Home > Mitel > Communications System > Mitel SMART L CALL CONTROLLER Hardware Installation Manual

Mitel SMART L CALL CONTROLLER Hardware Installation Manual

Here you can view all the pages of manual Mitel SMART L CALL CONTROLLER Hardware Installation Manual. The Mitel manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 371

SECTION iVllTL8350-048-l OO-NA 
5) 
Note: 
7.144 
‘7nnn’ and ‘BB’ entries are not counted. 
Access Control strings, OCC Access Numbers, OCC Authoriza- 
tion Codes, etc., all count, but in general require so little space 
that they may be neglected for the purpose of space estima- 
tions. 
Deleting a callback (Speed Call) with the ‘7nnnBB’ command 
does not reclaim all memory previously occupied by that 
entry. After deletion, the memory space increase only by the 
number of digits in the removed callback...

Page 372

SECTION MITL8350-048-IOO-NA 
(5 + 2)2X + (7 + 6)X = 14,500 
(7)2X + 13X = 14,500 
14x + 13x = 14500 
27X = 14500 
14500 
x= 27 
x = 537 
Therefore, 1,074 five digit passwords (2X) and 537 seven digit callback 
numbers may safely be stored in the RAM memory. 
7.148 If the extreme case were considered and based on the formula 
above, up to 381 15-digit passwords and 381 15-digit callback 
numbers could be stored in the RAM memory. For those who demand 
more detailed calculations, simultaneous solutions...

Page 373

SECTION MlfL8350-048-l OO-NA 
SEARCH TABLES 
rr 
PASSWORDS 
Parameters 801 - 815 
Parameters 821 - 835 
Length+1 
I 
X QW- Subtotal 
Length+2 
- 
X 
= Qty. 
Subtotal 
i I; I I 
~: -- 
I 
. 
: : 
I I 
; : 
i i 
i i 
I 
-i 
‘; 
j 
I 
i/i 
I 
I i 
I 
i 
I_ 
Page 79  

Page 374

SECTION MlTL8350-048-l OO-NA 
CALLBACK NUMBERS 
7nnn Entries 
Length+6 X Qty. 
Subtotal 
Total Space 
Figure 7-9, Calculation Sht. 3 
Page 80  

Page 375

SECTION MITL8350-048-IOO-MA 
8. TECHNICAL CIRCUIT DESCRIPTION 
INTRODUCTION 
8.01 
This part will be added at a later date. For the present, refer to 
Appendix C, Figures C-I and C-2 for an overall block diagram, 
and a simplified electrical diagram of the Controller, respectively. 
Page 81  

Page 376

SECTION MITL8350-048-l OO-NA 
Page 82 --- THIS PAGE INTENTIONALLY LEFT BLANK ---  

Page 377

SECTION MITL8350-048-l OO-NA 
9. MAINTENANCE AND TROUBLESHOOTING 
MAINTENANCE 
9.01 The SMarT-1’” Security Access Controller, as is evident, is a 
fully self-contained unit. As such, it has no user repairable 
parts. If the warranty seal over the unit fasteners is broken, the war- 
ranty is void. In case of failure, replace the Controller as follows: 
1) Power down the unit. This will cut-through the subscriber side 
to the CO side. 
2) Remove the RJ31KA31 plug from the Telco supplied socket. 
The...

Page 378

SECTION MITL8350-048-l OO-NA 
--- THIS PAGE INTENTIONALLY LEFT BLANK --- 
Page 84  

Page 379

SECTION MlTL8350-048-l OO-NA 
APPENDIX A 
FCC INTERCONNECTION REQUIREMENTS 
Al.01 
This equipment has been approved by the Federal Communica- 
tions Commission (FCC) as not being harmful to the telephone 
network when connected directly to the telephone lines through the 
standard connection cabling provided with the unit. This section is 
applicable to telephone interconnection in the United States. 
Al.02 Prior to the interconnection of this equipment, the local tele- 
phone company is to be notified;...

Page 380

SECTION MITL8350-048-l OO-NA 
Al .06 There are no user repairable parts within the unit. It is sealed 
against user maintenance. If opened, all warranties are voided. 
Al .07 No cabling or wiring changes within the unit are permitted by 
the user. Plug-ended cables, as detailed in this document, are 
used for ail external connections between the unit and the 
to be 
telephone company interface jack. 
Al.08 Power supply components and cabling is only to be changed or 
maintained by MITEL DATACOM INC. or...
Start reading Mitel SMART L CALL CONTROLLER Hardware Installation Manual

Related Manuals for Mitel SMART L CALL CONTROLLER Hardware Installation Manual

All Mitel manuals