Mitsubishi Wd8200u Projector User Manual

EN-41
INFORMATION menu
60.00 Hz RESOLUTION
1024 x 768
VERTICAL
FREQUENCY
48.36 kHz
5WIRE HORIZONTAL
FREQUENCY
SYNC. TYPE SERIAL NUMBER
INFORMATION1 12 2
FILTER TIME*****H / ****TIMES
********... NEXT LAMP RELAY
COMPUTER1 INPUT
opt.
*D **H 
RG
HVB
LAMP 1 TIME (LOW)
LAMP 2 TIME (LOW)
****H****H
ITEM DESCRIPTION
LAMP 1 TIME (LOW)
This item shows the lamp operation time calculated based on that the LAMP MODE of LAMP 1 
is LOW.  
t
 8IFO
UIF
-.1
.0%&
JT
45/%3%...

EN-42
Adjusting projected images
To adjust the brightness (CONTRAST and BRIGHTNESS):
You can make adjustments for the brightness of the projected image using the menu. 
(See page 32 for menu setting.) 
1.  Display the IMAGE menu. 
2.  Select CONTRAST or BRIGHTNESS by pressing the  or  button. 
3.  Adjust the selected item by pressing the  or  button. 
To cancel the menu:
4.  Press the MENU button. 
CONTRAST 
Select to adjust the contrast of the image. Every time the  button is pressed, the image...

EN-43
To cancel the menu:
7.  Press the MENU button. 
To enable the stored color temperature: 
1.  Set COLOR TEMP. to USER 
 in the IMAGE menu. 
About color temperature
Color temperature is a way to show the differences in white. White of which temperature is low appears reddish. 
When the color temperature rises, white appears bluish. For example, you can change the color temperature using 
the following procedures. 
To raise the color temperature: Increase the CONTRAST B (blue) and decrease the...

EN-44
Adjusting the fineness of the image (SUPER RESOLUTION): 
You can adjust the fineness of the image using the menu.  
(See page 32 for menu setting.) 
With the IMAGE menu:
1.  Display the IMAGE menu. 
2.  Select SUPER RESOLUTION by pressing the  or  button. 
3. Press the  or  button to select ON 
. 
4.  Press the ENTER button.
5.  Make adjustment using the  or  button.  
Important:
t
When you make SUPER RESOLUTION adjustment, the colors of the menu may be obscured, but this is not a 
failure....

EN-45
Adjusting projected images (continued)
How to adjust the computer image
This projector automatically selects a proper signal format according to the type of video signal supplied from the 
computer. However, video signals from the computer may not be projected correctly depending on the types of the 
computer and images to be projected. In such a case, make adjustment according to the flowchart below.
Adjustment is completed. When the size and position of 
the computer image are not correct....

EN-46
How to adjust the image supplied from the computer using the menu:
Carry out the following procedures according to the symptoms. 
Wide strips appear.  ……………………………………… Adjust TRACKING in the SIGNAL menu. 
The projected image flickers. 
The projected image is blurred. ......................................Adjust FINE SYNC. in the SIGNAL menu. 
The projected image is displaced horizontally. ..............Adjust HORIZ.POSITION in the SIGNAL menu. Every time the 
 button is pressed, the image moves to...

EN-47
11. Press the ENTER button.
SETTING - BLACK LEVEL
INTERLOCKED
RED
GREENON
0
0
BLUE
0
12. Select an item you want to set by pressing the  or 
 button.
t
 EKVTU
UIF
CMBDL
MFWFM
JO
BSFBT
PUIFS
UIBO
UIF

overlapped areas. 
t
 8IFO
ZPV
TFU
*/5&3-0$,&%
UP
0/

ZPV
DBO

adjust RED, GREEN, and BLUE simultaneously. 
When you set it to OFF, you can adjust RED, 
GREEN, and BLUE separately. 
13. 
Select a setting value by pressing the  or  button. 
Repeat steps 12 to 13, if necessary. 
14. Press the MENU...

EN-48
7.  Select an item you want to set by pressing the  or 
 button.
t
 
4FMFDU
UIF
DPMPS
ZPV
XBOU
UP
BEKVTU
VTJOH

COLOR.
8.  Select a setting value by pressing the  or  
button.
t
 :PV
DBO
FOUFS
OVNCFST
CZ
QSFTTJOH
UIF
OVNCFS

buttons (0 to 9) while holding down the NUM 
button on the remote control. 
Repeat steps  7 to 8, if necessary. 
Important:
t
 5IF
DPMPS
UPOF
NBZ
OPU
CF
EJTQMBZFE
DPSSFDUMZ

depending on the setting value. Set the value within 
the proper range.
Set the target values of the...

EN-49
Initial network settings
You can set the network of the projector using the 
menu.
NETWORK CONTROLLER
NETWORK PASSWORD
NETWORK1 12 2
NETWORK CERTIFICATION PROJECTOR NAME
IP CONFIG
NETWORK RESET
opt.
STANDARD
ENTER
ENTER
OK
ON
Setting Projector Name
(See page 32 for menu setting.)
1.  Display the NETWORK menu. 
2. Press the  or  button to select PROJECTOR 
NAME.
PROJECTOR NAMESET
3. Press the  or  button to select SET .
4.  Press the ENTER button.
t
 130+&$503
/.&
TDSFFO
BQQFBST
PROJECTOR NAME...

EN-50
6.  Enter the NEW NETWORK PASSWORD and 
CONFIRM NETWORK PASSWORD.
t
 1BTTXPSE
DBO
CF
TFU
VTJOH
VQ
UP

DIBSBDUFST

including alphabets (capital/small) or numeric 
characters.
← key: ............. Shifting the position of enter 
cursor to the left for each 
character.
→ key: ............. Shifting the position of enter 
cursor to the right for each 
character.
 key: ...............  Shifting the position of 
enter cursor between NEW 
NETWORK PASSWORD 
and CONFIRM NETWORK 
PASSWORD.
DEL key:...