Mitel Voice Processing Solutions Instructions Manual

Hardware Installation and Configuration 
ar 
The Ethernet card cannot coexist in the same module with the following cards 
because of interrupt conflicts: 
e Smartcard (2,4, or 8 port serial card) 
a 
PROSE TTS card 
Do not include an Ethernet card in the same module as any of the above cards. 
nfiguring the Hardware 
This section shows how you must configure the Ethernet to use the Unified TCP/IP 
optional feature successfully. 
Configuring the Ethernet Card 
There are two different ways to configure an...

sk Lis 
Page 1 of 1 
VoiceMemo Release G.OA and later 
Task Procedure 
Install Ethernet Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cl? 2149 
Connect the Server to the Network . . 
_ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . cl? 2150 
Shut Down a Server . . . . . ....

Install the EtherTPI-lG+T Ethernet Card 
Page 1 of 2 
VoiceMemo Release 6.OA and later 
This procedure describes how to install the Alta EtherTPI- 16+T Ethernet card in a 
Series 6 server for use with the Unified TCPlIP optional feature. 
ote: You perform diagnostic and troubleshooting tasks after you install and 
configure Unified TCPlIP on the server. See CP 6472, “Test Unified 
Step TCP/IP Configuration,” in Chpater 4, for instructions. 
1. Make sure that you are wearing an electrostatic discharge...

Cl? 2149 
Page 2 of 2 
VoiceMemo Release G.OA and later 
Figure ‘I 
Alta EtherTPI-16+T Ethernet Card 
Dot. Rev. A  

Connect the Server to the Network Page 1 of 2 
VoiceMemo Release 6.OA and later 
This procedure tells you how to connect the Ethernet card in the Series 6 server to the 
Ethernet network, using twisted-pair cable. 
ote: The network administrator must pull cable to the server and provide you with a 
Step network connection before you perform this procedure. 
(QTJ) 
onnect Ethernet 
to iste 
1. Insert the modular plug shown in Figure 1 into the RJ-45 port on the Ethernet 
card. 
Ethernet Card 
b 
 
/ 
,...

Cl’ 2150 
Step 
Link (green) 
TransmitlReceive (red) 
Collision (red) 
Polarity (red) 
Figure 2 LEDs on Ethernet Card 
Page 2 of 2 
VoiceMemo Release 6.OA and later 
Reference 
Doe. RN. A  

CP 
Shut Down a Server 
Page 1 of 2 
VoiceMemo Release 6.OA and later 
This procedure describes how to shut down a module or an entire Series 6 server. You 
should use this procedure before turning off the power to a module, as the shutdown 
command halts call processing in a clean and orderly fashion. 
G! 
You should follow the policies of the site to warn users prior to the server 
shutdown. This process removes the server from call processing. Centigram 
recommends that you perform this procedure only...

cl? 5700 
Page 2 of 2 
VoiceMemo Release 6.OA and later 
Step 
6. Specify if changes to the status of each module are to be made. 
prompt: 
Enable or Disable Modules? 
Response: Y to change the status of modules, OY 
N to keep the module status the same and continue at step 
11 
7. Ifyou answered yes in step 6, achartwiththe~~ofeachmoduleisdisplayedandthenthe 
Module Maintenance Menu is displayed. 
8. Enable a module, if necessary: 
Select: (E) ENABLE a module 
prompt: Which Module? 
Response: The number...

: 
.’ 
This chapter covers reference information relating to the Unified TCP/IP software, 
including installation and configuration. Refer to the Task List for step-by-step 
instructions on software installation and configuration. 
in 
e ie re 
This section provides an overview on installing the Unified TCP/IP software on your 
Series 6 server. 
Note: For complete step-by-step directions, refer to the procedures at the 
end of this chapter. 
Installing the Unified TCP/IP Optional 
You install the Unified...