NEC Neax 1000 Ivs Very Small Platform System Manual

 NDA-24219 CHAPTER 3
Page 107
Revision 2.0
NAP-200-008
Sheet 3/10
Switch Setting of Circuit Card
(3) Switch Setting (see Table 008-4)
Table 008-4  PN-CP03 (MP) Card Switch Settings
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SW3 (Rotary SW)
0 - FOn Line (Call processing is in progress)
2Off Line (Call processing is stopped)
• I/O port: Depending on CM40 YY=08
3Off Line (Call processing is stopped)
• I/O port: 1200bps (Fixed)
B For clearing office data
C For setting resident system program
1,...

CHAPTER 3 NDA-24219  
Page 108
Revision 2.0
NAP-200-008
Sheet 4/10
Switch Setting of Circuit Card
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION col-
umn indicate the standard setting of the switch. When the switch is not set as shown by the figure and
, the setting of the switch varies with the system concerned.
Note:Set the groove on the switch knob to the desired switch position.Table 008-4 PN-CP03 (MP) Card Switch Settings (Continued)
SWITCH NAMESWITCH...

 NDA-24219 CHAPTER 3
Page 109
Revision 2.0
NAP-200-008
Sheet 5/10
Switch Setting of Circuit Card
CAUTION:
When the operating power is being supplied to this circuit card, do not plug/unplug this circuit
card into/from its mounting slot.
3. PZ-PW86 (PWR)
(1) Locations of Lamps, Switches, and Connectors (see Figure 008-2)
Figure 008-2  PZ-PW86 (PWR) Card
FRONT VIEW BATT2 MN MJ
ONBATTERY
SIDE VIEW GND
–27V FG
OFFON
240VAC 100/120VAC 2ON
2
1 ON
SW301 START
SIG
1
SW1
BATT1
AC INPUTMODE
SW102
• PZ-PW86(C)
AT T...

CHAPTER 3 NDA-24219  
Page 110
Revision 2.0
NAP-200-008
Sheet 6/10
Switch Setting of Circuit Card
Figure 008-2  PZ-PW86 (PWR) Card (Continued)
(2) Lamp Indications (see Table 008-5)
Table 008-5  PZ-PW86 (PWR) Card Lamp Indications
LAMP NAME COLOR FUNCTION
MJ Red Lights upon occurrence of a major fault.
MN Yellow Lights upon occurrence of a minor fault.
ON Green Remains lit while the power is on.
FRONT VIEWBATT2 MN MJ
ON
BATTERY
SIDE VIEW GND
–27V FG
OFFON 240VAC 100/120VAC2ON
2
1 ON SW102
START
SIG
1
SW1...

 NDA-24219 CHAPTER 3
Page 111
Revision 2.0
NAP-200-008
Sheet 7/10
Switch Setting of Circuit Card
(3) Switch Settings (see Table 008-6)
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION col-
umn indicate the standard setting of the switch. When the switch is not set as shown by the figure and
, the setting of the switch varies with the system concerned.
Table 008-6  PZ-PW86 (PWR) Card Switch Settings
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
Mode (Piano Key...

CHAPTER 3  NDA-24219    
NAP-200-008
FRONT V IEW
ST ART
SW1
SW102
BATT0
CN103 

 NDA-24219   CHAPTER 3
NAP-2 00-008
ON (–) 

CHAPTER 3  NDA-24219    
NAP-200-008
BL7BL6 

 NDA-24219 CHAPTER 3
Page 115
Revision 2.0
NAP-200-009
Sheet 1/3
Mounting Circuit Cards
1. MOUNTING PROCEDURE
(1) For testing, turn on “SW1” switch on the PZ-PW86/PZ-PW112 card. Make sure that “ON” lamp (green) is
lit. See Figure 009-1.
(2) Turn off “SW1” switch.
Figure 009-1  PZ-PW86/PZ/PW112 Card Lamp Indication
PZ-PW86/PW112
ON
OFFSW SWITCH
ON LAMP (GREEN)MN
MJ
ON 

CHAPTER 3 NDA-24219  
Page 116
Revision 2.0
NAP-200-009
Sheet 2/3
Mounting Circuit Cards
(3) Before mounting the circuit cards, confirm the following items.
• Wrist Strap is connected Frame Ground.
• Switch setting of circuit cards is already completed (Refer to the Circuit Card Manual).
• “SW1” switch of PZ-PW86PZ/PW112 Card is turned off.
(4) Mount circuit cards into their mounting positions according to the “Bay Face Layout” and “Port Assign-
ment Table” given in the System Data Sheet.
Figure 009-2...