NEC Is15-2k Digital Cinema Projector User Manual

page 2.25
iS15-2K Cinema Projector: User Manual 2. Installation
Signal inputsNotes
For more information about
input connections see the
following pages, and also
Connections, in section 6.
Appendix.
For more information about
supported input  formats  see
Specification, in section 6.
Appendix.
For more information about
control input connections see
the following pages, and also
Connections, in section 6.
Appendix.
For more information about
controlling the projector from a
computer, see your provider....

page 2.26
2. InstallationiS15-2K Cinema Projector: User Manual
Cinema Inputs (SMPTE 292 / HD-SDI)
For cinema use, this will be the main input port for the projector. The two inputs can
be configured as follows:
•  one dual SMPTE 292 port
•  two separate, individually selectable single SMPTE 292 ports.
The following source formats will be recognised and decoded by the projector
electronics:
•  SMPTE 274M
•  SMPTE RP211
•  SMPTE 295M
•  SMPTE 260M
•  SMPTE 296M
HDSDI is a 1.4Gb link, therefore the...

page 2.27
iS15-2K Cinema Projector: User Manual 2. Installation
DVI-D Inputs
The projector can also accept signals from a variety of alternative sources, via the
two DVI-D inputs.  An external image processing unit can be located close to source
equipment such as computers, video tape players and DVD players etc.  Therefore,
only the projector needs to be located in the projection booth.
The two inputs can be configured for use as:
• two separate, individually selectable Single DVI-D inputs
• one Twin...

page 2.28
2. InstallationiS15-2K Cinema Projector: User Manual
Control connections
LAN 1 and LAN 2
The projector can be controlled from a computer via a LAN connection, using a
standard ethernet cable (not supplied).
Interlocks
I/L is a pair of relay contacts, which are normally closed, but are open under the
following conditions:
•  lamp door open
• insufficient air flow
• over-temperature
• other internal fault (see LCD screen for error message)
The I/L contacts can be used for remote monitoring of the...

page 2.29
iS15-2K Cinema Projector: User Manual 2. Installation
USB
USB Type A is reserved for future expansion.
USB type B can be used to connect to a computer, using a standard USB cable.
Remote Control 1
Connect the Remote Control (supplied) to this socket.
Remote Control 2
An external switching unit (not supplied) can be connected to this socket.
PC Control
The projector can be controlled from a computer via a serial connection, using a
standard RS232 cable (not supplied).
PC Control T
Service or...

page 2.30
2. InstallationiS15-2K Cinema Projector: User Manual
Power connections
USA power input
Make sure the main power switch is off before connecting the power cable.
Firmly push in the Hubbell connector, then turn clockwise to lock.
Rest of World power input
Make sure the main power switch is off before connecting.
Lift the lid of the C-form connector then firmly push in the connector.
Notes
Use only the power cable
provided.
Ensure that the power outlet
includes a Ground
connection, as this...

3. Getting started
Contents
3. Getting started 3.1
Switching the power on .......................................................................................................... 3.2
Selecting a title ........................................................................................................................ 3.3
Displaying a test pattern......................................................................................................... 3.4
Adjusting the projected image...

page 3.2
3. Getting startediS15-2K Cinema Projector: User Manual
Switching the power on
• Connect the power cable between the mains supply and the projector.
• Push the main power switch upwards to switch on the power.
• The projector will initially be in Standby mode. The ON/STANDBY indicator on
the control panel will show orange, and the LCD screen will show Standby:
• To switch the projector ON from Standby mode, press the POWER button on
the control panel or the POWER ON button on the remote control...

page 3.3
iS15-2K Cinema Projector: User Manual 3. Getting started
Notes
For more detailed information
about how to use the control
panel and the remote control,
see the next section:
Controlling the projector.
Selecting a title
• Press the  MENU button on the control panel or on the remote control.
• Press the SELECT 
  or SELECT  buttons until Source Select is displayed, as
shown below:
• Press the SELECT 
 button, to see the first available title.
• Press the SELECT 
  or SELECT  buttons until the LCD...

page 3.4
3. Getting startediS15-2K Cinema Projector: User Manual
Notes
For more detailed information
about how to use the control
panel and the remote control,
see the next section:
Controlling the projector.
Displaying a test patter n
EITHER
• Use the Source Select menu as described on the previous page:
• Press the SELECT 
  or SELECT  buttons until Test Pattern is displayed, as
shown below:
• Press the SELECT 
 button or the ENTER button to select the Test Pattern
menu.
OR
• Press the  TEST button on...