NEC Neax 1000 Ivs Very Small Platform System Manual

 NDA-24219 CHAPTER 3
Page 117
Revision 2.0
NAP-200-009
Sheet 3/3
Mounting Circuit Cards
(5) Install the Card Stopper according to the following procedure:
(a) Insert the left side of the Card Stopper to the slot for the Card Stopper as shown in Fig. of 
Figure 009-3.
(b) Loosen the attached screw for the Card Stopper, and hang the right side of the Card Stopper onto the
screw. Then, tighten the screw as shown in Fig. of Figure 009-3.
Figure 009-3  Installing Card Stopper
A
B
Fig. AFig. B
Fig. B Fig....

CHAPTER 3 NDA-24219  
Page 118
Revision 2.0
NAP-200-010
Sheet 1/7
System Initialization and 
System Data Entry
1. SYSTEM INITIALIZATION
• There are two methods for System Initialization. The first method is to Clear All Data, except LEN0000 as
a CAT terminal, and then program the System Data. The second method is to use the Resident System Pro-
gram, which causes the system to configure itself automatically to the default settings, wherever the line/
trunk cards are installed. Refer to the System Data...

 NDA-24219 CHAPTER 3
Page 119
Revision 2.0
NAP-200-010
Sheet 2/7
System Initialization and 
System Data Entry
2. SYSTEM DATA ENTRY
• There are two methods for data entry, both of which employ a Customer Administration Terminal (CAT)
or a Maintenance Administration Terminal (MAT).
2.1 CAT
Any multiline terminal can be assigned as a CAT terminal through programming. The multiline terminal can still be
used as a regular telephone when it is not in CAT mode. If the system is initialized by “C” (Resident...

CHAPTER 3 NDA-24219  
Page 120
Revision 2.0
NAP-200-010
Sheet 3/7
System Initialization and 
System Data Entry
To reset CAT mode:
While “COMMAND = -” is displayed on the LCD:
(1) Lift the handset (off hook)
- SPKR lamp turns off.
(2) Restore the handset (on hook)
- CNF, ANS lamps turn off.
- LCD returns to clock.
The 48-port Quick Install program allows the technician to set up the NEAX1000 IVS by completing a step-by-step
guide to install and program stations, line keys, and selective features into the...

 NDA-24219 CHAPTER 3
Page 121
Revision 2.0
NAP-200-010
Sheet 4/7
System Initialization and 
System Data Entry
(1) Programming Procedure for Music On Hold
For providing Hold Tone Source on the MP card:
For providing External Hold Tone Source through the MP card:
DESCRIPTION DATA
Select the music to be provided. (3) 183
(4) 0: Nocturne
1 : Minuet
Define the type of call to be provided with Hold Tone 
on the MP card.
Note:When using the MP card, set the JP1
switch to UP (Internal Hold Tone Source)..Y = 0...

CHAPTER 3 NDA-24219  
Page 122
Revision 2.0
NAP-200-010
Sheet 5/7
System Initialization and 
System Data Entry
For providing External Hold Tone Source through MP card:
• External Hold Tone Source provided locally
For connecting the External Hold Tone Source, plug the cable into the MP card jack. See Figure 0010-1.
Figure 0010-1  Connecting External Hold Tone Source
Set the switches on the MP card as shown in Figure 0010-2.
Figure 0010-2  MP Card Switch Setting
Note:To set Hold Tone Source on the MP card,...

 NDA-24219 CHAPTER 3
Page 123
Revision 2.0
NAP-200-010
Sheet 6/7
System Initialization and 
System Data Entry
(2) Programming Procedure for Pushbutton Calling
DESCRIPTION DATA
Assign the Card Number of internal PB Receiver to 
the LEN No. 0124.
Note:When using the internal PB Receiver on
the MP card, assign the Card No. E200-
E203 to the LEN No. 0124.
If resident load is used, PB Receiver ports
(E200-LENS 0124) are automatically as-
signed.(1) LEN: 0124
(2) E200-E203 (PB Receiver No.)
Assign the type of...

CHAPTER 3 NDA-24219  
Page 124
Revision 2.0
NAP-200-010
Sheet 7/7
System Initialization and 
System Data Entry
DESCRIPTION DATA
Assign the type of signaling (DTMF) for Outgoing 
and Bothway Trunk Routes..YY = 01
(1) Trunk Route No. (00 - 63)
(2) 7
Specify the DTMF Sender characteristics to match 
the distant office..YY = 24 (DTMF Inter Digital Pause)
(1) Trunk Route No. (00 - 63)
.YY = 26 (DTMF Sender Signal Width)
(1) Trunk Route No. (00 - 63)
(2) 0/1 : 64ms/128ms
.YY = 46 (DTMF Sender Release Timing)...

 NDA-24219 CHAPTER 3
Page 125
Revision 2.0
NAP-200-011
Sheet 1/1
Operation Test
1. OPERATION TEST
Confirm the entered system data and hardware, including cable connection, by completing the following operational
tests.
• Basic Connection Test at MDF
- Station Line Test (Operator Call from all stations)
- Central Office Trunk Test (Incoming, Outgoing)
- Tie Line Trunk Test (Incoming, Outgoing)
• Service Feature Test
- Call Transfer
-Step Call
- Executive Right of Way
- Call Hold
- Call Back
- Call...

CHAPTER 3 NDA-24219  
Page 126
Revision 2.0
NAP-200-012
Sheet 1/1
Cleaning and Visual Check
1. CLEANING
Clean the following places:
• Inside of the main equipment, especially the bottom of the base.
•On the Top Cover.
• Around the Main Equipment and the MDF.
• Keyboard on the Attendant Console.
2. VISUAL CHECK
(1) Check to see if all circuit cards are in their positions correctly.
(2) Check that the cable connections in the PIM are correctly and completely connected, and the routing of the
cables has...