codes) in the CCIS network connected with EX-FCCS are required. 
Figure 8-7   PC Assignment in EX-FCCS Network
3. The CCH to be used is selected as follows.
1) when the call is processed using the speech line (Bch), the outgoing/incoming route, Logical Route
(LRT), decides CCH.
LRT → PC → CSCG → CCH 
2) when the call is processed without speech line (Bch) - inter-office service such as CALL BACK,
MESSAGE WAITING...

CHAPTER 8 ND-70185 (E)
Page 182
Revision 3.0
EX- FCCS
EX-FCCS Features
3.4 Centralized Message Center Interface - EX-FCCS
This section explains the conditions of Centralized Message Center Interface feature within EX-FCCS Net-
work. This feature provides an interface to the external CPU for Message Center (MC) information when
a specified UCD group in the network is called. This interface allows external control of Message Waiting
Lamp (MWL) indications on equipped PBX stations.
Note:Calls terminated to...

ND-70185 (E) CHAPTER 8
Page 183
Revision 3.0
EX- FCCS
EX-FCCS Features
 Call Waiting Lamp Controll information is sent from the MCI within Center FUG to other Fusion
Groups and NEAX2000 IVS2 system via CCIS.
 When the Centralized Office adopts the ICS MCI format method, the receiving message field is output
as it is. When in the IMX MCI format method, the originating information field is also output to Tele-
phone Number field.
FUG1 (Center FUG)
Node
ANode
CNode
DNode
E
MCIMCI FUG2
IVS
UCDUCD
UCD
Node...

CHAPTER 8 ND-70185 (E)
Page 184
Revision 3.0
EX- FCCS
EX-FCCS Features
3.5 Centralized Billing - EX-FCCS (Polling Method)
This section explains the conditions of Centralized Billing feature within EX-FCCS Network.
 Two methods of administering Centralized Billing information are available: either the CCIS billing
method or the FCCS billing method.
 When a 7-digit or 8-digit EX-FCCS Telephone Number is used in the network, for the NEAX2000
IVS
2 system, the EX-FCCS Telephone Number is output to Station...

ND-70185 (E) CHAPTER 8
Page 185
Revision 3.0
EX- FCCS
Data Programming
4. Data Programming
This section explains how to assign a brand-new EX-FCCS network data.
There are some conditions for data programming to be required for EX-FCCS.
1. When connecting a stand-alone NEAX2400 IMX, non-fusion system (via EX-FCCS) or a NEAX2000
IVS
2 using  Enhanced CCIS feature to an existing FUG:
(a) The system must be the NCN.
(b) The system is programmed as the Fusion Network configured by one NCN only.
(c) Use the...