NEC Gt950 Lcd Projector Users Manual

E – 11
SOURCE
SELECT
LENS SHIFT
FOCUSZOOM STATUS
POWER
ON/STAND BY AUTO
ADJUST
MENU
ENTER
CANCEL
8
10
9 7 6 12 111 3
2
54
1. Power Button (ON / STAND BY)
Use this button to turn the power on and off when the power is sup-
plied and the projector is in standby mode.
NOTE: To turn off the projector, press and hold this button for a minimum oftwo seconds.
2. Auto Adjust Button
Use this button to adjust an RGB or DVI (digital/analog) source for an
optimal picture. Some signals may not be displayed correctly...

E – 12
Terminal Panel Features
1. DVI-I Input Connector (DVI 29 pin)
This connector can be used to accept digital or analog signal output
from a computer with a DVI connector.
2. RGB Input Connector (Mini D-Sub 15 pin)
Connect your PC or other RGB equipment. Use the signal cable that's
supplied to connect to a PC.
3. RGB Output Connector (Mini D-Sub 15 pin)
You can use this connector to loop your computer image to an external
monitor from the RGB input source.
DVI digital signal will not be output....

E – 13
17. PC Card Slot
Insert a PC card here.
18. PC Card Eject Button
Press to eject a PC card.
19. PC Card Access Indicator
Lights while accessing a PC card. 13. S-VIDEO Audio Input Jacks (RCA)
L/MONO
This is your left channel audio input for stereo sound coming from the
S-VIDEO source.
This also serves as your monaural audio input.
R
This is your right channel audio input for stereo sound from the S-
VIDEO source.
14. Audio Output Jacks (RCA)
You can use this connector to output sound from the...

E – 14
4. LED
Flashes when any button is pressed.
5. Power ON Button
If the main power is applied, you can use this button to turn your pro-
jector on.
6. Power OFF Button
If the main power is applied, you can use this button to turn your pro-
jector off.
NOTE: To turn off the projector, press and hold the POWER OFF button for aminimum of two seconds.
7. VIDEO Button
Press this button to select an NTSC, PAL, SECAM or NTSC4.43 com-
patible video source from a VCR, DVD player, laser disc player or docu-...

E – 15
PJ
FOCUS ZOOM
VOLUME
SHIFT
HELP
POINTER
KEYSTONEMAGNIFY
FREEZE
PIC-MUTEPC CARDSLIDE
FOLDER
SLIDE
LIST
17
19
20
28
29
30
31 22
18
21
23
24
25
26
27
17. PJ Button
Press this button to switch the Select, Cancel, and Enter buttons be-
tween the Projector mode (lit red) and the Computer mode. Press this
button or any one of the Power ON/OFF, Menu, Focus, Zoom, Shift,
Help, Pointer, Magnify, PC Card, Folder List or Slide List buttons to
switch to the Projector mode and the PJ button lights red. To...

E – 16
Operating Range Remote Control Battery Installation
1. Press firmly and slide the battery cover off.
2. Remove both old batteries and install new ones (AA). Ensure that
you have the batteries polarity (+/–) aligned correctly.
3. Slip the cover back over the batteries until it snaps into place.
Do not mix different types of batteries or new and old batteries.
Remote Control Precautions
•Handle the remote control carefully.
•If the remote control gets wet, wipe it dry immediately.
•Avoid excessive...

E – 17
Switching operation mode between computer and projector
The three shaded buttons shown on the drawing work as a computer mouse in the Computer mode.
In the Computer mode the PJ button is not lit.
•When the MENU button is pressed, the PJ button lights red to indicate that you are in the Projector mode, which allows the projector menu
operation using the three buttons.
•When the POINTER button is pressed, the PJ button lights red to indicate that you are in the Projector mode and that the SELECT 
...

E – 18 Ceiling Installation
Distance Chart
Standard Lens (H
2.0) – (H
2.4)
Long Zoom Lens (H
3.4) – (H
5.1)
174.9 mm (7”)
2. INSTALLATION
This section describes how to set up your GT950 projector and how to
connect video and audio sources.
Setting up Your Projector
Your GT950 Projector is simple to set up and use. But before you get
started, you must first:
1. Determine the image size.
2. Set up a screen or select a non-glossy white wall onto which you
can project your image.
3. Connect the supplied...

E – 19
WARNING
•Installing your projector on the ceiling must be done by a quali-
fied technician. Contact your NEC dealer for more information.
* Do not attempt to install the projector yourself.
•Only use your projector on a solid, level surface. If the projector
falls to the ground, you can be injured and the projector se-
verely damaged.
•Do not use the projector where temperatures vary greatly. The
projector must be used at temperatures between 32˚F (0˚C)
and 95˚F (35˚C).
•Do not expose the...

E – 20
Lens Shift Adjustable Range
SOURCERIGHT LEFTSELECTLENS SHIFTFOCUSUP
DOWNZOOM STATUS
POWER
ON/STAND BY AUTO
ADJUSTMENUENTERCANCEL
Desktop/Front
Vertical
Ceiling/Front
Vertical
Normal position
Normal position
Normal position
Horizontal0.85V
0.85V
0.55HMaximum Possible Range:
Up: 0.85 V
Down: 0.85 V
Right: 0.55 H
Left: 0.55 H
(H: width of projected image, V: height of projected image)
NOTE: If lens is shifted in two directions combined, maximum range in either
direction cannot be obtained due to...