Multitech Multivoip 100 Model Mvp120 Voice/fax Over Ip Networks User Guide

61 Chapter 7 - Using the MultiVOIP Software
Multi-Tech Systems, Inc. MultiVOIP User Guideconnecting to the MVP120’s web server, you would look under the TCP section to see if any
connections are being established.  If not, that may indicate the web server is not enabled.  Or, if
you were having problems establishing a remote connection through TFTP, you could look in the
UDP section to see if any packets are being received.  If not, you may need to review your
network addressing.
SNMP Statistics
The SNMP...

62 Chapter 7 - Using the MultiVOIP Software
Multi-Tech Systems, Inc. MultiVOIP User Guide
Viewing Logs
The Log Entries dialog box displays a chronological history of all calls into and out of this unit.
This dialog box is opened by clicking Logs on the Statistics dialog box.
The Log Entries dialog box displays each call as a sequentially numbered Event with the date,
time, duration of the call, the status of the call (Successful or Unsuccessful), Mode (Voice  or
Fax), and the from and to numbers.
Viewing...

63 Chapter 7 - Using the MultiVOIP Software
Multi-Tech Systems, Inc. MultiVOIP User Guide
Viewing Channel Totals
The Channel Totals dialog box displays Outgoing and Incoming calls with their Attempted
and Completed numbers for each channel on this MVP120.  The Total Connected Time for
the channel is also displayed.  This can provide you with a sense of successful call
completions on each channel of the unit.
Reports
A report of the contents of the Log Entries dialog box can be generated using the...

64 Chapter 7 - Using the MultiVOIP Software
Multi-Tech Systems, Inc. MultiVOIP User Guide
Upgrade Procedures
Whenever you upgrade your version of the MVP120 software, you must first install the new
software on your PC. Then use the Upgrade Software function, the Factory Defaults, or
download the Firmware, the Voice Coders, and the H.323 stack to upgrade the MVP120 itself.
Before starting the upgrade process, view the current configuration and write down important
data such as your IP address, and voice...

65 Chapter 7 - Using the MultiVOIP Software
Multi-Tech Systems, Inc. MultiVOIP User Guide
5. Click OK when finished. The Checking MultiVOIP dialog box displays. When you click OK in
this box, theThe MultiVOIP firmware, voice coders, and H.323 stack are downloaded, and then
the MVP120 reboots.
Upgraded versions of the Boot Code (firmware, coders, and H.323 stack) can be downloaded
individually using the following manual procedures. 

66 Chapter 7 - Using the MultiVOIP Software
Multi-Tech Systems, Inc. MultiVOIP User Guide
Manual Upgrade Procedure
Follow this procedure only if you want to manually upgrade your MultiVOIP.
Note: Steps 4-8 may be performed via the command port or over IP.
1. Run MultiVOIP Configuration from your old version of the MultiVOIP software. Note the
current settings. Your MultiVOIP will be reset to factory defaults during this upgrade.
2. Unistall your old version of MultiVOIP software by selecting the Unistall...



	


Chapter 8
Remote Configuration and Management 

68 Chapter 8 - Remote Configuration and Management
Multi-Tech Systems, Inc. MultiVOIP User Guide
Chapter 8 - Remote Configuration and Management
This chapter provides procedures for viewing or changing the configuration of a remote unit.  Two
methods are provided to access a remote unit; the first method is modem based and the second
method uses IP.  Within the IP method, three applications can be used: 1) LAN-Based using
TFTP (Trivial File Transfer Protocol), 2) Telnet as a client application, or 3) a...

69 Chapter 8 - Remote Configuration and Management
Multi-Tech Systems, Inc. MultiVOIP User GuideIn the Dial String box, enter the AT command for dialing (ATDT) plus the phone number of
the remote MVP120.
If your Modem Initialization String, Initialization Response, or Connect Response values are
different from the defaults in the dialog box, refer to your modem user documentation and
change the default values to match your modem.
Click OK when you are satisfied with your selections.
6. Run the MVP120...

70 Chapter 8 - Remote Configuration and Management
Multi-Tech Systems, Inc. MultiVOIP User Guide
LAN-Based 
The LAN-based remote configuration requires a Windows Sockets compliant TCP/IP stack. TCP/IP
protocol software must be installed and functional before the configuration program can be used.
1. You must assign an Internet (IP) address for the PC and for each node that will be managed
by the configuration program. Refer to the protocol software documentation for instructions
on how to set the IP...