Miele Kfn 14947 Sdeed Operating And Installation Instructions

Normal noises What causes them
Brrrrr...Humming noise made by the motor (compressor). This noise can
get louder for brief periods when the motor is switching on.
Blubb, blubb....A gurgling noise can be heard when coolant is circulating
through the pipes.
Click....Clicking sounds are made when the thermostat switches the
motor on and off.
Sssrrrrr....On multi-zone and frost-free appliances you can sometimes just
hear the movement of air circulating inside the appliance.
Remember that the noise of the...

In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
–your Miele Dealer
or
–Miele
(see back cover for contact details).
When contacting your Dealer or Miele,
please quote the model and serial
number of your appliance. This
information is given on the data plate
inside your appliance.
Please note that telephone calls may
be monitored and recorded for
training purposes.
N.B. A call-out charge will be applied
for service visits where the problem...

Notes on connecting to the
mains water supply
Connection to the mains water
supply should only be carried out by
a qualified and competent person in
accordance with national and local
regulations.
The water quality must conform to
the requirements for drinking water
in the country the appliance is being
installed in.
– This appliance complies with IEC
61770 and EN 61770 (ATS 5200.101
in Australia).
– All items used for connecting the
appliance to the mains water supply
must comply with the current...

^The stainless steel hose should be
attached to the solenoid valve at the
base of the appliance at the back.
^Ensure that the hose is fitted correctly
and that it is water tight.
^Turn on the stopcock slowly and
check the whole water system for
leaks.
^The appliance can then be
connected to the electricity supply.
^Push the appliance into its final
position.
When doing so, make sure that the
stainless steel hose is not kinked or
damaged.
After a maximum of 24 hours the first
ice cubes will drop out of...

Electrical connection U.K.
All electrical work should be carried out
by a suitably qualified and competent
person in strict accordance with current
local and national safety regulations
(BS 7671 in the UK).
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an a.c. single phase
220-240 V 50 Hz supply.
Please ensure that the connection data
quoted on the data plate match the
household mains supply.
Connection should be made via a
suitable switched socket which is easily...

Do not place any appliance which
gives off heat, such as a toaster or
microwave oven, on top of this
appliance, as this would increase
the appliances energy
consumption.
This appliance must not be installed
directly next to another refrigerator
or freezer.
It does not have side-wall heating,
so installation next to another
refrigerator or freezer could cause a
build-up of condensation between
them.
Further information is available from
your dealer.
Location
This appliance should be installed in a
dry,...

Ventilation
Air at the back of the appliance gets
warm. To ensure sufficient ventilation,
the air inlet and outlet must not be
covered or blocked in any way. They
should be dusted on a regular basis.
Installation
^Remove the cable clip from the back
of the appliance.
^Check that all parts at the back of the
appliance are unhindered. Carefully
remove any hindrance.
^Carefully push the appliance into
position with the back against the
wall.
Aligning the appliance
^To align the appliance, adjust the
front...

Appliance dimensions
ABC
KFN 14947 SDE ed2020 750 630
Installation
58
 

The appliance is supplied right-hand
hinged. If left-hand door hinging is
required, follow the instructions below.
To change the door hinging you will
need the following tools:
–a cross-slotted screwdriver,
–a flat-bladed screwdriver,
–a selection of Torx screwdrivers,
–a spanner.
Two people are needed for
changing the door hinging.
Removing the door handles
^
Pull door handleatowards you. Side
sectionbslides back.
^
Pull side sectionbfirmly back out of
the guides on the mounting plate.
^
Undo the 4...

Before beginning, make sure that
the door shelves are empty.
Removing the soft-close mechanism
for the upper door
^Open the refrigerator door.
^Prise open panelafrom the
soft-close mechanism by inserting a
flat-bladed screwdriver into the gap
from above and easing it off bit by
bit.
Take care not to damage the door
seal.
If the door seal becomes damaged,
the door will no longer close
properly and cooling will be
impaired.^Slide panelatowards the appliance,
and leave it hanging between the
door and the...