Mitsubishi Wd8200u Projector User Manual
Here you can view all the pages of manual Mitsubishi Wd8200u Projector User Manual. The Mitsubishi manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 51
EN-51 6. When selecting OK, the setting is completed as the IP ADDRESS stored. However, when selecting CANCEL, the setting is completed without storing. t 8IFOUIFTFUUJOHZPVFOUFSFEJTDPSSFDU UIF setting change dialog is displayed. After the dialog disappears, the NETWORK menu is displayed. If the entered content is not correct, the NETWORK menu is displayed after an error dialog is displayed. t *UNBZUBLFTPNFUJNFUPSFnFDUUIFTFUUJOHT Subnet Mask Settings 1. Display the IP CONFIG...
Page 52
EN-52 Initialization of Network Settings (See page 32 for menu setting.) 1. Display the NETWORK menu. 2. Press the or button to select NETWORK RESET. NETWORK RESET OK 3. Press the ENTER button. t $POmSNBUJPOEJBMPHBQQFBST 4. If pressing the ENTER button again, the Network Settings can be initialized. t *UNBZUBLFTPNFUJNFUPSFnFDUUIFTFUUJOHT How to Use Network Function t 8IFODPOOFDUJOHBDPNQVUFSBOEQSPKFDUPSXJUI LAN, configure the both IP Addresses in the same network group....
Page 53
EN-53 Lamp relay Using the lamp relay function, you can project images continuously. The lamp relay function automatically rests or switches the lamps. The lamp relay is performed when LAMP SELECT in the INSTALLATION 1 menu is set to DUAL or SINGLE. Setting the lamp relay interval When LAMP SELECT is set to DUAL: Either of the lamps is automatically put to rest. (See page 32 for menu setting.) 1. Display the INSTALLATION 1 menu. 2. Select LAMP SELECT by pressing the or button. 12LAMP SELECT...
Page 54
EN-54 t *NNFEJBUFMZBGUFSUIFQPXFSPO EVSJOHUIFMBNQ selection, or during the lamp relay operation, you cannot change the setting of LAMP SELECT and LAMP RELAY. t *OUIFDBTFPGDPOUJOVPVTQSPKFDUJPO UIFMBNQTNBZ deteriorate earlier unless they are turned off for 1 hour per week. t 8IFOVTJOHUIJTQSPKFDUPSDPOUJOVPVTMZGPSBMPOH time of period, enable LAMP RELAY. t 5IFCSJHIUOFTTBOEDPMPSUJOUWBSZBUUIFUJNFPG lamp switching. When LAMP SELECT is set to SINGLE: The lamps are...
Page 55
EN-55 t 5IFJNBHFXJUIJOUIFPVUFSFEHFTPGUIFSFE frame is captured. t 5IFDBQUVSFEJNBHFJTEJTQMBZFEJOUIF3&- mode automatically. CAPTURE : ENTER + ENTER CANCEL : MENUCAPTURE : ENTER X2 CANCEL : MENU 12.Adjust the size of the image to be captured so that such image stays within the red frame. tPress the , , or button to move the red frame. tYou can’t move the red frame outside the screen. tPress the MENU button to cancel the procedure. CAPTURE : ENTER X2 CANCEL : MENU 13. Press...
Page 56
EN-56 Password function This projector is equipped with the password function that is designed for prevention of wrong operation by children and restriction on operation by other than specified users. The password function has 3 modes as follows. DISPLAY INPUT .......... When the projector is turned on, the startup screen (or splash screen) will appear and stay on the screen until the password is entered. When the password is entered, the startup screen will switch to the regular operation...
Page 57
EN-57 Split You can split the screen in two and display a computer image on the left screen and a video image on the right screen. Left screenRight screen To use the split mode: 1. Press the SPLIT button on the remote control. t 5IFTDSFFOJTTQMJUJOUXPBOEUIFMFGUBOESJHIU screens display the following images: - Left screen: Image supplied to the last selected input source, COMPUTER1, COMPUTER2, DVI, or HDMI - Right screen: Image supplied to the last selected input source, VIDEO or...
Page 58
EN-58 Important: t 8IFOZPVTFU$0/530-4:45&.UP$3&4530/ in the NETWORK menu, the web control for Crestron is enabled. For such control, Adobe Flash Player should be installed in advance. You can download Adobe Flash Player from the website of Adobe Systems Incorporated. t 8IFOZPVTFU$0/530-4:45&.UP$3&4530/ in the NETWORK menu, you cannot use the control by ProjectorView Global+, which is the software supplied with the projector. About PJLink™ t 5PVTF1+-JOL
Page 59
EN-59 Connection For details of the connection, see “LAN control UTILITY operation manual” in the CD-ROM. When STANDBY MODE of the INSTALLATION 1 menu of the projector is set to LOW, the LAN network is disabled. To enable the LAN network, set STANDBY MODE to STANDARD. (See page 34 .) Configure the initial network settings first. You can configure the initial settings using the projector menu (see pages 49 to 52) or ProjectorView Global+. For details of ProjectorView Global+, see “LAN control UTILITY...
Page 60
EN-60 Monitoring and control using SERIAL terminal Using the SERIAL terminal, you can monitor and control multiple projectors collectively or individually. tFor details, contact your dealer. To RS-232C terminal To SERIAL INTo SERIAL INTo SERIAL IN To SERIAL OUTTo SERIAL OUT RS-232C cable RS-232C cable t See also the instruction manuals of the devices to be connected. Connection t Make sure that the power supplies of the projector and the computer are off. 1. Connect one end of an RS-232C...