Miele Kfn 14947 Sdeed Operating And Installation Instructions

							^Remove coverd.
The soft-close mechanism is now no
longer fixed to the appliance.
^Remove panela.
^Slide soft-close mechanism bracket
fas far as it will go towards the
handle side of the door.
^Undo screwgon the soft-close
mechanism and on the spacer.
^Using a flat-bladed screwdriver prise
up the centre of the base of the
soft-close mechanism towards the
middle of the door.
^
Then prise the base of the soft-close
mechanism out of the socket from the
hinge side of the door.
^
Place the soft-close mechanism to
one side.
^
Push the spacer out towards the
hinge side.
^
Then place the spacer to one side.Removing the upper door:
^Gently loosen coverhby carefully
inserting a flat-bladed screwdriver
into the gap.
^Remove coverhtogether with
retaineri.
^Then separate retainerifrom cover
h, by pushing it slightly to the left
and then pulling the cover forwards
and off.
^Rotate retaineriby 180°.
^
Then fit coverhfrom the front over
retaineri, and push it over to the
right. The writing must be visible.
^
Unscrew hinge partj, turn through
180° and fit to the opposite side. If
necessary drill pilot holes for the
screws.
^
Remove coverkby sliding it
forwards from the back and then
lifting it off.
^
Remove coverlby pulling it
upwards.
Changing the door hinging
61
 
						

							Caution. The upper door is not
secure as soon as the upper hinge
plate is removed.
^Close the upper door.
^Undo screwsmin upper hinge plate
nand pull it upwards and off.
^Carefully lift the upper door off and
place it to one side.
^Make sure that you leave the hinge
pin in the hinge plate in the middle of
the appliance, as otherwise the lower
door will be unsecured.
^Then fit coverhtogether with
retainerion the opposite side.
^Refit coverlon the opposite side.
Removing the lower soft-close door
mechanism
^Open the lower door.
^
Prise open panelafrom the
soft-close mechanism and ease it off
carefully from above bit by bit.Take care not to damage the door
seal.
If the door seal becomes damaged,
the door will no longer close
properly and cooling will be
impaired.
^Slide panelatowards the appliance,
and leave it hanging between the
door and the appliance.
^Fit restraining clipb(supplied with
the appliance) onto soft-close
mechanismc.
The restraining clip stops the hinge
from snapping shut. Do not remove the
clip until told to do so.
^
Carefully remove coverdfrom the
side using a flat-bladed screwdriver.
^
With the help of another person, tip
the appliance back slightly.
Changing the door hinging
62
 
						

							^Push hinge pineup and out from
underneath.
The soft-close mechanism is now no
longer fixed to the appliance.
^Remove panela.
^
Slide soft-close mechanism bracket
fas far as it will go towards the
handle side of the door.
^
Undo screwgon the soft-close
mechanism and on the spacer.
^
Using a flat-bladed screwdriver prise
up the centre of the base of the
soft-close mechanism towards the
middle of the door.
^
Then prise the base of the soft-close
mechanism out of the socket from the
hinge side of the door.
^
Place the soft-close mechanism to
one side.^Push the spacer out towards the
hinge side.
^Then place the spacer to one side.
Removing the lower door
^Close the lower appliance door.
^Pull the middle hinge piniupwards
to remove it.
^Carefully lift the lower door off and
place it to one side.
^Pull coverjoff.
^
Unscrew hinge platek, turn it
through 180° and fit it on the opposite
side.
^
Turn plastic coverh180° and refit it
in the centre of hinge platek.
^
Refit coverjon the opposite side.
Changing the door hinging
63
 
						

							^Remove caplfrom the bush in the
door and refit on the opposite side.
Refitting the lower door
^
Remove coveraby pulling it
forwards.
^
Pull coverboff.
^
Screw the foot into hinge pincas far
as it will go.^With the help of another person,
carefully tilt the appliance backwards
and pull hinge pincout.
^Take care not to lose hinge bushd.
^Undo screwseand take hinge plate
foff.
^Remove covergand undo the
screws. Refit the screws and cover on
the opposite side.
^Refit hinge platefonto the other
side using the 2outerscrews. To
make it possible to align the door
later, do not replace thecentre
screw at this stage.
^Unscrew parthfrom hinge platef,
rotate it by 180° and refit into the hole
on the opposite side of the hinge
plate.
^Refit coverbon the opposite side.
^With the help of another person,
carefully tip the appliance back and
refit hinge pincfrom below into
hinge platef. The notch at the
bottom of the hinge plate should face
forwards.
^
Replace hinge bushdon hinge pin
c.
^
Refit covera.
^
Place the lower door onto hinge pin
cfrom above.
^
Close the lower appliance door.
Changing the door hinging
64
 
						

							^Fit hinge piniinto middle hinge
platekin the lower door.
Replacing the lower soft-close door
mechanism
^
Remove coverafrom panelb,
rotate it by 180° and refit it on the
other side.^Insert the spacer into the socket on
the handle side (A).
^Then insert the soft-close mechanism
into the socket on the hinge side (B).
Push both parts from the middle
towards the outside so that they
click firmly into position.
^
Attach the spacer and the soft-close
mechanism securely using screwc.
Changing the door hinging
65
 
						

							^Attach panelbto soft-close
mechanism bracketd.
^Align bracketdto the hinge plate,
and insert pinefrom above so that
the right angle fits into the recess.
^Click coverfback into place.
Make sure that coverffits properly so
that the door can be closed without
hindrance and the pin is protected.
^Remove retaining clipg.
^
Replace panelbonto the soft-close
mechanism from above, clicking it
back into place first at the bottom
and then at the top.
^
Close the lower appliance door.Refitting the upper door:
^Then fit the top door on middle hinge
pini.
^Close the upper door.
^Fit hinge platenonto the opposite
side and secure it with screwsm.
If necessary drill pilot holes for the
screws or use a battery operated
screwdriver.
^Refit coverkon the opposite side.
^Align the door with the appliance
housing using the long slots in the
lower hinge plate. Then tighten the
screws.
Changing the door hinging
66
 
						

							Replacing the upper soft-close door
mechanism:
^Remove coverafrom panelb,
rotate it by 180° and refit it on the
other side.
^
Insert the spacer into the socket on
the handle side (A).
^
Then insert the soft-close mechanism
into the socket on the hinge side (B).
Push both parts from the middle
towards the outside so that they
click firmly into position.^Attach the spacer and the soft-close
mechanism securely using screwc.
^Attach panelbto soft-close
mechanism bracketd.
^
Push covereon from the side so
that the openings for the pinfare
vertically aligned.
^
Align bracketdto the hinge plate,
and insert pinffrom above so that
the right angle fits into the recess.
^
Clip covereinto position.
Make sure that coverefits properly so
that the door can be closed without
hindrance and the pin is protected.
Changing the door hinging
67
 
						

							^Remove retaining clipg.
^Replace panelbonto the soft-close
mechanism from above, clicking it
back into place first at the bottom
and then at the top.
^Close the upper door.
Refitting the handle:
Please make sure you follow the
instructions below carefully when
you refit the handle. The door seal
will be damaged if the handle is
fitted incorrectly.
^
Loosely attach the handle to the
opposite side of the door with the two
front screwsb.Mounting platecmust be positioned
on the side of the door so that when the
door isclosedit is flush with the side of
the appliance.
If this is not the case,
^tighten both grub screwsawith an
allen key until mounting plateclines
up correctly.
^Then tighten all 4 fixing screwsb.
^Slide the side section of the handle
dinto the guides on the mounting
plate until it clicks into place.
It is important to check that the side
section of the handleddoes not
come into contact with the door seal
when opening the door, as this
would damage the door seal
permanently.
If, after you have refitted the handle,
you find that the side section does
touch the door seal when the door is
opened:
^
Realign mounting platecwith grub
screwsauntil the mounting plate
and the side section of the handled
are at the correct angle and the side
section does not touch the door seal
when the door is opened.
Changing the door hinging
68
 
						

							The appliance doors can be aligned
with the housing after they have been
fitted.
In the following illustration the door
is not shown in the closed position to
make it easier to see what you have
to do.
Align thelower doorusing the long
outer slots in the lower hinge plate:
^Remove centre screwafrom the
hinge plate.
^
Slightly loosen both outer screwsb.
^
Align the door by sliding the hinge
plate to the left or right.
^
Then tighten screwsbagain. Screw
adoes not need to be used again.Align theupper doorusing the long
outer slots in the middle hinge plate:
^Slightly loosen the three screwsc.
^Align the door by sliding the hinge
plate to the left or right.
^Then tighten screwsc.
Aligning the appliance doors
69
 
						

							aTop box
bAppliance
cHousing unit
dWall
The appliance can be installed in a
kitchen run. To match the height of the
rest of the kitchen, the appliance can
be fitted with a suitable top boxa.
A ventilation gap of at least 50 mm
depth must be allowed for behind the
appliance across the entire width of the
top box for air to circulate.
The cross section of the air outlet under
the room ceiling must be at least
300 cm
2to ensure that air can circulate
without hindrance. Otherwise the
appliance has to work harder, resulting
in an increase in electricity
consumption.
The air inlet and outlet must not be
covered or blocked in any way.
They should be dusted on a regular
basis.
When built into a kitchen run (max.
depth 580 mm) the appliance can be
installed directly next to a kitchen
furniture housing unit. The appliance
door will protrude in front of furniture
fronts at the sides by 34 mm and by
55 mm in the middle of the door. This
enables the doors to be opened and
shut without being obstructed.
When installednext to a wallda
distance of approx. 55 mm must be
maintained on the hinge side between
the walldand the applianceb,so
that the doors and the handles have
sufficient space for opening.
Building in the appliance
70