NEC Mcu 5000a Multipoint Control Unit Equipment Manual

NECA 340-414-220 Revision 2.0 Page 1 of 2
MCU 5000A Multipoint Control Unit SPR-118
VIDEO MODE SETTING
TERMINAL MODE RELATED
SUMMARY:
Specify whether video mode is set or not.
STEP PROCEDURE 
Note:
Use the factory shipment value (08H 00H
) in setting the video mode as a general rule.  If 
change is necessary for any reason, follow the steps described below.
1 Enter the following command.
SSPR__ n1 =  x1 __n2 = x2 __ … ni = xi … ¿
ni:
System parameter addressA: 238H and 239H
B: 298H and 299H
[1] Addresses...

Page 2 of 2 NECA 340-414-220 Revision 2.0
SPR-118 MCU 5000A Multipoint Control Unit
VIDEO MODE SETTING
TERMINAL MODE RELATED
STEP PROCEDURE 
2 Verify that the normal response is displayed with “OK
”.
If YES
, go to Step 3
.
If NO
, go to Step 1
.
3 End of procedure. 

NECA 340-414-220 Revision 2.0 Page 1 of 2
MCU 5000A Multipoint Control Unit SPR-119
LSD MODE SETTING
TERMINAL MODE RELATED
LSD Mode (A: +23AH ~ 23BH) (B: +29AH ~ +29BH)
b7
b6b5
b4 b3 b2 b1 b0
b2 : 1200 bps
b3 : 4800 bpsDefault = 00H A: +23AH
00
0 fixed0000 fixed
0 fixed
b4 : 6400 bps
b6 : 9600 bps B: +29AH
b7 : 14,400 bps
Note:  When distributing LSD date, b7, b6, b4, b3 or b2 will be 1.
b7
b6b5
b4 b3 b2 b1 b0
Default = 00H 0 fixed0 fixed
0 fixed0 fixed 0 fixed
0 fixed
0 fixed0 fixed A: +23BH
B: +29BH 

Page 2 of 2 NECA 340-414-220 Revision 2.0
SPR-119 MCU 5000A Multipoint Control Unit
This page is for your notes. 

NECA 340-414-220 Revision 2.0 Page 1 of 2
MCU 5000A Multipoint Control Unit SPR-120
HSD CAPABILITY SETTING
TERMINAL MODE RELATED
HSD Capability (A: +23CH ~ 23FH) (B: +29CH ~ +29FH)
b7
b6b5
b4 b3 b2 b1 b0
Default = 00H 0 fixed0 fixed
0 fixed0 fixed 0 fixed
0 fixed
0 fixed0 fixed A: +23CH
B: +29CH
b7
b6b5
b4 b3 b2 b1 b0
Default = 00H 0 fixed000
0
0 A: +23DH
B: +29DH
b1 : 64 kbps
b2 : 128 kbps
b3 : 192 kbps
b4 : 256 kbps
b6 : 384 kbps
Note:  When distributing HSD date, bit will be 1.0 fixed
b7
b6b5
b4 b3 b2...

Page 2 of 2 NECA 340-414-220 Revision 2.0
SPR-120 MCU 5000A Multipoint Control Unit
This page is for your notes. 

NECA 340-414-220 Revision 2.0 Page 1 of 2
MCU 5000A Multipoint Control Unit SPR-121
MLP MODE SETTING
TERMINAL MODE RELATED
MLP Mode (A: +240H ~ 241H) (B: +2A0H ~ +2A1H)
Note:
  MCU 5000A does not support MLP, when RCON mode.
b7
b6b5
b4 b3 b2 b1 b0
Default = 00H 0 fixed0 fixed
0 fixed0 fixed 0 fixed
0
00 fixed A: +240H
B: +2A0H
b1 : MLP-4k
b2 : MLP-6.4k
b7
b6b5
b4 b3 b2 b1 b0
Default = 00H 0 fixed0 fixed
0 fixed0 fixed 0 fixed
0 fixed
0 fixed0 fixed A: +241H
B: +2A1H 

Page 2 of 2 NECA 340-414-220 Revision 2.0
SPR-121 MCU 5000A Multipoint Control Unit
This page is for your notes. 

NECA 340-414-220 Revision 2.0 Page 1 of 2
MCU 5000A Multipoint Control Unit SPR-122
NETWORK CLASSIFICATION MODE SETTING
TERMINAL MODE RELATED
Network Classification Mode (A: +242H ~ 243H) (B: +2A2H ~ +2A3H)
b7
b6b5
b4 b3 b2 b1 b0
Default = 01H 0 fixed0 fixed
0 fixed0 fixed 0 fixed
00 fixed A: +242H
B: +2A2H
b0 : 64 kbps (unrestricted)
b1 : 56 kbps (restricted) 0 fixed
b7
b6b5
b4 b3 b2 b1 b0
Default = 00H 0 fixed0 fixed
0 fixed0 fixed 0 fixed
0 fixed
0 fixed0 fixed A: +243H
B: +2A3H 

Page 2 of 2 NECA 340-414-220 Revision 2.0
SPR-122 MCU 5000A Multipoint Control Unit
This page is for your notes.