NEC Neax 2000 Ivs2 Data Interface System Manual
Have a look at the manual NEC Neax 2000 Ivs2 Data Interface System Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
CHAPTER 5 CIRCUIT CARD INFORMATION Mounting Location of Circuit Card NEAX2000 IVS2 Data Interface System Manual ND-70924 (E), Issue 1.0 Page 65 MOUNTING LOCATION OF CIRCUIT CARD This section explains the conditions for mounting circuit cards for the Data Interface. Figure 5-1 shows circuit card mounting slots allocated in the PIM. Figure 5-1 Mounting Location of Circuit Card *1PN-CP14 (MP) card on the MP12 slot on PIM0. *2PN-24DTA-C/PN-30DTC-A (DTI) card on the AP00-AP11 slots on PIM0-PIM7. *3PN-2DPCB (DPC) and PN-M03 (M03) card on the LT00-LT11 slots on PIM0-PIM7. *4PZ-M542/PZ-M557 (CONN) card on the LTC0-LTC3 connectors on the PIM which accommodates 30DTI card. LT09/AP09LT08/AP08LT07/AP07 LT C 1LT C 0LT C 2 BWB PIM 0~7 FRONTAC/DC PWR LT10/AP10LT00/AP00LT01/AP01LT02/AP02LT03/AP03LT04/AP04LT05/AP05LT06/AP06LT11/AP11/FP11MP12/FP12 LT C 3 DC/DC PWR PFTVM *2, *3*1 *4
NEAX2000 IVS2 Data Interface System ManualPage 66 ND-70924 (E), Issue 1.0 CHAPTER 5 CIRCUIT CARD INFORMATION List of Required Circuit Cards LIST OF REQUIRED CIRCUIT CARDS Table 5-1 shows the required circuit cards to be explained in this section. *MB = Make Busy Table 5-1 List of Required Circuit Cards NAME (FUNCTIONAL NAME) LAMP X: PROVIDED –: NOT PROVIDEDSWITCH X: PROVIDED –: NOT PROVIDEDEXTRACTION/ INSERTION WITH POWER ON X: ALLOWED : ALLOWED AFTER MB* –: NOT ALLOWED REFERENCE PAGE PN-CP14 (MP) X X –Page 67 PN-24DTA-C (DTI) X XPage 72 PN-30DTC-A (DTI) X XPage 78 PZ-M542 (CONN) – X XPage 84 PZ-M557 (CONN) – X XPage 86 PN-2DPCB (DPC) X X XPage 88 PN-M03 (M03) X X XPage 92
CHAPTER 5 CIRCUIT CARD INFORMATION List of Required Circuit Cards NEAX2000 IVS2 Data Interface System Manual ND-70924 (E), Issue 1.0 Page 67 PN-CP14 (MP) Locations of Lamps, Switches, and Connectors CONN: To CONNR connector on PZ-M537 (EXPMEM) Lamp Indications LAMP NAMECOLOR FUNCTION RUN Green Flashes at 120 IPM while this card is operating normally. CLK Green Remains lit while receiving clock signals to the PLO. SW3 RUN SW1 SW2 CLK VR DK JACK CONNSW4 JP0JP1 RS1 RS0
NEAX2000 IVS2 Data Interface System ManualPage 68 ND-70924 (E), Issue 1.0 CHAPTER 5 CIRCUIT CARD INFORMATION List of Required Circuit Cards Switch Settings NOTE 1:Set the groove on the switch to the desired position. NOTE 2:Only when executing “MP Program Download” in MATWorX, set the SW3 to 5-8. CAUTION When the operating power is being supplied to this circuit card, do not plug/unplug this circuit card into/from its mounting slot. SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SW3 (Rotary SW) NOTE 1 0-FOn Line (Call processing is in progress) 2Off Line (Call processing is stopped) I/O port: As per CM40 YY=08 3Off Line (Call processing is stopped) I/O port: 9600bps (Fixed) 5 NOTE 2Off Line (Call processing is stopped) I/O port: 9600bps 6 NOTE 2Off Line (Call processing is stopped) I/O port: 19200bps 7 NOTE 2Off Line (Call processing is stopped) I/O port: 38400bps 8 NOTE 2Off Line (Call processing is stopped) I/O port: 57600bps B For clearing the office data CFor setting the resident system program 1, 4, 9 A, D-FNot used (Continued) 0 0
CHAPTER 5 CIRCUIT CARD INFORMATION List of Required Circuit Cards NEAX2000 IVS2 Data Interface System Manual ND-70924 (E), Issue 1.0 Page 69 SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SW1 (Push SW) For initializing CPU SW2 (Piano Key SW)1ON A-law (Australia) OFF µ-law (North America) 2, 3Selection of PLO0 input (Phase Locked Oscillator) For clock receiver office: For clock source office: SW2-2 SW2-3 OFF OFF 4ONWhen using RS1 port for built-in MODEM OFF When using RS1 port for RS-232C (Continued) 4 3 2 1 OFF ONSW2-2 SW2-3 FUNCTION OFF OFF 1.5 MHz clock [For PN-24DTA-C/PN-24PRTA] ON OFF 192 kHz clock [For PN-BRTA] OFF ON 2 MHz clock [For PN-30DTC-A/PN-2BRTC] ON ON Not used
NEAX2000 IVS2 Data Interface System ManualPage 70 ND-70924 (E), Issue 1.0 CHAPTER 5 CIRCUIT CARD INFORMATION List of Required Circuit Cards SWITCH NAMESWITCH NUMBERSETTING POSITIO NFUNCTION CHECK SW4 (Dip SW) 1Not used 2Not used 3, 4Selection of PLO1 input (Phase Locked Oscillator) For clock receiver office: For clock source office: SW4-3 SW4-4 OFF OFF VR (Rotary SW) Variable Resister for External Hold Tone Source (0 - 20 Kohms : Clockwise) DK (Connector) 02 Ground detection 01 Ground sending (Continued) 1 23 4ON OFF OFF SW4-3 SW4-4 FUNCTION OFF OFF 1.5 MHz clock [For PN-24DTA-C/PN-24PRTA] ON OFF 192 kHz clock [For PN-BRTA] OFF ON 2 MHz clock [For PN-30DTC-A/PN-2BRTC] ON ON Not used 20 0 01 02
CHAPTER 5 CIRCUIT CARD INFORMATION List of Required Circuit Cards NEAX2000 IVS2 Data Interface System Manual ND-70924 (E), Issue 1.0 Page 71 The figure in the SWITCH NAME column and the position in in the SETTING POSITION column indicate the standard setting of the switch. When the switch is not set as shown by the figure and , the setting of the switch varies with the system concerned. SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK JP0 (Jumper pin) UPNot used (Memory backup OFF) For normal operation (Memory backup ON) JP1 (Jumper pin) For using internal tone source DOWN For using external tone source Fr o n tDOWN Fr o n t UP
NEAX2000 IVS2 Data Interface System ManualPage 72 ND-70924 (E), Issue 1.0 CHAPTER 5 CIRCUIT CARD INFORMATION List of Required Circuit Cards PN-24DTA-C (DTI) Locations of Lamps, Switches and Connectors SENSE RUN MB CRC PCM FRM RMT AIS BL SW1 SW0 JRR1 AISS MAS JPR0 JPS
CHAPTER 5 CIRCUIT CARD INFORMATION List of Required Circuit Cards NEAX2000 IVS2 Data Interface System Manual ND-70924 (E), Issue 1.0 Page 73 Lamp Indications LAMP NAMECOLOR FUNCTION RUN Green Flashes at 120 IPM while this card is operating normally. CRC Red Remains lit when detecting Cyclic Redundancy Checking (CRC) errors. PCM Red Remains lit when detecting PCM signal loss. FRM Red Remains lit when detecting Frame Alignment signal loss. RMT Red Remains lit when receiving Frame Alignment signal loss alarm from a distant office. AIS Red Remains lit when a pattern of consecutive “1” is received. The distant office transmits this signal for a loop-back test. BL Red B channel status ON : More than 10 channels are busy OFF : All channels are idle Flash (60 IPM) : Only one channel is busy Flash (120 IPM) : 2 through 10 channels are busy
NEAX2000 IVS2 Data Interface System ManualPage 74 ND-70924 (E), Issue 1.0 CHAPTER 5 CIRCUIT CARD INFORMATION List of Required Circuit Cards Switch Settings SWITCH NAMESWITCH NUMBERSETTING POSITIONFUNCTION CHECK SENSE (Rotary SW) NOTE 10-3 Not used 4-F Set the switch to match the AP Number (04-31) to be set by CM05. MB (Toggle SW) NOTE 2UP For make-busy For normal operation (Continued) F 4 AP No.SW1-4: ON04 05 06 07 08 09 10 11 12 13 14 15 SW1-4: OFF20 21 22 23 24 25 26 27 28 29 30 31 SW No.456789ABCDEF ON DOWN