Miele Kfn 14827 Sdeed Operating And Installation Instructions

...dn appears in the temperature
display.
The demonstration function is activated.
^Call the Service Department.
. . . you cannot switch the ice cube
maker on.
^Check whether the appliance is
connected to the electricity supply.
. . . the ice cube maker is not
producing any ice cubes.
^Was the water inlet pipe purged of air
by a qualified and competent person
before the appliance was used for
the first time?
^Check whether the ice cube maker is
switched on.
^Check whether the freezer section is
switched...

. . . the floor of the PerfectFresh zone
is wet.
The condensate drain hole is blocked.
^Clean the condensate channel and
drain hole.
If you still cannot remedy the fault
having followed these suggestions,
please contact the Miele Service
Department.
To prevent unnecessary loss of
temperature it is advisable not to
open the doors while waiting for the
appliance to be serviced.
Problem solving guide
52
 

Normal noises What causes them
Brrrrr...Humming noise made by the motor (compressor). This noise can
get louder for brief periods when the motor is switching on.
Blubb, blubb....A gurgling noise can be heard when coolant is circulating
through the pipes.
Click....Clicking sounds are made when the thermostat switches the
motor on and off.
Sssrrrrr....On multi-zone and frost-free appliances you can sometimes just
hear the movement of air circulating inside the appliance.
Creak ...Creaking sounds can be...

In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
–your Miele Dealer
or
–Miele
(see back cover for contact details).
When contacting your Dealer or Miele,
please quote the model and serial
number of your appliance. This
information is given on the data plate
inside your appliance.
Please note that telephone calls may
be monitored and recorded for
training purposes.
N.B. A call-out charge will be applied
for service visits where the problem...

Notes on connecting to the
mains water supply
Connection to the mains water
supply should only be carried out by
a qualified and competent person in
accordance with national and local
regulations.
The water quality must conform to
the requirements for drinking water
in the country the appliance is being
installed in.
– This appliance complies with IEC
61770 and EN 61770 (ATS 5200.101
in Australia).
– All items used for connecting the
appliance to the mains water supply
must comply with the current...

^The stainless steel hose should be
attached to the solenoid valve at the
base of the appliance at the back.
^Ensure that the hose is fitted correctly
and that it is water tight.
^Turn on the stopcock slowly and
check the whole water system for
leaks.
^The appliance can then be
connected to the electricity supply.
^Push the appliance into its final
position.
When doing so, make sure that the
stainless steel hose is not kinked or
damaged.
After a maximum of 24 hours the first
ice cubes will drop out of...

Electrical connection U.K.
All electrical work should be carried out
by a suitably qualified and competent
person in strict accordance with current
local and national safety regulations
(BS 7671 in the UK).
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an a.c. single phase
220-240 V 50 Hz supply.
Please ensure that the connection data
quoted on the data plate match the
household mains supply.
Connection should be made via a
suitable switched socket which is easily...

Do not place any appliance which
gives off heat, such as a toaster or
microwave oven, on top of this
appliance, as this would increase
the appliances energy
consumption.
This appliance has side-wall heating
and can be installed side-by-side
with another refrigeration appliance.
Please ask your supplier for details
of suitable appliances.
Location
This appliance should be installed in a
dry, well-ventilated room. It should not
be installed where it is exposed to
direct sunlight or directly adjacent to a...

Ventilation
Air at the back of the appliance gets
warm. To ensure sufficient ventilation the
air inlet and outlet must not be covered
or blocked in any way. They should be
dusted on a regular basis.
Installation
^Remove the cable clip from the back
of the appliance.
^Check that all parts at the back of the
appliance are unhindered. Carefully
remove any hindrance.
^Carefully push the appliance into
position. The appliance can be placed
directly against a wall.
Aligning the appliance
^
To align the...

Appliance dimensions
ABC
KFN 14827 SDE ed/cs1850 mm 600 mm 630 mm
Installation
60