NEC Applications Manager Installation Manual

NDA-30025   Revision 4.0Page 45
APM System Installation Manual APPLICATION MANAGER INSTALLATION
14. If the installation uses TCP/IP as its OAI link, the TCP/IP services for APM 
must be configured. To configure the TCP/IP, type y and press Enter at the“Will 
this installation be using TCP/IP to communicate with the PBX” prompt, and 
type y and press Enter at the “Do you want to install the TCP/IP Services for 
the APM Platform now” prompt.
The TCP/IP Addressing menu displays:
15. The default IP address...

Page 46NDA-30025   Revision 4.0
APPLICATION MANAGER INSTALLATION APM System Installation Manual
18. Type the host name of the PBX and press Enter.
19. Type the PBX TCP/IP address and press Enter.
20. If the host name and TCP/IP address are correct, type y and press Enter.
The menu redisplays.
21. Type s and press Enter to save the PBX address and exit.
The following screen appears:
22. The IP addresses will be updated in the /etc/hosts file. After the installation has 
completed, the OAI links must be...

NDA-30025   Revision 4.0Page 47
APM System Installation Manual APPLICATION MANAGER INSTALLATION
25. Press Enter to continue.
Modifications made to the UNIX operating system will require the operating 
system to relink. The UNIX operating system will relink and create a new 
operating system.
26. At this point in the installation, a new UNIX operating system is recreated. Type 
y and press Enter at the “Do you want this kernel to boot by default?” prompt. 
This kernel will be the default when the system...

Page 48NDA-30025   Revision 4.0
APPLICATION MANAGER INSTALLATION APM System Installation Manual
28. After the new UNIX operating system has been created, it is necessary to reboot 
the system and load the new UNIX operating system. Press Enter to shut down 
the operating system.
The installation will continue the shut down until the following screen appears:
29.  To reboot the system press Enter.
After the system has rebooted and enters multi-user mode, the Application 
Platform Manager login displays,...

NDA-30025   Revision 4.0Page 49
APM System Installation Manual BACKUP AND RESTORATION PROCEDURES
Chapter 5 BACKUP AND RESTORATION PROCEDURES
Creating Boot and Root Floppy Disks
SCO recommends the creation of an Emergency Boot Floppy set after installation. 
This is the only means of attempting recovery of the root filesystem or the kernel 
in the event that problems occur. 
To create a boot and root floppy disks follow the procedure below:
1. At the “#” prompt, type mkdev fd and press Enter.
The...

Page 50NDA-30025   Revision 4.0
BACKUP AND RESTORATION PROCEDURES APM System Installation Manual
7. Insert a 135ds18 floppy disk into the disk drive, and press Enter.
8. At the “Would you like to format the floppy disk first? (y/n) prompt, type n and 
press Enter.
The filesystem floppy is created, and the menu reappears.
9. Exit the menu by typing q and pressing Enter.
Tape Backup and Restore
The UAP system must be backed up prior to making any changes to the system. 
This will ensure that the system can...

NDA-30025   Revision 4.0Page 51
APM System Installation Manual BACKUP AND RESTORATION PROCEDURES
5. After you have recorded the information, exit the menu by typing q and pressing 
Enter.
The following screen displays:
6. Type e and press Enter.
The “#” prompt displays.
7. Type exit and press Enter.
Step 2: Boot the System from the Boot and Root Floppies
In order to backup the UAP, the system must be loaded from the boot and root 
floppies. If the system was loaded from the hard disk, it must be shut...

Page 52NDA-30025   Revision 4.0
BACKUP AND RESTORATION PROCEDURES APM System Installation Manual
3. To save the drive parameters, fdisk partition information and divvy information 
on the root floppy and hard drive so that they can be viewed during the recovery 
procedure. Run the following commands pressing Enter after each line:
(a) # dparam /dev/rhd00 > /dkinit.sav
(b) # dparam /dev/rhd00 > /mnt/dkinit.sav
(c) # fdisk -p > /fdisk.sav
(d) # fdisk -p > /mnt/fdisk.sav
(e) # divvy > /divvy.sav
q
e
(f) #...

NDA-30025   Revision 4.0Page 53
APM System Installation Manual BACKUP AND RESTORATION PROCEDURES
RestoreUse the following steps to restore the UAP:
Step 1: Boot the UAP from the Boot and Root Floppies
In order to restore the UAP, the system must be loaded from the boot and root 
floppies. If the system was loaded from the hard disk, it must be shut down so it 
can be loaded from the boot and root floppies. For information on booting from the 
boot and root floppies, see “Step 2: Boot the System from the...

Page 54NDA-30025   Revision 4.0
BACKUP AND RESTORATION PROCEDURES APM System Installation Manual
3. Type 1 and press Enter.
The drives parameters display. For a typical 1 Gigabyte hard drive, the 
parameter table would contain the following values: 
Disk Parameters Values
1. Cylinders 2047
2. Heads 16
3. Write Reduce 0
4. Write Precomp 0
5. Ecc 0
6. Control 8
7. Landing Zone 2048
8. Sectors/track 63
Note:
The number of cylinders, sectors, and heads varies from disk to disk. These may 
need to be modified...