Namco Motorcross Go Deluxe Operators Manual

Page 41 6. Remove 4off security screw (M5x12), and remove the rear cover.
7. Remove the 2off Hex head screws (M8x30), and remove the two shipping
brackets.
There are two screw holes to enable the brackets to be stored for future
use. Use the M8x30 screws to retain the brackets.
8. Refit the rear cover and retain with the 4off security screws (M5x12).
9. Fit the bike number decals to the rear side of the bikes. 

Page 42
5-4 Linking Machines
Up to 4 games can be linked together for linked game play. To link games together, use the supplied link cable as described below.
1. Remove the pozi head screw (M5x10) and remove the link cover. (Located on the rear of the machine next to the mains-in connector.)
2. Fit the link cables as per the diagrams below. 
3. Refit the link covers and retain with the pozi head screw (M5x10) 
4. Ensure that the PCB in each game is set to the correct ID number. (See section 6-3-2 page...

Page 43
6. ADJUSTMENTS
6-1 Turning on the Power
After the machine has been installed, turn ON the power. The power
switch is located on the rear of the monitor cabinet.
G GG G
GAdjustment or maintenance on this machine should be carried out by
qualified personnel only.
D DD D
DEinstellungen und Wartung des Gerätes dürfen nur von dafür
qualifiziertem Fachpersonal vorgenommen werden.
l ll l
lJusteringer eller vedligehold af denne maskine bør kun udføres af
kvalificeret personale.
E EE E
ELos ajustes y el...

Page 44
6-2 Adjustment Switches
The Adjustment switches are located inside the coin door. 
1. Service Switch. Press this switch to obtain game credits without incrementing the play 
meter.
2. Test Switch Slide the test switch ON to enter test mode.
Test mode allows testing and the changing of game settings. (Refer to
section  6-3  Test Mode page  45)
3. Select Up/Down Switch This switch is used to select the test required when in the Test Mode.
4. Enter Switch This switch is used to enter a selected test...

Page 45 6-3 Test Mode
1. Open the coin door and slide the test switch “ON”. The “Menu Screen” will
be displayed on the monitor.
2. Select the test required by using the select up/down switch. The colour of
the selected test will change.
3. Activate the test by pressing the Enter switch. Select “EXIT” in each test
to return to the “Menu Screen”.
4. After testing is completed, slide the test switch to the “OFF” position to
return to normal game mode.
The Test Switch must always be in the “OFF” position for...

Page 46
6-3-1 Coin Options
1. Select “COIN OPTIONS” on the menu screen to set the game cost
and related settings. The following screen is displayed.
2. Use the Select Up/Down switch choose the required item then press
the Enter button.
3. Use the Enter button to change the setting.
4. Select “EXIT” and press the Enter button to return to the menu
screen.
Note:- The price of play on this machine is set within the Cashflow Coin Mech.
Ensure that the Game Cost is set to 1 Coin 1 Credit.
COIN OPTIONS 
GAME...

Page 47 6-3-2 Game Options
1. Select “GAME OPTIONS” on the menu screen to set the game
variables. the following screen is displayed.
2. Use the Select Up/Down switch choose the required item then press
the Enter button.
3. Use the Enter button to change the setting.
4. Select “EXIT” and press the Enter button to return to the menu
screen.
M E T INO I T P I R C S E DTE S Y R O T C A F
r e b m u n n o i t a c i n u m m o c k n i L ) a (4 - 1 e l b a t t e s - - - - r e b m u n r e y a l p o t r e b m u n B...

Page 48
6-3-3 I/O Test
1. Select “I/O TEST” on the menu screen to switches and lamps. The following screen is displayed.
2. Use the Select Up/Down switch choose the required item then press the Enter button.
3. Use the Enter button to change the setting. 
4. Select “EXIT” and press the Enter button to return to the menu scr\
een. 
(a) Shows the condition of the DIP Switches on the PCB. In normal operation all switches are OFF. (If a switch is ON, it will be displayed in red.)
(b) Shows the number of...

Page 49 6-3-3-1 Switch Test
1. Select “Switch Test” on the I/O menu screen to test the switches. The
following screen is displayed.
2. The display shows the current state of the switches.
3. Press the Up Select switch and the Enter switch together to EXIT and
return to the I/O menu screen
I/O TEST
DIP 3 12345678
LINK ON 1
SWITCH
(a) ................................GAS : 0000 SERVICE : OFF.............................  (g)
(b) ................................BREAK : 0000 VIEW :...

Page 50 6-3-3-2 Motor Test
1. Select “Motor Test” on the I/O menu screen to test the steering motor
and bike movements. The following screen is displayed.
2. Press the ‘View Change’ button to step through the tests.
3. To EXIT and return to the I/O menu screen, select NONE
OPERATION and press the Enter button.
I/O TEST
DIP 3 12345678
LINK ON 1
SWITCH
(a) ................................NONE OPERATION
(b) ................................STEER OFF±
00±
00
( c ) ................................BANK OFF±...