Mitel Sx 200 Ml Pabx Lightware 16 Instructions Guide

1 Introduction 
Installation Information 
Intent of this Document 
1.1 This practice describes the installation procedures for the SX-200@ ML PABX, in 
addition to the MlTEL@ peripheral equipment designed to be used with them. 
Intended Audience 
This practice is designed for MITEL-trained installation and maintenance technicians. 
The System: The 96-pot-t cabinet, consisting of a single bay, holds one Main Control 
Card II (MCC II), a Bay Control Card, a Bay Power Supply, and up to eight Peripheral...

Installation Information 
Table l-l Installation Information 
Part 
Part 2 
Part 3 
Part 4 Title 
Contents 
Installing System 
- Equipment part numbers and outlines of 
installation procedures. 
- Prepare for installation 
Handling Printed Circuit Cards 
- Unpack and handle printed circuit cards 
- Remove and return printed circuit cards 
Installing Digital Peripheral Cards Installation of: 
and Modules 
- the Universal Card 
- the ONS, OPS, and Digital Line Cards 
- the DID Trunk Card 
- the LS/GS Trunk...

Introduction 
Chart l-l How to Use This Practice 
Step Action Comments 
install Equipment 
1. Refer to the appropriate part of this document 
for the PABX configuration you are installing. 
2. Consult the tables at the beginning of each The tables tell you what equipment is to be 
part. installed, and in what sequence. 
3. Follow the installation charts in the sequence 
given in the table. 
install Peripheral Equipment 
4. When the cabinet and circuit cards are 
installed, refer to the feri@era/ Devices...

InsWa~ion Information 
Table l-2 Referenced MITEL Documents 
Practice Number Title Contains Information On 
9109-098-126-NA Peripheral Devices All peripherals, including SUPERSETTM 
telephones, consoles, datasets, and 
other devices, and the installation 
procedures for those devices 
9109-098-I 80-NA Engineering Information Configuring the system 
9109-098-210-NA Customer Data Entry (CDE) Programming the PABX when 
hardware installation is complete 
1 9109-098-350-NA 1 Troubleshooting 1 Problems during...

2 Installing the System 
Installing the SX-200 ML PABX 
Introduction 
2.1 The equipment to be installed to create the system is shown in Table 2-l. Some of the 
equipment listed as requiring installation may have been shipped already installed. If 
that is the case, the equipment should be removed and reseated during the 
installation procedure. 
Table 2-l Equipment Installed in the SX-200 ML PABX 
Cabinet The cabinet is shipped preconfigured with 
- Main Control II Card 
- Bay Control Card 
- Bay Power...

lns~allation InformaGon 
ML 
LIGHTIMARE 16 software 
stem documentation 
Note: The SX-200 ML PABX has been evaluated and listed with Underwriter’s Laboratories lnncorpo- 
rated to their standard for safety 1459, ‘Telephone Equipment”, second edition. The denoted 
assemblies have been investigated and determined suitable for use in this product. 
Installation Charts 
Table 2-3 indicates which charts to follow in sequence to install the SX-200 ML PABX. 
2-2 ls:de 1 Revision 0 March 1997  

Installing the System 
Table 2-3 Charts to Follow to Install the SX-200 ML System 
I 
Prepare for Installation Activity Basic Chart 
Prepare for Installation 1 Chart 2-l 
I 
Install Cabinet 
Unpack and Inspect Cabinet 1 x 1 Chatt2-2 1 
Open and Close Front Door 
Install Cabinet (the cabinet is pre-configured with Control cards) 
Verify Ground Connection X Chart 2-3 
X Chart 2-4 
X Chart 2-5 
Handle Printed Circuit Cards 
Unpack and Handle Printed Circuit Cards Chart 3-l 
I 
Remove and Repack Printed...

lns~alla~ion Information 
Prepare for Installation 
2.2 When you have completed Chart 2-i you will have: 
l Made sure that the site survey information is available. 
l Made sure that the system configuration information is available. 
l Assembled the material you need for the installation. 
l Provided additional ac outlets if required. 
Chart 2-l Prepare For installation 
Step Action Comments 
Prepare For Installation 
1. Make sure all stations, trunks, and other equipment This information is usually...

Installing the System 
Chart 2-2 Unpack and Inspect an SX-200 ML Cabinet 
Step Action Comments 
Remove Cabinet from Carton 
1. Set aside all other packaged items for later unpacking 
and installation. 
2. Unpack carton and check contents against packing list. 
Retain some packing material in case any items are to 
be returned. 
3. Remove the cabinet from the carton. 
inspect for Transit Damage 
4. Visually check that the cabinet and all atiached 
equipment is undamaged. 
5. Open the cabinet front door....

Installation Information 
Chart 2-3 Open and Close Cabinet Front Door 
Action 
Open Cabinet Front Door 
Pry open the two latches on the right-hand side of the 
black cover panel on the front door, and swing the 
cover panel off to the left. 
Loosen the two screws under the black panel to 
release the front door panel. 
Pull the top of the front door out from the cabinet and 
lift it off the lower front cabinet rail. 
Close Cabinet Front Door 
Lower the front door panel down over the front cabinet 
rail...