Miele Kfn 14827 Sdeed Operating And Installation Instructions

							...dn appears in the temperature
display.
The demonstration function is activated.
^Call the Service Department.
. . . you cannot switch the ice cube
maker on.
^Check whether the appliance is
connected to the electricity supply.
. . . the ice cube maker is not
producing any ice cubes.
^Was the water inlet pipe purged of air
by a qualified and competent person
before the appliance was used for
the first time?
^Check whether the ice cube maker is
switched on.
^Check whether the freezer section is
switched on.
^Check whether the water inlet is
open.
^
Check that the ice cube drawer has
been closed properly.
It can take up to 24 hours to produce
the first ice cubes.
. . . the ice cube maker is only
producing small ice cubes.
The size of ice cubes which are
produced over a certain period of time
will depend on the water pressure
present.
If the ice cube maker is only producing
small ice cubes the water pressure is low.
^
Lengthen the water intake time for the
ice cube maker (see Making ice
cubes).. . . the indicator light on the ice cube
maker flashes.
The ice cube tray is in its cleaning
position (see Cleaning and care).
If this is not the case, then there is a
fault.
^Call the Service Department.
. . . you cannot switch the appliance
off.
The safety lock has been activated.
. . . the interior lighting in the
PerfectFresh zone is not working.
Was the door left open for too long?
The lighting switches itself off
automatically after approx. 15 minutes if
the door is left open.
If this is not the case, then the interior
lighting is defective.
^Call the Service Department.
The LED lighting may only be repaired
or replaced by a service technician.
There are live electrical components
under the cover. Danger of injury and
damage.
Do not remove the cover. If the
cover is damaged or needs to be
removed due to damage,exercise
caution.There are lasers in the
lighting (laser beam class 1M) which
you should avoid looking at directly.
Do not use optical instruments
(magnifying glass or similar) to look
at the lighting either.
Problem solving guide
51
 
						

							. . . the floor of the PerfectFresh zone
is wet.
The condensate drain hole is blocked.
^Clean the condensate channel and
drain hole.
If you still cannot remedy the fault
having followed these suggestions,
please contact the Miele Service
Department.
To prevent unnecessary loss of
temperature it is advisable not to
open the doors while waiting for the
appliance to be serviced.
Problem solving guide
52
 
						

							Normal noises What causes them
Brrrrr...Humming noise made by the motor (compressor). This noise can
get louder for brief periods when the motor is switching on.
Blubb, blubb....A gurgling noise can be heard when coolant is circulating
through the pipes.
Click....Clicking sounds are made when the thermostat switches the
motor on and off.
Sssrrrrr....On multi-zone and frost-free appliances you can sometimes just
hear the movement of air circulating inside the appliance.
Creak ...Creaking sounds can be heard when material inside the
appliance expands.
Remember that the noise of the compressor and the coolant circulating in the
system is unavoidable.
Noises that you can
easily rectifyWhat causes them, and what can you do about
them
Rattling, vibrating The appliance is uneven:Realign the appliance using a spirit
level, by raising or lowering the screw feet underneath the
appliance.
The appliance is touching another appliance or piece of
furniture:Move it away.
Drawers, baskets or shelves are unstable or sticking:Check
all removable items and refit them correctly.
Are any bottles or containers unstable or knocking against
each other?Separate them.
The transport cable clips are hanging loose at the back of
the appliance:Remove the clips.
Noises
53
 
						

							In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
–your Miele Dealer
or
–Miele
(see back cover for contact details).
When contacting your Dealer or Miele,
please quote the model and serial
number of your appliance. This
information is given on the data plate
inside your appliance.
Please note that telephone calls may
be monitored and recorded for
training purposes.
N.B. A call-out charge will be applied
for service visits where the problem
could have been resolved as described
in these instructions.
Guarantee
For information on the appliance
guarantee specific to your country
please contact Miele. See back cover
for contact details.
In the U.K. your appliance is
guaranteed for 2 years from the date of
delivery. However, you must activate
your cover by calling 0845 365 6640 or
registering online at www.miele.co.uk.
After Sales / Guarantee
54
 
						

							Notes on connecting to the
mains water supply
Connection to the mains water
supply should only be carried out by
a qualified and competent person in
accordance with national and local
regulations.
The water quality must conform to
the requirements for drinking water
in the country the appliance is being
installed in.
– This appliance complies with IEC
61770 and EN 61770 (ATS 5200.101
in Australia).
– All items used for connecting the
appliance to the mains water supply
must comply with the current national
and local safety regulations in the
country in which the appliance is
being installed.
–
The appliance is only suitable for
connection to the cold water supply.
–
The water pressure (flow rate) must
be between 1.5 and 6 bar.
–
The stainless steel hose is 1.5 m
long. This may only be lengthened
by means of a Miele extension hose.
This extension hose is available from
the Miele Spare Parts Department
and must only be fitted by a suitably
qualified fitter.
–
A stopcock must be provided
between the stainless steel hose and
the household water supply to
ensure that the water supply can be
cut off if necessary.
The stopcock should be easily
accessible after the appliance has
been built-in.
Connection to the water inlet
Before making plumbing
connections, ensure the appliance is
disconnected from the mains
electricity supply.
Connection to the mains water supply
should incorporate a mains stopcock
with
3/4 thread.
^
Connect the stainless steel hose to
the stopcock.
^
Ensure that it is screwed into position
correctly.
Before using the appliance for the first
time the water inlet pipe should be
purged of air by a qualified and
competent person.
–
To do so the stainless steel hose
should be filled as far as possible
with water before being connected to
the solenoid valve.
–
Mop up any spillages with a cloth.
Mains water connection
55
 
						

							^The stainless steel hose should be
attached to the solenoid valve at the
base of the appliance at the back.
^Ensure that the hose is fitted correctly
and that it is water tight.
^Turn on the stopcock slowly and
check the whole water system for
leaks.
^The appliance can then be
connected to the electricity supply.
^Push the appliance into its final
position.
When doing so, make sure that the
stainless steel hose is not kinked or
damaged.
After a maximum of 24 hours the first
ice cubes will drop out of the ice
cube maker and collect in the
drawer.
Mains water connection
56
 
						

							Electrical connection U.K.
All electrical work should be carried out
by a suitably qualified and competent
person in strict accordance with current
local and national safety regulations
(BS 7671 in the UK).
The appliance is supplied with a mains
cable and moulded plug ready for
connection to an a.c. single phase
220-240 V 50 Hz supply.
Please ensure that the connection data
quoted on the data plate match the
household mains supply.
Connection should be made via a
suitable switched socket which is easily
accessible. For extra safety it is
advisable to protect the appliance with
a suitable residual current device
(RCD).
Do not connect the appliance to the
mains electricity supply by an extension
lead. Extension leads do not guarantee
the required safety of the appliance
(e.g. danger of overheating).
This appliance must not be connected
to the inverter of an autonomous power
supply, e.g. a solar power system.
When switching the appliance on, a
surge in power could trigger the safety
cut-out mechanism. This could damage
the electronic unit.
The appliance must not be used with
so-called energy saving devices. These
reduce the energy supply to the
appliance which could then become
too warm. Using such devices could
alter the specification of the product.Non-rewireable plugs (BS 1363)
The fuse cover must be re-fitted when
changing the fuse, and if the fuse cover
is lost, the plug must not be used until a
suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is
embossed in words in the base of the
plug (as applicable to the design of the
plug fitted).
Replacement fuses should be ASTA
approved to BS 1362 and have the
correct rating. Replacement fuses and
fuse covers may be purchased from
your local electrical supplier.
WARNING
THIS APPLIANCE MUST BE
EARTHED
Electrical connection
57
 
						

							Do not place any appliance which
gives off heat, such as a toaster or
microwave oven, on top of this
appliance, as this would increase
the appliances energy
consumption.
This appliance has side-wall heating
and can be installed side-by-side
with another refrigeration appliance.
Please ask your supplier for details
of suitable appliances.
Location
This appliance should be installed in a
dry, well-ventilated room. It should not
be installed where it is exposed to
direct sunlight or directly adjacent to a
heat-producing appliance such as an
oven or a radiator. The room
temperature should not go above or
below the climate range for which the
appliance is designed. The higher the
ambient temperature of the room, the
more energy the appliance requires to
operate.
Important: tropical / humid
environments
During periods of high humidity, some
condensation may appear on outside
surfaces of cooling appliances. This
condensation will disappear when
humidity levels drop. For prevention, it
is advisable to install the appliance
with sufficient ventilation in a dry
and/or an air-conditioned room.
Please ensure that doors are closing
and sealing properly.
Please ensure that the appliance is
installed in accordance with these
installation instructions and that the
handle is fitted correctly. Should you
require further assistance please
contact your Miele customer service
centre.
Climate range
The appliance is designed for use
within certain climate ranges (ambient
temperatures), and should not be used
outside this range. The climate range of
the appliance is stated on the data
plate inside the appliance.
Climate range Ambient room
temperature
SN
N
ST
T
SN-ST
SN-T+10°C to +32°C
+16°C to +32°C
+16°C to +38°C
+16°C to +43°C
+10°C to +38°C
+10°C to +43°C
Operating in a room which is too cold
will cause the cooling system to switch
off for too long, causing the internal
temperatures in the appliance to rise
with the risk of frozen food deteriorating
and going off.
Installation
58
 
						

							Ventilation
Air at the back of the appliance gets
warm. To ensure sufficient ventilation the
air inlet and outlet must not be covered
or blocked in any way. They should be
dusted on a regular basis.
Installation
^Remove the cable clip from the back
of the appliance.
^Check that all parts at the back of the
appliance are unhindered. Carefully
remove any hindrance.
^Carefully push the appliance into
position. The appliance can be placed
directly against a wall.
Aligning the appliance
^
To align the appliance, adjust the feet
using the spanner supplied.^If necessary, also align the two rear
adjusting devicesausing a socket
wrenchb.
Turn the adjusting device clockwise
to raise the appliance up at the back.
Levelling the appliance door
^
Ensurethat you unscrew adjusting
footcfrom the hinge plate until it sits
on the floor. Then unscrew the foot by
a further 90°.
Installation
59
 
						

							Appliance dimensions
ABC
KFN 14827 SDE ed/cs1850 mm 600 mm 630 mm
Installation
60