NEC Neax 1000 Ivs Very Small Platform System Manual

 NDA-24219 CHAPTER 3
Page 127
Revision 2.0
NAP-200-013
Sheet 1/1
Mounting of Front Cover
1. MOUNTING FRONT COVER
Mount the Front Cover onto PIM using the provided screws as shown in Figure 013-1.
Figure 013-1  Mounting Front Cover
PIM
FRONT FRONT COVER 

CHAPTER 3 NDA-24219  
Page 128
Revision 2.0
This page is for your notes. 

 NDA-24219   CHAPTER 4
CHAPTER 4  OFFICE  DATA P ROGRAMMING 

CHAPTER 4 NDA-24219  
Page 130
Revision 2.0
1.2.2 Station Data
In this table, the following data are required.
• Station Number: Station numbers (up to four digits), specified in the Numbering Plan Table, are assigned.
For the Multiline Terminal station, specify the Primary Extension Number.
• Type of Telephone
The type of station telephone set is specified as shown below.
TYPE OF TEL  DESCRIPTION 
DP................................... Dial Pulse Telephone set
PB ................................... DTMF...

 NDA-24219 CHAPTER 4
Page 131
Revision 2.0
• NUMBER OF LINE
Specify the number of trunks to be provided with each route (IC-Incoming, OG-Outgoing, BW-Bothway).
• DP/PB
Specify the type of address signal from/to distant office, as shown below.
TYPE OF TEL DESCRIPTION 
DP................................... Dial Pulse 
PB ................................... DTMF Signal
• KIND OF SIGNAL
Specify the kind of signaling system such as Ring Down, Loop, E & M etc. at the line.
1.2.4 Station Hunting Group Data
This...

CHAPTER 4 NDA-24219  
Page 132
Revision 2.0
1.2.6 Speed Calling-System Data
This data table requires the abbreviated code and the stored number to be sent out. A maximum stored number of 28
digits can be assigned.
1.2.7 Port Assignment Table
Specify the station number or trunk number corresponding to the LEN (Line Equipment Number) as shown in Table
4-2. The LEN means physical location number within the PIM.
Table 4-2  Port Assignment Method
CARD TO BE 
ASSIGNEDPORT ASSIGNMENT TABLE REMARKS
PN-8LC...

 NDA-24219 CHAPTER 4
Page 133
Revision 2.0
PN-AUC
PN-2DLC• Station number must be assigned to 1st LEN 
(LEVEL 0) and/or 2nd LEN (LEVEL 1) of each LT 
slot.
• For PN-2DLC, specify primary extension numbers 
of multiline terminal as follows:
PN-4COT
PN-4DIT• Trunk number must be assigned to 1st LEN 
(LEVEL 0) through 4th LEN (LEVEL 3) of each 
LT  s l o t .
PN-AUC
PN-2ODT• Trunk number must be assigned to 1st LEN 
(LEVEL 0) and/or 2nd LEN (LEVEL 1) of each LT 
slot. Table 4-2  Port Assignment Method...

CHAPTER 4 NDA-24219  
Page 134
Revision 2.0
PN-2DAT • Card number must be assigned to 1st LEN (LEVEL 
0) and/or 3rd LEN (LEVEL 2) of each LT slot.
PN-8RST • Card number must be assigned to 1st LEN (LEVEL 
0) and/or 3rd LEN (LEVEL 2) of each LT slot.
Note:When using the internal DTMF Receiver on
the MP card, assign Card No. E200 to LEN
No. 0124.
PN-DK00 • Card number must be assigned to 1st LEN (LEVEL 
0) and/or 3rd LEN (LEVEL 2) of each LT slot.
• Card numbers of External Equipment Interface are...

 NDA-24219 CHAPTER 4
Page 135
Revision 2.0
PN-CFT• Card number must be assigned to 1st LEN (LEVEL 
0) of each LT slot.
PN-2DPC • To assign data station number to PN-2DPC by 
CM1A, specify primary extension number of 
multiline terminal as a dummy station number.
• Primary extension number must be assigned to 1st 
LEN (LEVEL 0) and/or 3rd LEN (LEVEL 2) of 
each LT slot.
PN-TNT • Card number must be assigned to 1st LEN (LEVEL 
0) and/or 3rd LEN (LEVEL 2) of each LT slot. Table 4-2  Port Assignment Method...

CHAPTER 4 NDA-24219  
Page 136
Revision 2.0
PN-2AMP • Card number must be assigned to the 1st LEN 
(LEVEL 0) and/or 3rd LEN (LEVEL 2) of each LT 
slot.
PN-2ILC • ISDN circuit station number must be assigned to 
1st LEN (LEVEL 0) and/or 2nd LEN (LEVEL 1) of 
each LT slot. Table 4-2  Port Assignment Method (Continued)
CARD TO BE 
ASSIGNEDPORT ASSIGNMENT TABLE REMARKS
LEVEL 3
LEVEL 2
LEVEL 1
LEVEL 0
Not to be
LEVEL 7
LEVEL 6
LEVEL 5
LEVEL 4LT00
–
0007
–
0006
–
0005
–
0004
–
0003
C101
0002
–
0001
C100
0000...