NEC Is15-2k Digital Cinema Projector User Manual
Have a look at the manual NEC Is15-2k Digital Cinema Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
page 4.9 iS15-2K Cinema Projector: User Manual 4. Controlling the projector Notes Direct Menu selection: 1 Press the HELP Direct Menu selection button. 2 Use the Alpha-numeric keys to enter the menu number, including any leading zeroes, eg 005. 3 Press Enter. Source Select menus
page 4.10 4. Controlling the projectoriS15-2K Cinema Projector: User Manual Notes Direct Menu selection: 1 Press the HELP Direct Menu selection button. 2 Use the Alpha-numeric keys to enter the menu number, including any leading zeroes, eg 005. 3 Press Enter. page 11 page 11 Configuration menus
page 4.11 iS15-2K Cinema Projector: User Manual 4. Controlling the projector Notes Direct Menu selection: 1 Press the HELP Direct Menu selection button. 2 Use the Alpha-numeric keys to enter the menu number, including any leading zeroes, eg 005. 3 Press Enter. page 10 page 10 Configuration menus continued
page 4.12 4. Controlling the projectoriS15-2K Cinema Projector: User Manual page 13 page 13 Title Setup menus
page 4.13 iS15-2K Cinema Projector: User Manual 4. Controlling the projector Notes Direct Menu selection: 1 Press the HELP Direct Menu selection button. 2 Use the Alpha-numeric keys to enter the menu number, including any leading zeroes, eg 005. 3 Press Enter. page 12 page 12 Title Setup menus continued
page 4.14 4. Controlling the projectoriS15-2K Cinema Projector: User Manual Notes Direct Menu selection: 1 Press the HELP Direct Menu selection button. 2 Use the Alpha-numeric keys to enter the menu number, including any leading zeroes, eg 005. 3 Press Enter. Warranted lamp life is determined by the reading on the Lamp-hours meter on the face of the Lamp module - NOT the reading available via the Lamp menu shown here. Information menus
5. Maintenance Contents 5. Maintenance5.1 Changing the air filter material .............................................................................................. 5.2 Changing the lamp .................................................................................................................. 5.4 Lamp-hours meter........................................................................................................................................... 5.4 Cleaning the projector and lens ............................................................................................. 5.5
page 5.2 5. MaintenanceiS15-2K Cinema Projector: User Manual Changing the air filter material To change the filter: Switch the projector into Standby mode, by pressing the POWER button on the control panel or the POWER OFF button on the remote control for two seconds. • The ON/STANDBY indicator on the control panel will change to orange, and flash on and off. The display will show the Cooldown timer, which will count down from 300 seconds to zero. At the end of the cooling period, the projector will go into Standby mode. • Push the main power switch downwards to switch off the power. • Pull the filter out from under the front of the projector, under the lens, by pulling on the strap. • Inspect the foam sealing strips at the ends and sides of the filter. If they are damaged, then the whole filter should be replaced. • Dismantle the filter: - Remove the two screws securing the strap-end of the frame. - HInge up the top of the frame and unhook from the bottom end. - Remove the filter material. Notes The projector must be switched OFF before removing the air filter, otherwise dust could be sucked into the projector by the ventilation fan. The filter material should be changed regularly: • In a clean environment such as a projection room, change after 750 hours, at the same time as the lamp is changed. • In a dusty or smoky environment such as a theatre or public area, more frequent changes may be necessary.
page 5.3 iS15-2K Cinema Projector: User Manual 5. Maintenance • Replenish the filter, taking care to fit the new material correctly, as shown below: - the cut edge of the wire lattice must be against the sealing strip, - the wire lattice must face downwards, - the first pleat of material must overhang the strap-end of the frame. • Re-assemble the frame: - Hook the bottom end on first. - Re-fasten the two screws at the strap end. • Push the replenished filter firmly back into the slot, taking care to fit it the right way up, as shown by the arrow.Notes
page 5.4 5. MaintenanceiS15-2K Cinema Projector: User Manual Changing the lamp The lamp should be changed, by certified service personnel, after 750 hours of use, as indicated on the lamp-hours meter. The meter is located on the front of the lamp module, and is accesible inside the lamp compartment door. Lamp-hours meter Notes The lamp should be changed ONLY by certified service personnel. Always allow the lamp to cool for 5 minutes before removing the lamp module. Do NOT open the lamp compartment door whilst a film is being shown - safety interlocks on the door will shut down the projector without warning. Do not use the lamp for more than 750 hours, as this may cause serious lamp failure, damage the lamp module and cause extra cost on replacement. Warranted lamp life is determined by the reading on the Lamp-hours meter on the face of the Lamp module, shown here - NOT the reading available via the Information menus. There are no user-serviceable parts inside the lamp module. The whole module should be replaced and returned to your provider for re-furbishment. Xenon lamps produce high intensity light. Do not look directly at the light coming from the lamp housing or the lens. LCD meter display button The Lamp-hours meter has two modes of operation: • When the projector is running, the LCD will show lamp run hours. • When the projector is in Standby mode, the LCD will be blank. To display lamp run hours press the button and hold for 5 seconds.