Mitel Sx-100, Sx-200 Attendant Console Guide

VOLUME/TONE RINGER 
1 
l To adjust the volume of the tone 4 0 To turn the ringer ON, press BELL 
ringer, use the control on the back 
OFF key again 
of the console 
0 BELL OFF lamp goes out; the tone 
ringer is now reconnected 
2 OTo turn the ringer OFF, press BELL 
OFF key 
3 l BELL OFF lamp lights; the tone 
ringer is now disconnected 
B39 . 
‘.I :: 
_._.‘.. 
:L:;‘. 
,_-.. :. 
.^_F._. 
..--.--, _.. 
.: : .,: : - 
:  

HOTEL FEATURES  

AUTOMATIC WAKE-UP (SETTING) 
To set or change: 
I 0 Press GUEST ROOM key 
0 Dial extension number (not 
required if connected to extension) 
0 GUEST ROOM lamp lights 
2 Source display shows: 
0 Number dialed 
0 Message register 
0 ATT lamp lit 
3 Destination display shows: 
0 Room status code 
0 Wake-up time if set 
4 0 Dial >k, wake-up time, then # 
(or >I< if IP-hour clock for PM) 
5 Destination display shows: 
0 Room status code 
0 Wake-up time (P if PM) 
6 0 Press RELEASE key 
0 Destination display...

AUTOMATIC WAKE-UP 
(CANCELING) 
To cancel: 
1 a Press GUEST ROOM key 3 Destination display shows: 
0 Present wake-up time (P if PM 
0 Dial extension number (not 0 Room status code 
required if connected to extension) 
1 
0 GU’EST ROOM lamp lights - 
4 0 Press * # (or **) 
0 Wake-up time display clears 
: 
2 Source display shows: 
0 Extension number 
0 Message register displayed 
5 0 Press RELEASE key 
0 All displays clear 
NOTE: If a printer is used a record is 
printed when the RELEASE key is 
pressed.  

r-7 CAL’ El  mb AOCKINGI 
 - 
ROOW’6ROOM RESTRICTION : 
Calls between guest rooms can be 
prevented by using the call blocking To remove call blocKuW 2 0 Press CALL BLOCK key 
l CALL BLOCK lamp goes out 
feature* 
‘ta set up call blocking: 
_ 
m_ - 
I 
0 Press CALL BLOCK Key 
l CALL BLOCK lamp lights  

DO NOT DIWURB 
(SET UP/DISPLAY) 
To set up Do Not Disturb: 
1 @Press GUEST ROOM key 
OGUEST ROOM lamp lights 
0 Dial extension number 
2 Source display shows: 
0 Extension number 
0 Message register 
l ATT lamp lit 
3 0 Press DO NOT DSTB key 
0 DO NOT DSTB lamp lights 
0 Busy lamp field shows extension 
busy 
4 0 Press RELEASE key 
0 All displays clear 
@ Busy lamp field shows extension 
busy 
Automatic Wake-up will override Do Not 
Disturb. To display which guest rooms have Do 
Not Disturb applied: 
1 0...

DO NOT DISTURB [CANCEL) 
ho cancel Do Not Disturb: 
1 0 Press GUEST ROOM key 
e Dial extension number 
0 GUEST ROOM lamp lights 
0 DO NOT DSTB lamp lights 
2 
Source display shows: 
0 Number dialed 
0 Message Register 
0 ATT lamp lit 
3 
0 Press DO NOT DSTB key 
0 DO NOT DSTB lamp goes out 
3 
0 Press RELEASE key 
0 Source display clears  

MESSAGE REGISTER 
To request a print of room call counts: 
1 @Dial >t

,MESSAGE REGISTER 
OF AN EXTENSION 
1 0 Press GUEST ROOM key 
0 GUEST ROOM lamp lights 
0 Dial extension number 
l ATT lamp lit 
2 Source display shows: 
0 Extension number 
l The number of local call units made 
from the room. The display can 
show a value of up to 9999. After 
this, decimal points are lit in 
sequence starting from the right of 
the display, to indicate an 
increment of 10,000; e.g., a display 
of 43.2.8. denotes a value of 34328 
3 Destination display shows: 
0 Room status code...

MESSAGE WAITING (SET UP) 
Using the GUEST ROOM key: 
1 0 Press GUEST ROOM key 
0 GUEST ROOM lamp lights 
0 Dial extension number 
2 Source display shows: 
0 Number dialed 
l ATT lamp lit 
0 Message Register 
3 Destination display shows: 
0 If MSGE WAIT lamp is lit, extension 
has a message waiting OR 
0 If MSGE WAIT lamp is out, press 
MSGE WAIT key 
0 MSGE WAIT lamp lit 
4 At extension: 
0 Extension message waiting lamp 
flashes or extension rings every 20 
minutes 
5 0 Press RELEASE key 
0 All displays...