Namco Race On Operators Manual

Page 31
3. MAJOR COMPONENTS 

Page 32
5. INSTALLATION
Notes on Installation 
WARNING •NEVER turn the power to the machine ON until 
installation has been completed.
WARNING • In order to prevent possible electric shocks, be sure that the machine is connected to the mains with a
securely connected earthed plug.
WARNING • So that customers are not injured , ensure that there is at least 500mm separation between other machines or
walls.
CAUTION • In  order to avoid damage to the machine due to mis-
operation, ensure that the voltage of...

Page 33
D
DENNE MASKINE ER KUN DESIGNET TIL INDENDØRSBRUG
INSTALLER IKKE MASKINEN PÅ FØLGENDE STEDER
1. Udendørs
2. Direkte sollys, steder med høj fugtighed el. støv, steder med vand udslip, i
nærheden af air-condition eller varme udstyr, steder med usædvanlig høj
el. kold temperatur.
3. Steder hvor den vil stå i vejen for nødudgange eller brandslukningsudstyr.
4. Ustabile steder eller steder med for store vibrationer.
5. Steder der ikke er plane.
ESTA MÁQUINA ESTA DISEÑADA ÚNICAMENTE PARA USO EN...

Page 34
K
I
N
O
DENNE MASKINEN ER BARE KONSTRUERT FOR INNENDØRS BRUK
IKKE INSTALLER MASKINEN PÅ FØLGENDE PLASSER.
1. Utendørs
2. Konstant sollys, plasser med mye fuktighet og støv, plasser hvor det er vannlekasje,
nære luft kjølere eller varme elementer, plasser med overdreven høy eller lav temperatur.
3. Plasser hvor det vill stå i veien for nødutganger eller brannslukking utstyr.
4. Ustabile plasser eller plasser med overdreven vibrasjon.
5. Plasser som ikke er i vater.
 DEZE MACHINE IS ALLEEN VOOR...

Page 35
l S
DENNA MASKIN ÄR AVSEDD ENBART FÖR INOMHUSBRUK
INSTALLERA EJ MASKINEN PÅ FÖLJANDE STÄLLEN
1. Utomhus
2. I direkt solsken, platser med extremt hög luftfuktighet eller damm, platser där det
förekommer vattenläckage, nära luftkonditionering eller värmeelement, i extremt hög
eller låg temperatur.
3. Platser där den skulle kunna vara i vägen för nödutgångar och
brandsläckningsutrustning.
4. Instabila ställen eller där stark vibration förekommer.
5. Platser med nivåskillnad.
TÄMÄ LAITE ON...

Page 36 5-2 Fitting the Header Assembly
The Header Assembly has a forward centre of gravity, so it is important that at
least 
two people are used to fit or remove the Header Assembly.
The fitting position of the Header Assembly is very high, and it is important
that a means of reaching the height safely , without stretching, is available
(e.g. steps, step stool etc.)
1. Place the Header Assembly on to the top of the Monitor Cabinet and
connect the connector.
2. Slide the Header Assembly forward, taking...

Page 37 5-3 Fitting the Seat Assemblies
1. Remove 10off security screw (M5x16) and remove both floor plates.
2. Place the Seat Assemblies up to the Monitor Cabinet and set the
adjustable feet so that the seat base is level with the main cabinet.
3. Connect the connectors.
4. Fit the 8off Hex head screws (M8x25), 4 screws per seat, with flat and
spring washers to retain the Seat Assemblies in position.
5. Refit the floor plates with the 10off security screws (M5x16). 

Page 38
5-4 Adjusting the Level Adjusters
1. When the assembled game is in its final position, lower the twelve (12)\
 level adjusters,(4off Monitor Assy and 4off each Seat Assy), with a 
spanner so that the machine is level and all castors are raised from the\
floor by approx. 5mm. Tighten the lock nuts with a spanner to ensure that
the level adjusters do not move.
Note: If the location site of this machine has a polished floor it is recommended\
that rubber pads are fitted under the level adjusters...

Page 39
2 Games Linked
3 Games Linked
4 Games LinkedZ 

Page 40
5-6 Linking Two or More Games
1. Remove 2off pozi head screws (M5x12) and remove the Link Cover Bracket.
2. Fit the Link Cable (supplied) as shown in the following diagram.
3. Refit the Link Cover Bracket with the 2off pozi head screws (M5x12). 
4 . See section 6-3-2 page  46 to set the game PCB ID.  Failure to set
the ID  will prevent the games operating correctl y.
Linking Two Games