Namco Motorcross Go Deluxe Operators Manual

Page 51 6-3-4 Sound Test
1. Select “Sound Test” on the menu screen to set the sound volume levels.
The following screen is displayed.
2. Use the Select Up/Down switch to choose the required item then press
the Enter button.
3. Use the Select UP/Down switch to change the setting, the press Enter to
store the change.
4. Select “EXIT” and press the Enter button to return to the menu screen.
(a) Volume setting for left channel speaker. Settable from 0 ~ 65 with 0
quietest and 63 loudest.
(b) Volume setting...

Page 52 6-3-5 Monitor Test
1. Select “MONITOR TEST” on the menu screen to test and adjust the
Monitor. The following screen is displayed.
2. Use the Select Up/Down switch choose the required item then press the
Enter button. To return to the Monitor Test Menu from a test pattern press
the Enter button.
3. Select “EXIT” and press the Enter button to return to the menu screen.
Note:
Items (b) and (h) are not used on this game.
MONITOR TEST
GRADATION PATTERN..................................... (a)...

Page 53
6-3-7 Others
1. Select “OTHERS” on the menu screen. The following screen is displa\
yed. 
2. Use the Select Up/Down switch choose the required item then press the Enter button.
3. Select “EXIT” and press the Enter button to return to the menu scr\
een. 
(a,) Displays game software version. 
(b) Allows the internal clock and calender to be set.
(d), (e), (f) Used to test the PCB .
(g) When selected the Data Initialization Menu appears. To reset all game settings to factory setting and clear all...

Page 54
7. INITIALIZATION
Adjustments when Replacing Parts (Initialization) 
The following adjustments should always be performed after replacing the\
 
Game PC Board, ROM, or Control Potentiometers.
The game will not operate correctly if these adjustments are not made. 
1. Ensure that the Bike and Handlebar assemblies are in their central stand\
-by positions.
2. Slide the Test switch “ON” and select ‘BIKE INITIALIZATION’ from the menu screen  (See 6-3 page  45). The following screen will be displayed....

Page 55
8. REMOVING AND REPLACING ASSEMBLIES AND PARTS.
G GG G
GAdjustment or maintenance on this machine should be carried out by
qualified personnel only.
Do not make any alterations on this machine without prior approval.
Doing so could cause unforeseeable danger.
If performing work not described in this manual, be sure to contact
your distributor for instructions, as no responsibility will be
accepted for damage or injury
D DD D
DEinstellungen und Wartung des Gerätes dürfen nur von dafür...

Page 56
I II I
IRegolazioni e manutenzione su questa macchina devono essere fatti
solo da personale specializzato.
Non apporre alcuna modifica alla macchina senza autorizzazione
preventiva. Il fare questo può causare un pericolo non prevedibile.
Se state per iniziare un lavoro non descritto in questo manuale,
contattate il vostro distributore per instruzioni poichè non si accetta
alcuna responsabilità per danni o ferite.
N NN N
NJustering eller vedlikehold på denne maskinen skall bare utføres av...

Page 57
8-1 Compressor Assembly
NOTE:
There are no user serviceable parts on the compressor assembly.
Under no circumstances should any regulator valve be adjusted.
Altering the regulator valves could lead to serious damage.
8-2 Replacing the Bike Swing Potentiometer 1. Remove 4off Security screw (M5x12) and remove the front bearing cover. 
2. Disconnect the connector. 
3. Loosen the grub screw (M4x10) and remove the potentiometer complete with the mounting bracket.
4. Replace the potentiometer taking...

Page 58 8-3 Replacing the Throttle Potentiometer
1. Remove 6off Security screw (M5x10) and remove the Throttle Cover and
Cable Joint Plate.
2. Remove 2off Pozi head screws (M4x10), and remove the potentiometer
complete with bracket and gear.
3. Loosen the grub screw (M4x10) and remove the gear.
4. Replace the potentiometer taking care to connect the correct colour wire
to the correct terminal.
When replacing the potentiometer ensure that the locating tab engages in
the hole in the pot bracket. 

Page 59
5. Replace the gear and tighten the grub screw (M4x10).
When refitting the gear ensure that the grub screw engages on the flat o\
f
the potentiometer shaft and the rotational position of the pot shaft iscorrect. (see diagram below)
6. Refit the throttle cover and cable joint plate with 6off Security screw (M5x10).
Note: When engaging the grip base and the spur gear , the grub screw (M4x10)
of the spur gear should be positioned at the upper side (vertical) whe\
n the throttle is wide open.
Note:...

Page 60
8-4 Replacing the Brake Lever Potentiometer
1. Remove the Throttle Cover and Cable Joint Plate.  (see Section 8-3 (1)
page  58)
2. Loosen the grub screw (M3x5) and remove the potentiometer complete with bracket.
3. Replace the potentiometer taking care to connect the correct colour wire\
 to the correct terminal. 
When replacing the potentiometer ensure that the locating tab engages in\
the hole in the pot bracket and that the grub screw engages on the flat \
of
the potentiometer shaft.
4. Refit...