Namco Motorcross Go Deluxe Operators Manual

Page 31
3. MAJOR COMPONENTS 

Page 32 

Page 33
4. MOVING THE MACHINE
This machine is fitted with castors to make it easier to move. Take care when 
moving the machine on an inclined surface.
The overall height of the machine is 2280mm. Take care of any overhead 
obstructions. (e.g. Light Fittings, Electric Cables etc.)
When moving the game, ensure that the game is dis-assembled into 3 parts\
: 
Monitor Assembly, Ride Assembly, and Header Assembly.
Note: The monitor assembly can be further dismantled by removing the pro\
jectorfrom the...

Page 34
G
DIESES GERÄT IST NUR FÜR DIE GEWERBLICHE AUFSTELLUNG IN
GESCHLOSSENEN RÄUMEN BESTIMMT.
DAS GERÄT DARF AN FOLGENDEN PLÄTZEN NICHT AUFGESTELLT WERDEN
1. Im Freien.
2. In direktem Sonnenschein, an extrem feuchten und staubigen Plätzen, an Plätzen mit
Wasseranschlüssen und möglichen Leckagen, nahe Klima- und Heizungsanlagen, an
Plätzen mit extrem hohen oder niedrigen Temperaturen.
3. In der Nähe von Notausgängen oder Feuerlöschgeräten.
4. An unstabilen Plätzen oder Plätzen mit übermäßiger...

Page 35
F
K
I
N
O
DENNE MASKINEN ER BARE KONSTRUERT FOR INNENDØRS BRUK
IKKE INSTALLER MASKINEN PÅ FØLGENDE PLASSER.
1. Utendørs
2. Konstant sollys, plasser med mye fuktighet og støv, plasser hvor det er vannlekasje,
nære luft kjølere eller varme elementer, plasser med overdreven høy eller lav temperatur.
3. Plasser hvor det vill stå i veien for nødutganger eller brannslukking utstyr.
4. Ustabile plasser eller plasser med overdreven vibrasjon.
5. Plasser som ikke er i vater.
 DEZE MACHINE IS ALLEEN VOOR...

Page 36
P
l S
ESTA MAQUINA FOI CONCEBIDA PARA UTILIZAÇÃO EM ESPACOS
INTERIORES APENAS
NÃO INSTALAR A MAQUINAS NOS SEGUINTES LOCAIS:-
1. Exteriores.
2. `Luz solar directa, locais com humidade excessiva ou pó, locais aonde existam fugas de
água perto de ar condicionados ou equipamentos calorificos e locais com temperaturas
excessivamente quentes ou frias.
3. Locais aonde ficaria colocada no caminho de saidas de emergência ou equipamentos
extintores de fogo.
4. Locais estruturalmente instaveis ou locais com...

Page 37
5-1 Removing the Monitor from the Monitor Base
The monitor is heavy (approx. 100kg). At least 4 people are required to lift the monitor from the monitor base.
1. Remove 6off Pozi head screws (M5x30), and remove the front cover panel.
2. Disconnect the connectors. 
3. Remove 2off Hex head screws (M10x130), spring and special washer from the front underside of the monitor. 

Page 38 4. Remove 2off Pozi head screws (M5x30) and remove the cover bracket.
5. Remove the rear door from the monitor base.
6. Remove 2 off Hex head screw (M10x130), spring and special washers
from the rear underside of the monitor.
7.  Carefully lift and remove the monitor from the base.
Note: Ensure that the monitor is kept level and avoid any knocks while lifting
or carrying the monitor. 

Page 39 5-2 Fitting the Header Assembly
The Header Assembly has a forward centre of gravity, so it is important
that at least 
two people are used to fit or remove the Header Assembly.
The fitting position of the Header Assembly is very high, and it is
important that a means of reaching the height safely, without stretching, is
available. (e.g. steps, step stools etc.)
1. Place the Header Assembly on top of the monitor cabinet and slide it
backwards so that the header base engages in the retainer...

Page 40 5-3 Fitting the Ride Base Assembly
1. Remove 4off Hex head screws (M8x30), flat and spring washers, and
remove the joint brackets from the base ride.
2. Place the Ride Base Assembly close to the monitor cabinet.
3. Connect the connectors and air tube between the Ride Base and the
monitor cabinet and push the Ride Base up to the monitor cabinet, taking
care not to trap the cable or connectors.
4. Fit the joint brackets to the Ride Base and Monitor Cabinet using the 4off
Hex head screws (M8x30).
5...