NEC Neax 2000 Ivs2 Q-Sig System Manual
Here you can view all the pages of manual NEC Neax 2000 Ivs2 Q-Sig System Manual. The NEC manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 61
CHAPTER 4 CIRCUIT CARD INFORMATION List of Required Circuit Card NEAX2000 IVS2 Q-SIG System Manual ND-70923 (E), Issue 1.0 Page 55 NOTE 3:Set the SW-1 and SW-2 as follows: NOTE 4:When the PBX is a clock source office, set the SW-1 and SW-2 on all the DTI cards mounted in PIM0 to “OFF”. NOTE 5:Mount the DTI card which receives a source clock signal into PIM0. CONDITIONSDTI0 DTI1 DTI2 DTI3 REMARKS SW -1SW -2SW -1SW -2SW -1SW -2SW -1SW -2 When one DTI is provided.ON OFF – – – – – –MP card will...
Page 62
NEAX2000 IVS2 Q-SIG System ManualPage 56 ND-70923 (E), Issue 1.0 CHAPTER 4 CIRCUIT CARD INFORMATION List of Required Circuit Card PN-24DTA-C (DTI) Locations of Lamps, Switches, and Connectors SENSE RUN MB CRC PCM FRM RMT AIS BL SW1 SW0 JRR1 AISS MAS JPR0 JPS
Page 63
CHAPTER 4 CIRCUIT CARD INFORMATION List of Required Circuit Card NEAX2000 IVS2 Q-SIG System Manual ND-70923 (E), Issue 1.0 Page 57 Lamp Indications LAMP NAMECOLOR FUNCTION RUN Green Flashes at 120 IPM while this card is operating normally. CRC Red Remains lit when detecting Cyclic Redundancy Checking (CRC) errors. PCM Red Remains lit when detecting PCM signal loss. FRM Red Remains lit when detecting Frame Alignment signal loss. RMT Red Remains lit when receiving Frame Alignment signal loss alarm...
Page 64
NEAX2000 IVS2 Q-SIG System ManualPage 58 ND-70923 (E), Issue 1.0 CHAPTER 4 CIRCUIT CARD INFORMATION List of Required Circuit Card Switch Settings SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SENSE (Rotary SW) NOTE 10-3 Not used 4-F Set the switch to match the AP Number (04-31) to be set by CM05. MB (Toggle SW) NOTE 2UP For make-busy For normal operation (Continued) F 4 AP No.SW1-4: ON 04 05 06 07 08 09 10 11 12 13 14 15 SW1-4: OFF 20 21 22 23 24 25 26 27 28 29 30 31 SW No. 456789ABCDEF ON...
Page 65
CHAPTER 4 CIRCUIT CARD INFORMATION List of Required Circuit Card NEAX2000 IVS2 Q-SIG System Manual ND-70923 (E), Issue 1.0 Page 59 SW0 (Piano Key SW) 1 NOTE 3 NOTE 4ONSource clock signal from network is sent to the PLO 0 input on MP card. OFFSource clock signal from network is not sent to the PLO 0 input on MP card. 2 NOTE 3 NOTE 4ONSource clock signal from network is sent to the PLO 1 input on MP card. OFFSource clock signal from network is not sent to the PLO 1 input on MP card....
Page 66
NEAX2000 IVS2 Q-SIG System ManualPage 60 ND-70923 (E), Issue 1.0 CHAPTER 4 CIRCUIT CARD INFORMATION List of Required Circuit Card The figure in the SWITCH NAME column and the position in in the SETTING POSITION- column indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned.SW1 (Piano Key SW) NOTE 41 Not used 2 Not used 3 Not used 4ON AP No. 04-15 OFF AP No. 20-31 JPR0 (Jumper pin) UPNeutral...
Page 67
CHAPTER 4 CIRCUIT CARD INFORMATION List of Required Circuit Card NEAX2000 IVS2 Q-SIG System Manual ND-70923 (E), Issue 1.0 Page 61 NOTE 1:Set the groove on the switch to the desired position. NOTE 2:When the power is on, flip the MB switch to ON (UP position) before plugging/ unplugging the circuit card. NOTE 3:Set SW0-1 and SW0-2 as follows: NOTE 4:When the PBX is a clock source office, set the SW0-1 and SW0-2 on all the DTI cards mounted in PIM0 to “OFF”. NOTE 5:Mount the DTI card which receives...
Page 68
NEAX2000 IVS2 Q-SIG System ManualPage 62 ND-70923 (E), Issue 1.0 CHAPTER 4 CIRCUIT CARD INFORMATION List of Required Circuit Card PN-SC01 (DCH) Locations of Lamps, Switches and Connectors Lamp Indications LAMP NAMECOLOR FUNCTION RUN Green Flashes at 120 IPM while this card is operating normally. LC Green Remains lit when communications are normally ongoing with the D Channel data links connected. LPB Green Not used SENS RUN MB SW0 LC LPB SW1
Page 69
CHAPTER 4 CIRCUIT CARD INFORMATION List of Required Circuit Card NEAX2000 IVS2 Q-SIG System Manual ND-70923 (E), Issue 1.0 Page 63 Switch Settings SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SENS (Rotary SW) NOTE 14-F Set the switch to match the AP Number (04-31) to be set by CM05. 0-3 Not used MB (Toggle SW) NOTE 2UP For make-busy For normal operation SW0 (Piano Key SW)1 Always set to OFF 2 Always set to OFF 3 Always set to OFF 4ON AP No. 04-15 OFF AP No. 20-31 (Continued) F 4 AP...
Page 70
NEAX2000 IVS2 Q-SIG System ManualPage 64 ND-70923 (E), Issue 1.0 CHAPTER 4 CIRCUIT CARD INFORMATION List of Required Circuit Card The figure in the SWITCH NAME column and the position in in the SETTING POSITION column indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. NOTE 1:Set the groove on the switch to the desired position. NOTE 2:When the power is on, flip the MB switch to ON (UP...