Miele Kfn 14947 Sdeed Operating And Installation Instructions

^Remove coverd.
The soft-close mechanism is now no
longer fixed to the appliance.
^Remove panela.
^Slide soft-close mechanism bracket
fas far as it will go towards the
handle side of the door.
^Undo screwgon the soft-close
mechanism and on the spacer.
^Using a flat-bladed screwdriver prise
up the centre of the base of the
soft-close mechanism towards the
middle of the door.
^
Then prise the base of the soft-close
mechanism out of the socket from the
hinge side of the door.
^
Place the soft-close...

Caution. The upper door is not
secure as soon as the upper hinge
plate is removed.
^Close the upper door.
^Undo screwsmin upper hinge plate
nand pull it upwards and off.
^Carefully lift the upper door off and
place it to one side.
^Make sure that you leave the hinge
pin in the hinge plate in the middle of
the appliance, as otherwise the lower
door will be unsecured.
^Then fit coverhtogether with
retainerion the opposite side.
^Refit coverlon the opposite side.
Removing the lower soft-close door...

^Push hinge pineup and out from
underneath.
The soft-close mechanism is now no
longer fixed to the appliance.
^Remove panela.
^
Slide soft-close mechanism bracket
fas far as it will go towards the
handle side of the door.
^
Undo screwgon the soft-close
mechanism and on the spacer.
^
Using a flat-bladed screwdriver prise
up the centre of the base of the
soft-close mechanism towards the
middle of the door.
^
Then prise the base of the soft-close
mechanism out of the socket from the
hinge side of the door....

^Remove caplfrom the bush in the
door and refit on the opposite side.
Refitting the lower door
^
Remove coveraby pulling it
forwards.
^
Pull coverboff.
^
Screw the foot into hinge pincas far
as it will go.^With the help of another person,
carefully tilt the appliance backwards
and pull hinge pincout.
^Take care not to lose hinge bushd.
^Undo screwseand take hinge plate
foff.
^Remove covergand undo the
screws. Refit the screws and cover on
the opposite side.
^Refit hinge platefonto the other
side using...

^Fit hinge piniinto middle hinge
platekin the lower door.
Replacing the lower soft-close door
mechanism
^
Remove coverafrom panelb,
rotate it by 180° and refit it on the
other side.^Insert the spacer into the socket on
the handle side (A).
^Then insert the soft-close mechanism
into the socket on the hinge side (B).
Push both parts from the middle
towards the outside so that they
click firmly into position.
^
Attach the spacer and the soft-close
mechanism securely using screwc.
Changing the door hinging
65
 

^Attach panelbto soft-close
mechanism bracketd.
^Align bracketdto the hinge plate,
and insert pinefrom above so that
the right angle fits into the recess.
^Click coverfback into place.
Make sure that coverffits properly so
that the door can be closed without
hindrance and the pin is protected.
^Remove retaining clipg.
^
Replace panelbonto the soft-close
mechanism from above, clicking it
back into place first at the bottom
and then at the top.
^
Close the lower appliance door.Refitting the upper door:...

Replacing the upper soft-close door
mechanism:
^Remove coverafrom panelb,
rotate it by 180° and refit it on the
other side.
^
Insert the spacer into the socket on
the handle side (A).
^
Then insert the soft-close mechanism
into the socket on the hinge side (B).
Push both parts from the middle
towards the outside so that they
click firmly into position.^Attach the spacer and the soft-close
mechanism securely using screwc.
^Attach panelbto soft-close
mechanism bracketd.
^
Push covereon from the side so...

^Remove retaining clipg.
^Replace panelbonto the soft-close
mechanism from above, clicking it
back into place first at the bottom
and then at the top.
^Close the upper door.
Refitting the handle:
Please make sure you follow the
instructions below carefully when
you refit the handle. The door seal
will be damaged if the handle is
fitted incorrectly.
^
Loosely attach the handle to the
opposite side of the door with the two
front screwsb.Mounting platecmust be positioned
on the side of the door so that when...

The appliance doors can be aligned
with the housing after they have been
fitted.
In the following illustration the door
is not shown in the closed position to
make it easier to see what you have
to do.
Align thelower doorusing the long
outer slots in the lower hinge plate:
^Remove centre screwafrom the
hinge plate.
^
Slightly loosen both outer screwsb.
^
Align the door by sliding the hinge
plate to the left or right.
^
Then tighten screwsbagain. Screw
adoes not need to be used again.Align theupper...

aTop box
bAppliance
cHousing unit
dWall
The appliance can be installed in a
kitchen run. To match the height of the
rest of the kitchen, the appliance can
be fitted with a suitable top boxa.
A ventilation gap of at least 50 mm
depth must be allowed for behind the
appliance across the entire width of the
top box for air to circulate.
The cross section of the air outlet under
the room ceiling must be at least
300 cm
2to ensure that air can circulate
without hindrance. Otherwise the
appliance has to work...