Miele G 8066 Manual

4. Buzzer
(Programming level 5)
Programming level 5 allows you to
activate a buzzer to sound at the end of
a program or when a fault has
occurred.
To turn the buzzer off:
–Press
(Fault confirmation for F0E, F2E).
–Press
(turning off the power).
–Open the door at the end of the
program.
If the fault has not been fixed, the
buzzer will start again after power
has been restored.
Accessing programming level 5
Turn the machine off by pressing.
Press and hold theandbutton,
at the same timeturn the...

5. Altering the program
duration (Programming level 6)
The program duration can be set
between 75 and 480 seconds.
Lengthening the program duration
cannot alter how the programs relate to
each other in terms of time, e.g. the
SHORT program will always be the
shortest program.
It is only possible to set a program
duration which is shorter than or equal
to the value set for the STANDARD
program.
To lengthen the program duration of
every program, start with the
INTENSIVE program.Accessing programming level...

5.2 Altering the STANDARD program
duration
Select programming level 6.
Pressuntil6.02is displayed.
Pressonce, the display shows
the current setting120. The factory
setting is 120 seconds.
Press and holduntil the desired
value appears in the display. The
duration is set in 5 second
increments.
If you do not want to make any other
setting changes in this programming
level, proceed to step5.4.5.3 Altering the INTENSIVE program
duration
Select programming level 6.
Pressuntil6.03is displayed....

6. Resetting the factory default
settings
All settings can be reset to the factory
default settings in Programming level 7.
To do this you must first select the
factory setting and then confirm them.
After confirming the factory settings, all
adjustments are reset. Any changes
must be reentered if required.
Accessing programming level 7
Turn the machine off by pressing.
Press and hold theand
buttons,at the same timeturn the
machine on with the main switch.
The display shows the current
program...

Cleaning the wash cabinet,
tank and filters
Wash cabinet and tank
Once a day
The tank should be checked and
cleaned regularly depending on the
soiling or number of wash programs.
Always check and clean at the end of
each workday.
Pressto start the DRAIN program.
See the "Program guide".
If the cleaning result is not
satisfactory, restart the program. It
will run again but for a shorter
duration.
Pressto restart the DRAIN
program.Filters
The water in the tank may be
hot. Before taking the...

Flat filter
Take the front filter out first, by lifting
it up a little at the front.
Remove the rear filter, by lifting it up
a little at the rear.
Clean the filters thoroughly under
running water.
Reinsert the filters in the reverse
order. Make sure that you reinsert the
filters correctly. Ensure that the filters
sit flat in the base of the wash
cabinet.Fine filter
Remove the flat filters.
Turn the fine filter counterclockwise
to remove it from the drain.
Spin the propeller of the drain pump
few...

Cleaning the control panel
Only clean the control panel with a
damp cloth, a plastic cleaner or
disinfectant.
Do not use too much water when
cleaning the controls. Water could
penetrate into the electronics and
cause damage.
Never use abrasive cleaners,
scouring pads, steel wool, thinners,
caustic (oven)-, glass-, all purpose
cleaners or cleaners containing
ammonia on the dishwasher.
They will damage the surface.
Cleaning the exterior
Clean the exterior with a solution of
warm water and liquid...

Cleaning the drain pump and
non-return valve
If water has not been drained at the
end of a program the drain pump and
the non-return valve may be clogged.
The water in the tank may be
hot. Allow the water to cool.
Remove the flat and fine filters from
the wash cabinet.

Turn the non-return valve to the front
and take it out.

Rinse the non-return valve thoroughly
under running water.

Make sure that the vent hole is not
clogged.

Clean the vent hole if necessary with
a pointed object.The non-return...

Cleaning the water inlet filters
To protect the water inlet valve, filters
are incorporated in the intake hose
attached to the water supply. If the
filters are soiled they must be cleaned
to ensure sufficient water intake to the
wash cabinet.
The plastic valve housing on the
intake hose contains electrical
components and should not be
submerged, or run through water.
Cleaning the filter
Disconnect the machine from
electricity (unplug it or "trip" the
circuit breaker).
Close off the water...

With the aid of the following guide, minor problems can be fixed without a service call.
Repairs should only be carried out by Miele Service in accordance with local
and national safety regulations. Unauthorized repairs could cause personal
injury or machine damage.
Technical faults
Issue Possible fault Solution
Dishwasher does not
startThe door is not properly
closed.Close the door firmly.
The machine is not
plugged in.Insert the plug.
The fuse has tripped. Reset the circuit breaker.
Dishwasher stops...