NEC Neax 2000 Ivs2 Q-Sig System Manual
Here you can view all the pages of manual NEC Neax 2000 Ivs2 Q-Sig System Manual. The NEC manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 51
CHAPTER 4 CIRCUIT CARD INFORMATION List of Required Circuit Card NEAX2000 IVS2 Q-SIG System Manual ND-70923 (E), Issue 1.0 Page 45 PN-CP14 (MP) Locations of Lamps, Switches, and Connectors CONN: To CONNR connector on PZ-M537 (EXPMEM) Lamp Indications LAMP NAMECOLOR FUNCTION RUN Green Flashes at 120 IPM while this card is operating normally. CLK Green Remains lit while receiving clock signals to the PLO. SW3 RUN SW1 SW2 CLK VR DK JACK CONNSW4 JP0JP1 RS1 RS0
Page 52
NEAX2000 IVS2 Q-SIG System ManualPage 46 ND-70923 (E), Issue 1.0 CHAPTER 4 CIRCUIT CARD INFORMATION List of Required Circuit Card Switch Settings NOTE 1:Set the groove on the switch to the desired position. NOTE 2:Only when executing “MP Program Download” in MATWorX, set the SW3 to 5-8. Caution When the operating power is being supplied to this circuit card, do not plug/unplug this circuit card into/from its mounting slot. SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SW3 (Rotary SW) NOTE...
Page 53
CHAPTER 4 CIRCUIT CARD INFORMATION List of Required Circuit Card NEAX2000 IVS2 Q-SIG System Manual ND-70923 (E), Issue 1.0 Page 47 SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SW1 (Push SW) For initializing CPU SW2 (Piano Key SW)1ON A-law (Australia) OFF µ-law (North America) 2, 3Selection of PLO0 input (Phase Locked Oscillator) For clock receiver office: For clock source office: SW2-2 SW2-3 OFF OFF 4ONWhen using RS1 port for built-in MODEM OFF When using RS1 port for RS-232C...
Page 54
NEAX2000 IVS2 Q-SIG System ManualPage 48 ND-70923 (E), Issue 1.0 CHAPTER 4 CIRCUIT CARD INFORMATION List of Required Circuit Card SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SW4 (Dip SW) 1 Not used 2 Not used 3, 4Selection of PLO1 input (Phase Locked Oscillator) For clock receiver office: For clock source office: SW4-3 SW4-4 OFF OFF VR (Rotary SW) Variable Resister for External Hold Tone Source (0 - 20 Kohms : Clockwise) DK (Connector) 02 Ground detection 01 Ground sending...
Page 55
CHAPTER 4 CIRCUIT CARD INFORMATION List of Required Circuit Card NEAX2000 IVS2 Q-SIG System Manual ND-70923 (E), Issue 1.0 Page 49 The figure in the SWITCH NAME column and the position in in the SETTING POSITION column indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK JP0 (Jumper pin) UPNot used (Memory backup OFF) For normal...
Page 56
NEAX2000 IVS2 Q-SIG System ManualPage 50 ND-70923 (E), Issue 1.0 CHAPTER 4 CIRCUIT CARD INFORMATION List of Required Circuit Card PN-30DTC-A (DTI) Locations of Lamps, Switches and Connectors SENS RUN MB SW PCM FRM MFRM RMT MRMT AIS BL JP JPSJPR
Page 57
CHAPTER 4 CIRCUIT CARD INFORMATION List of Required Circuit Card NEAX2000 IVS2 Q-SIG System Manual ND-70923 (E), Issue 1.0 Page 51 Lamp Indications LAMP NAMECOLOR FUNCTION RUN Green Flashes at 120 IPM when this card is normally operating. PCM Red Remains lit when detecting PCM signal loss. FRM Red Remains lit when detecting Frame Alignment signal loss. MFRM Red Remains lit when detecting Multi-Frame Alignment signal loss on time Slot 16. RMT Red Remains lit when receiving the alarm from a...
Page 58
NEAX2000 IVS2 Q-SIG System ManualPage 52 ND-70923 (E), Issue 1.0 CHAPTER 4 CIRCUIT CARD INFORMATION List of Required Circuit Card Switch Settings SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SENS (Rotary SW) NOTE 14-F Set the switch to match the AP Number (04-31) to be set by CM05. 0-3 Not used MB (Toggle SW) NOTE 2UP For make-busy For normal operation (Continued) F 4 AP No.SW-8: ON 04 05 06 07 08 09 10 11 12 13 14 15 SW-8: OFF 20 21 22 23 24 25 26 27 28 29 30 31 SW No. 456789ABCDEF ON DOWN
Page 59
CHAPTER 4 CIRCUIT CARD INFORMATION List of Required Circuit Card NEAX2000 IVS2 Q-SIG System Manual ND-70923 (E), Issue 1.0 Page 53 SW (Piano Key SW) 1 NOTE 3 NOTE 4ONSource clock signal from network is sent to the PLO 0 input on MP card. OFFSource clock signal from network is not sent to the PLO 0 input on MP card 2 NOTE 3 NOTE 4ONSource clock signal from network is sent to the PLO 1 input on MP card. OFFSource clock signal from network is not sent to the PLO 1 input on MP card. 3ON Remote...
Page 60
NEAX2000 IVS2 Q-SIG System ManualPage 54 ND-70923 (E), Issue 1.0 CHAPTER 4 CIRCUIT CARD INFORMATION List of Required Circuit Card The figure in the SWITCH NAME column and the position in in the SETTING POSITION column indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. NOTE 1:Set the groove on the switch to the desired position. NOTE 2:When the power is on, flip the MB switch to ON (UP...