Mitel SX-200 DIGITAL Pabx General Description Manual

Features Description 
4.78 SYSTEM IDENTIFIER 
Description 
This feature allows a unique identifier to be assigned to the system. 
This code identifies the system when central polling equipment is used 
for traffic data collection. 
Conditions 
This is done from the Attendant Console. 
Programming 
None 
Operation 
To set a system identifier, enter the following: 
FUNCTION 
A-lT FUNCTION 
SYSTEM IDENT 
(enter the desired System Identity number) 
SET 
To view the current system identity number: 
FUNCTION...

Features Description 
4.79 TANDEM OPERATION 
Description 
The 5X-200’ DIGITAL PABX can support a tandem operation arrange- 
ment, using Tie trunks to connect two systems together. 
Conditions 
Appropriate Automatic Route Selection (ARS) must be provided. 
Programming 
None 
Operation 
None 
Page 4-86  

Features Description 
4.80 TENANTING 
Description 
Tenanting is a feature of the SX-ZOO@ DIGlTAL PABX which allows 
several customers, each with independent Attendant Consoles, to 
share the same system. 
The system can be programmed to enable each tenant’s section of the 
system to be completely independent of other tenants; 
calls between 
tenants can be made only through CO trunks. 
Tenanting can also be used to segregate different departments of the 
same company. In this case, all departments can...

Features Description 
4.81 TOLL CONTROL 
Description 
The Toll Control feature forms part of the Automatic Route Selection 
(AK) feature. It allows a means to restrict the calls that certain groups 
of extensions may place. This may mean denying all outside calls, 
denying calls to specific locations, denying calls over expensive routes, 
or any combination of these. 
See AUTOMATIC ROUTE SELECTION (ARS). 
Conditions 
See Section MITLS 108-093-2’13-NA, Automatic Route Selection. 
Programming 
See Sections...

Features Description 
4.82 TONE DEMONSTRATION PACKAGE 
Description 
This is a special facility to train the user to recognize the various tones 
generated by the system. 
Conditions 
None 
Programming 
Assign an access code to Feature 27 (Tone Demonstration). 
Operation 
Dial the tone demonstration package feature access code plus the 
code for the tone you wish to hear: 
10 - Silence 
11 - Dial Tone 
12 - Transfer Dial Tone 
13 - Busy Tone 
14 - Special Busy Tone 
15 - Standard Ringback Tone 
16 -...

Features Description 
4.83 TONE PLAN 
Description 
To accommodate the numerous tones which can be generated when 
dialing telephone numbers in the North American region, the system 
has the North American tone plan co-existing on the same system’s 
floppy disk as the Ringing Plan. 
Conditions 
None 
Programming 
None 
Operation 
None 
Page 4-90  

Features Description 
4.84 TRAFFiC MEASUREMENT 
Description 
Traffic measurements can be made on SX-ZOO@ DIGITAL PABX sys- 
tems, and the results presented at the RS-232C printer port for a 
suitable output device (printer or magnetic tape unit). The types of 
measurements made include the following: 
DTMF Receiver usage 
PCM Channel usage 
Console usage 
Trunk group usage 
Trunk usage 
. 1 s dial tone 
2 s dial tone 
3 s dial tone 
Console calls 
Dial 0 calls 
Extension origins 
Intercepted calls...

Features Description 
Conditions 
See. Section MITLSI 08-093-450-NA, Traffic Meaqurement for details. 
Programming 
See Section MITL9108-093-450-NA, Traffic Measurement for details. 
Operation 
See Section MITL9108-093~450-NA, Traffic Measurement for details. 
Page 4-92  

Features Description 
4.85 TRUNK CIRCUIT DESCRIPTOR OPTIONS 
Description 
Trunk circuit descriptors specify the programmable hardware param- 
eters of each trunk circuit in the SX-200@ DIGITAL PABX. These are 
complemented by the switch settings on the analog SX-2OO@ trunk 
card types. The system supports a maximum of 25 different trunk 
circuit descriptors. All trunks in the system must have a trunk descrip- 
tor number with an associated set of selected options. Table 4-1 lists 
the trunk descriptor...

Features Description 
TABLE 4-1 (CONT’D) 
TRUNK HARDWARE OPTIONS 
Trunk Type: E&M MODULE 
Iar-End Gives Answer Supervision 
nhibit Automatic Supervision 
Vo Seize Alarm 
Vo Release Alarm 
roll Office 
s this a CO 
XTMF 
mpedance [Use DIP Switch on the Module to Program 
(600 Ohms or Complex) 
E Lead invert 
M Lead Invert 
Ignore Remote Disconnect 
Disconnect Timer (150 - 300 ms) x (50 ms increments) 
Release Acknowledge Timer (2000 - 9900 ms) x (100 ms inc) 
Guard Timer (200 -1000 ms) x (100 ms...