NEC Is15-2k Digital Cinema Projector User Manual

page 4.9
iS15-2K Cinema Projector: User Manual 4. Controlling the projector
Notes
Direct Menu selection:
1 Press the 
HELP Direct Menu
selection button.
2 Use the Alpha-numeric keys
to enter the menu number,
including any leading zeroes,
eg 005.
3 Press Enter.
Source Select menus 

page 4.10
4. Controlling the projectoriS15-2K Cinema Projector: User Manual
Notes
Direct Menu selection:
1 Press the 
HELP Direct Menu
selection button.
2 Use the Alpha-numeric keys
to enter the menu number,
including any leading zeroes,
eg 005.
3 Press Enter.
page 11
page 11
Configuration menus 

page 4.11
iS15-2K Cinema Projector: User Manual 4. Controlling the projector
Notes
Direct Menu selection:
1 Press the 
HELP Direct Menu
selection button.
2 Use the Alpha-numeric keys
to enter the menu number,
including any leading zeroes,
eg 005.
3 Press Enter.
page 10
page 10
Configuration menus
continued 

page 4.12
4. Controlling the projectoriS15-2K Cinema Projector: User Manual
page 13
page 13
Title Setup menus 

page 4.13
iS15-2K Cinema Projector: User Manual 4. Controlling the projector
Notes
Direct Menu selection:
1 Press the 
HELP Direct Menu
selection button.
2 Use the Alpha-numeric keys
to enter the menu number,
including any leading zeroes,
eg 005.
3 Press Enter.
page 12
page 12
Title Setup menus
continued 

page 4.14
4. Controlling the projectoriS15-2K Cinema Projector: User Manual
Notes
Direct Menu selection:
1 Press the 
HELP Direct Menu
selection button.
2 Use the Alpha-numeric keys
to enter the menu number,
including any leading zeroes,
eg 005.
3 Press Enter.
Warranted lamp life is
determined by the reading on
the Lamp-hours meter on the
face of the Lamp module -
NOT the reading available via
the Lamp menu shown here.
Information menus 

5. Maintenance
Contents
5. Maintenance5.1
Changing the air filter material .............................................................................................. 5.2
Changing the lamp .................................................................................................................. 5.4
Lamp-hours meter........................................................................................................................................... 5.4
Cleaning the projector and lens...

page 5.2
5. MaintenanceiS15-2K Cinema Projector: User Manual
Changing the air filter material
To change the filter:
Switch the projector into Standby mode, by pressing the POWER button on the
control panel or the POWER OFF button on the remote control for two seconds.
• The ON/STANDBY indicator on the control panel will change to orange, and
flash on and off.
The display will show the Cooldown timer, which will count down from
300 seconds to zero. At the end of the cooling period, the projector will go...

page 5.3
iS15-2K Cinema Projector: User Manual 5. Maintenance
• Replenish the filter, taking care to fit the new material correctly, as shown below:
- the cut edge of the wire lattice must be against the sealing strip,
- the wire lattice must face downwards,
- the first pleat of material must overhang the strap-end of the frame.
• Re-assemble the frame:
- Hook the bottom end on first.
- Re-fasten the two screws at the strap end.
• Push the replenished filter firmly back into the slot, taking care to fit...

page 5.4
5. MaintenanceiS15-2K Cinema Projector: User Manual
Changing the lamp
The lamp should be changed, by certified service personnel, after 750 hours of use,
as indicated on the lamp-hours meter. The meter is located on the front of the lamp
module, and is accesible inside the lamp compartment door.
Lamp-hours meter
Notes
The lamp should be changed
ONLY by certified service
personnel.
Always allow the lamp to cool
for 5 minutes before
removing the lamp module.
Do NOT open the lamp
compartment door...