Mitsubishi Wd8200u Projector User Manual
Here you can view all the pages of manual Mitsubishi Wd8200u Projector User Manual. The Mitsubishi manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 11
EN-11 Setting up your projector Before setting up Before setting up the projector, check the operating environment. If the environmental requirements are not satisfied, the projector may break down or fail. Setup environment The allowable operating temperature varies depending on the projection angle. For floor installation (projection angle 0°) and ceiling installation (projection angle 180°): +41°F (+5°C) to +104°F (+40°C) For installation at other angles: +41°F (+5°C) to +95°F (+35°C) For use in...
Page 12
EN-12 Setting up your projector (continued) Setup adjustment How to turn on the projector When you have to turn on the projector for setup adjustment, see the following pages: t 1MVHHJOHUIFQPXFSDPSE QBHF t 5VSOJOHPOUIFQPXFS QBHF t 5VSOJOHPGGUIFQPXFS QBHF Adjusting the position of the projected image Adjust the focus. If the projected image is out of the screen after the adjustment, adjust the projector position or the lens position using the lens shift function. 1. Press...
Page 13
EN-13 Setting the projector postureYou can select the posture of the projector. Set COOLING CONDITION in the INSTALLATION 1 menu according to the posture. Important: t *ODPOTJTUFODZCFUXFFOUIFQSPKFDUPSQPTUVSFBOE the menu settings may cause breakdown or failure of the projector or the lamp. t 8IFOZPVVTFUIFQSPKFDUPSJOUIF)*()-5*56%& mode, the selectable projector posture is floor installation (0°) and ceiling installation (180°) only. Setting the projection angle t 4FUCOOLING...
Page 14
EN-14 Setting up your projector (continued) Correcting skewed or distorted image For the best projection, project images on a flat screen installed at 90 degrees to the floor. If necessary, tilt the projector using the two adjustment feet on the bottom of the projector. Adjustment feet Screen 1. Tilt up the projector to the appropriate angle. 2. Rotate the adjustment feet for fine adjustment. Important: t %POUUSBOTQPSUUIFQSPKFDUPSXJUIJUTBEKVTUNFOU feet extended. Otherwise the adjustment feet...
Page 15
EN-15 Setting up your projector (continued) t 8IFOUIF,&:450/&NPEFBEKVTUNFOUJT performed, the displayed image may be distorted. t %FQFOEJOHPOUIFJOTUBMMBUJPODPOEJUJPOTPGUIF projector and the screen, a perfect rectangular image and the proper aspect ratio may not be obtained. Slight distortion can be corrected by the CORNERSTONE-mode adjustment. t /PJTFNBZBQQFBSPOUIFTDSFFOEVSJOHUIF KEYSTONE-mode adjustment because of the type of the video signal being projected and the setting...
Page 16
EN-16 Setting up your projector (continued) Adjustment using the CURVED mode To adjust images projected on a curved surface, press the ENTER/GEOMETRY button on the projector or the GEOMETRY button on the remote control to display the CURVED mode, and then press the , , or button to correct the distortion. CURVED ARC SELECT : BLANK : 0 : 0 Every time you press the BLANK button, the adjustment menu changes as follows: ARC → HORIZ. ORIGIN → VERT. ORIGIN → RESET → ARC... ARC...
Page 17
EN-17 t 8IFOUIFWFSUJDBMBSDBEKVTUNFOUJTQPTJUJWF PS the ARC is adjusted in the direction) Press the button. Press the button.Press the button. Press the button. When you press the or button in the RESET mode, the distortion correction is reset. Important: t 8IFOUIF$637&%NPEFBEKVTUNFOUUBLFTFGGFDU the resolution decreases. In addition, stripes may appear or straight lines may bend in images with complicated patterns. They are not due to product malfunctions....
Page 18
EN-18 Setting up your projector (continued) Front projection, ceiling mounting For ceiling mounting, you need the ceiling mount kit designed for this projector. Ask a specialist for installation. For details, consult your dealer. t 5IFXBSSBOUZPOUIJTQSPKFDUPSEPFTOPUDPWFSBOZ damage caused by use of any non-recommended ceiling mount kit or installation of the ceiling mount kit in an improper location. t 8IFOVTJOHUIFQSPKFDUPSNPVOUFEPOUIFDFJMJOH set IMAGE REVERSE in the INSTALLATION 1...
Page 19
EN-19 2 1 Viewing computer images 2 1 A. Connecting the projector to a computer Preparation: t .BLFTVSFUIBUUIFQPXFSPGUIFQSPKFDUPSBOEUIBUPGUIFDPNQVUFSBSFUVSOFEPGG t 8IFODPOOFDUJOHUIFQSPKFDUPSUPBEFTLUPQDPNQVUFS EJTDPOOFDUUIF3(#DBCMFUIBUJTDPOOFDUFEUPUIFNPOJUPS For analog connection: (For using the COMPUTER/COMPONENT VIDEO IN-1 terminal.) 1. Connect one end of the supplied RGB cable to the COMPUTER/COMPONENT VIDEO IN-1 terminal of the projector. 2. Connect the...
Page 20
EN-20 Viewing computer images (continued) 1. Plug the attached power cord into the power cord inlet of this projector. 2. Plug the other end of the power cord into a power outlet. t 5IFQPXFSDPSETGPSVTFJOUIF64BOE&VSPQFBSFJODMVEFEXJUIUIJTQSPKFDUPS6TFUIFBQQSPQSJBUFPOFGPSZPVS country. t 5IJTQSPKFDUPSVTFTUIFQPXFSQMVHPGQJOHSPVOEJOHUZQF%POPUUBLFBXBZUIFHSPVOEJOHQJOGSPNUIFQPXFS plug. If the power plug doesn’t fit your wall outlet, ask an electrician to change...