NEC Infoset 408 System Manual

InfoSet 408Issue 1A
System Manual6 - 25
361Ringing Cycle for Trunk Line 
1


  ! 

Assigns the ringing cycle for each 
telephone.  If a number in the Caller 
ID display matches a number 
stored in system speed dialing, the 
system will use the same ringing 
cycle that system speed dialing 
uses.
Refer to Appendix B Tone Patterns 
for the ringing cycles.
0 = Cycle A
1 = Cycle B
2 = Cycle C
3 = Cycle D
362Ringing Cycle for Trunk Line 
2


  ! 

363
Ringing Cycle for...

Issue 1AInfoSet 408
6 - 26Telephone Programming
403Tenant-to-Telephone 
Assignment

 



Used to assign each telephone to a 
tenant.  Both multiline and single 
line telephones can be assigned to 
a tenant.1~10 = Assigned to Tenant 1 
– = Assigned to Tenant 2
Programming Note:For Function 403, the telephone ports are displayed in descending order 
(0987654321).  To change the default values, press the dialpad key that 
corresponds to the port you want to change. For example, to change...

InfoSet 408Issue 1A
System Manual6 - 27
504Single Line Telephone 
Hookflash End Time

   

End time indicates the maximum 
time that passes before the system 
recognizes the flash as a valid 
hookflash.  If the flash is longer 
than the time set, the system 
considers the flash as a disconnect 
signal.
To determine the duration of the 
hookflash signal, the system 
computes using the following 
formula:  SLT Hookflash Start Time 
+ SLT Hookflash End Time = SLT 
Duration.
End time is used in...

System Manual7 - 1
PC Programming
 
SECTION  1 INTRODUCTION
The PC Programming software allows users to program all of the features and
functions of the InfoSet key telephone system.  PC Programming is a menu-based
program that provides programming for basic and advanced users.  PC Programming
uses .html files and is viewed using an internet browser.  A wizard is provided to help
“walk” users through the programming of the features of the system.  The Expert
button provides access to advanced...

Issue 1AInfoSet 408
7 - 2PC Programming
SECTION 3INSTALLING PC PROGRAMMING SOFTWARE
To install the software:
1. Insert the setup CD in the CD ROM drive.
2. Click the Windows 95/98 
Start button.
3. Select 
Run.
4. Enter 
d:\setup.exe and click OK.
(D = the letter of the CD ROM drive.
5. Follow the installation instructions.  
SECTION 4STARTING PC PROGRAMMING
After the PC Programming software has been installed and the appropriate
modifications have been made to the internet browser, the program can be...

In fo S et  40 8  Issue  1A
S yst em  Man ual  7 - 3
Figure 7- 1  Na vig at io nal  B ars  fo r  In te rnet Br owse rs
Microsoft Explo rer  Navigational  Bar 

Issue 1AInfoSet 408
7 - 4PC Programming
  
Table 7-1  Quick Guide to InfoSet Programming Menus
Tool Bar Icons
Icon Definition Icon Definition
Sets up outside lines, telephones, 
and extension numbers.Produces a switch report.
Sets up line keys, one-touch keys, 
and speed dials.Provides on-line help.
Sets up telephone ringing 
assignments.Connects to the Key Telephone 
System (KTS).
Sets up telephone dial restrictions.Uploads data to the Telephone 
System (KTS).
Creates a new configuration.Downloads data...

In fo S et  40 8  Issue  1 A
S yst em  Manu al  7 - 5 

Issue 1AInfoSet 408
7 - 6PC Programming
6.2 Switch Menu
The Switch screen can be accessed by clicking on the Switch icon from the
toolbar on the main menu.  If this is the first time you are programming the
system, this is the first screen to program.  
This screen is used to define the hardware configuration of the InfoSet
system.  Use this screen to assign the number of outside lines attached to
the system.  When an outside line is assigned it appears yellow on the
screen.  For each telephone a unique...

InfoSet 408Issue 1A
System Manual7 - 7

 	
	
Te l
This option indicates which telephone is being programmed. This field is
for informational purposes only and cannot be changed by the user.
Extension Number
This option indicates the extension number (10~59) assigned to each
telephone in the system.  The extension number must be unique for each
telephone; you cannot assign duplicate extension numbers.
Telephone Type
This pull down menu allows users to select the telephone type.   Valid...